Network Modeling M. Boucadair
Internet-Draft Orange
Obsoletes: 8407 (if approved) Q. Wu
Updates: 8126 (if approved) Huawei
Intended status: Best Current Practice 26 July 2023
Expires: 27 January 2024
Guidelines for Authors and Reviewers of Documents Containing YANG Data
Models
draft-boucadair-netmod-rfc8407bis-02
Abstract
This memo provides guidelines for authors and reviewers of
specifications containing YANG modules, including IANA-maintained
modules. Recommendations and procedures are defined, which are
intended to increase interoperability and usability of Network
Configuration Protocol (NETCONF) and RESTCONF protocol
implementations that utilize YANG modules. This document obsoletes
RFC 8407.
Also, this document updates RFC 8126 by providing additional
guidelines for writing the IANA considerations for RFCs that specify
IANA-maintained modules.
Discussion Venues
This note is to be removed before publishing as an RFC.
Discussion of this document takes place on the Network Modeling
Working Group mailing list (netmod@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/browse/netmod/.
Source for this draft and an issue tracker can be found at
https://github.com/boucadair/rfc8407bis.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Boucadair & Wu Expires 27 January 2024 [Page 1]
Internet-Draft Guidelines for YANG Documents July 2023
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 27 January 2024.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Changes since RFC 8407 . . . . . . . . . . . . . . . . . 5
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1. NETCONF Terms . . . . . . . . . . . . . . . . . . . . . . 7
2.2. YANG Terms . . . . . . . . . . . . . . . . . . . . . . . 7
2.3. NMDA Terms . . . . . . . . . . . . . . . . . . . . . . . 8
2.4. Requirements Notation . . . . . . . . . . . . . . . . . . 8
3. General Documentation Guidelines . . . . . . . . . . . . . . 8
3.1. Module Copyright . . . . . . . . . . . . . . . . . . . . 9
3.2. Code Components . . . . . . . . . . . . . . . . . . . . . 9
3.2.1. Example Modules . . . . . . . . . . . . . . . . . . . 10
3.3. Terminology Section . . . . . . . . . . . . . . . . . . . 10
3.4. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 10
3.5. Narrative Sections . . . . . . . . . . . . . . . . . . . 10
3.6. Definitions Section . . . . . . . . . . . . . . . . . . . 11
3.7. Security Considerations Section . . . . . . . . . . . . . 12
3.7.1. Security Considerations Section Template . . . . . . 12
3.8. IANA Considerations Section . . . . . . . . . . . . . . . 14
3.8.1. Documents That Create a New Namespace . . . . . . . . 14
3.8.2. Documents That Extend an Existing Namespace . . . . . 14
3.9. References Sections . . . . . . . . . . . . . . . . . . . 15
3.10. Validation Tools . . . . . . . . . . . . . . . . . . . . 15
3.11. Module Extraction Tools . . . . . . . . . . . . . . . . . 16
3.12. Module Usage Examples . . . . . . . . . . . . . . . . . . 16
4. YANG Usage Guidelines . . . . . . . . . . . . . . . . . . . . 16
Boucadair & Wu Expires 27 January 2024 [Page 2]
Internet-Draft Guidelines for YANG Documents July 2023
4.1. Module Naming Conventions . . . . . . . . . . . . . . . . 17
4.2. Prefixes . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3. Identifiers . . . . . . . . . . . . . . . . . . . . . . . 19
4.3.1. Identifier Naming Conventions . . . . . . . . . . . . 19
4.4. Defaults . . . . . . . . . . . . . . . . . . . . . . . . 19
4.5. Conditional Statements . . . . . . . . . . . . . . . . . 20
4.6. XPath Usage . . . . . . . . . . . . . . . . . . . . . . . 21
4.6.1. XPath Evaluation Contexts . . . . . . . . . . . . . . 21
4.6.2. Function Library . . . . . . . . . . . . . . . . . . 22
4.6.3. Axes . . . . . . . . . . . . . . . . . . . . . . . . 23
4.6.4. Types . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6.5. Wildcards . . . . . . . . . . . . . . . . . . . . . . 24
4.6.6. Boolean Expressions . . . . . . . . . . . . . . . . . 25
4.7. YANG Definition Lifecycle Management . . . . . . . . . . 26
4.8. Module Header, Meta, and Revision Statements . . . . . . 27
4.9. Namespace Assignments . . . . . . . . . . . . . . . . . . 28
4.10. Top-Level Data Definitions . . . . . . . . . . . . . . . 30
4.11. Data Types . . . . . . . . . . . . . . . . . . . . . . . 30
4.11.1. Fixed-Value Extensibility . . . . . . . . . . . . . 31
4.11.2. Patterns and Ranges . . . . . . . . . . . . . . . . 31
4.11.3. Enumerations and Bits . . . . . . . . . . . . . . . 32
4.11.4. Union Types . . . . . . . . . . . . . . . . . . . . 33
4.11.5. Empty and Boolean . . . . . . . . . . . . . . . . . 34
4.12. Reusable Type Definitions . . . . . . . . . . . . . . . . 35
4.13. Reusable Groupings . . . . . . . . . . . . . . . . . . . 36
4.14. Data Definitions . . . . . . . . . . . . . . . . . . . . 36
4.14.1. Non-Presence Containers . . . . . . . . . . . . . . 38
4.14.2. Top-Level Data Nodes . . . . . . . . . . . . . . . . 39
4.15. Operation Definitions . . . . . . . . . . . . . . . . . . 39
4.16. Notification Definitions . . . . . . . . . . . . . . . . 39
4.17. Feature Definitions . . . . . . . . . . . . . . . . . . . 40
4.18. YANG Data Node Constraints . . . . . . . . . . . . . . . 41
4.18.1. Controlling Quantity . . . . . . . . . . . . . . . . 41
4.18.2. "must" versus "when" . . . . . . . . . . . . . . . . 41
4.19. "augment" Statements . . . . . . . . . . . . . . . . . . 41
4.19.1. Conditional Augment Statements . . . . . . . . . . . 42
4.19.2. Conditionally Mandatory Data Definition
Statements . . . . . . . . . . . . . . . . . . . . . 42
4.20. Deviation Statements . . . . . . . . . . . . . . . . . . 44
4.21. Extension Statements . . . . . . . . . . . . . . . . . . 45
4.22. Data Correlation . . . . . . . . . . . . . . . . . . . . 45
4.22.1. Use of "leafref" for Key Correlation . . . . . . . . 46
4.23. Operational State . . . . . . . . . . . . . . . . . . . . 47
4.23.1. Combining Operational State and Configuration
Data . . . . . . . . . . . . . . . . . . . . . . . . 48
4.23.2. Representing Operational Values of Configuration
Data . . . . . . . . . . . . . . . . . . . . . . . . 48
4.23.3. NMDA Transition Guidelines . . . . . . . . . . . . . 49
Boucadair & Wu Expires 27 January 2024 [Page 3]
Internet-Draft Guidelines for YANG Documents July 2023
4.24. Performance Considerations . . . . . . . . . . . . . . . 52
4.25. Open Systems Considerations . . . . . . . . . . . . . . . 53
4.26. Guidelines for Constructs Specific to YANG 1.1 . . . . . 53
4.26.1. Importing Multiple Revisions . . . . . . . . . . . . 53
4.26.2. Using Feature Logic . . . . . . . . . . . . . . . . 53
4.26.3. "anyxml" versus "anydata" . . . . . . . . . . . . . 54
4.26.4. "action" versus "rpc" . . . . . . . . . . . . . . . 54
4.27. Updating YANG Modules (Published versus Unpublished) . . 55
5. IANA-Maintained Modules . . . . . . . . . . . . . . . . . . . 55
5.1. Context . . . . . . . . . . . . . . . . . . . . . . . . . 55
5.2. Guidelines for IANA-Maintained Modules . . . . . . . . . 56
5.3. Guidance for Writing the IANA Considerations for RFCs
Defining IANA-Maintained Modules . . . . . . . . . . . . 58
5.3.1. Template for IANA-Maintained Modules with
Identities . . . . . . . . . . . . . . . . . . . . . 59
5.3.2. Template for IANA-Maintained Modules with
Enumerations . . . . . . . . . . . . . . . . . . . . 59
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 60
7. Security Considerations . . . . . . . . . . . . . . . . . . . 61
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 61
8.1. Normative References . . . . . . . . . . . . . . . . . . 61
8.2. Informative References . . . . . . . . . . . . . . . . . 63
Appendix A. Module Review Checklist . . . . . . . . . . . . . . 66
Appendix B. YANG Module Template . . . . . . . . . . . . . . . . 68
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 70
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 70
1. Introduction
The standardization of network configuration interfaces for use with
network configuration management protocols, such as the Network
Configuration Protocol [RFC6241] and the RESTCONF protocol [RFC8040],
requires a modular set of data models that can be reused and extended
over time.
This document defines a set of usage guidelines for documents
containing YANG 1.1 [RFC7950] and YANG 1.0 [RFC6020] data models,
including IANA-maintained modules. YANG is used to define the data
structures, protocol operations, and notification content used within
a NETCONF and/or RESTCONF server. YANG is also used to define
abstract data structures [RFC8791]. A NETCONF or RESTCONF server
that supports a particular YANG module will support client NETCONF
and/or RESTCONF operation requests, as indicated by the specific
content defined in the YANG module.
Boucadair & Wu Expires 27 January 2024 [Page 4]
Internet-Draft Guidelines for YANG Documents July 2023
Many YANG constructs are defined as optional to use, such as the
"description" statement. However, in order to make YANG modules more
useful, it is desirable to define a set of usage guidelines that
entails a higher level of compliance than the minimum level defined
in the YANG specification [RFC7950].
In addition, YANG allows constructs such as infinite length
identifiers and string values, or top-level mandatory nodes, that a
compliant server is not required to support. Only constructs that
all servers are required to support can be used in IETF YANG modules.
This document defines usage guidelines related to the NETCONF
operations layer and NETCONF content layer, as defined in [RFC6241],
and the RESTCONF methods and RESTCONF resources, as defined in
[RFC8040].
These guidelines are intended to be used by authors and reviewers to
improve the readability and interoperability of published YANG data
models.
Section 5.3 updates [RFC8126] by providing guidance for writing the
IANA considerations for RFCs that specify IANA-maintained modules.
Note that this document is not a YANG tutorial, and the reader is
expected to know the YANG data modeling language before implementing
the guidance in this document.
1.1. Changes since RFC 8407
The following changes have been made to the guidelines published in
[RFC8407]:
* Implemented errata 5693, 5800, 6899, and 7416.
* Updated the terminology.
* Updated the URL of the IETF authors guidelines.
* Added code markers for the security template.
* Updated the YANG security considerations template to reflect the
latest version maintained in the Wiki.
* Added statements that the security template is not required for
modules that follow [RFC8791].
Boucadair & Wu Expires 27 January 2024 [Page 5]
Internet-Draft Guidelines for YANG Documents July 2023
* Added a statement that the RFCs that are listed in the security
template are to be listed as normative references in documents
that use the template.
* Added a note that folding of the examples should be done as per
[RFC8792] conventions.
* Added a note that RFC8792-folding of YANG modules can be used if
and only if native YANG features (e.g., break line, "+") are not
sufficient.
* Added tool validation checks to ensure that YANG modules fit into
the line limits of an I-D.
* Added tool validation checks of JSON-encoded examples.
* Updated many examples to be aligned with the consistent
indentation recommendation.
* Updated the IANA considerations to encourage registration requests
to indicate whether a module is maintained by IANA or not.
* Added guidelines for IANA-maintained modules.
2. Terminology
The following terms are used throughout this document:
IANA-maintained module: A YANG module that is maintained by IANA
(e.g., "iana-tunnel-type" [RFC8675] or "iana-pseudowire-types"
[RFC9291]).
IETF module: A YANG module that is published by the IETF and which
is not maintained by IANA.
published: A stable release of a module or submodule. For example,
the "Request for Comments" described in Section 2.1 of [RFC2026]
is considered a stable publication.
unpublished: An unstable release of a module or submodule. For
example the "Internet-Draft" described in Section 2.2 of [RFC2026]
is considered an unstable publication that is a work in progress,
subject to change at any time.
YANG fragment: A set of YANG statements that are not intended to
Boucadair & Wu Expires 27 January 2024 [Page 6]
Internet-Draft Guidelines for YANG Documents July 2023
represent a complete YANG module or submodule. These statements
are not intended for actual use, except to provide an example of
YANG statement usage. The invalid syntax "..." is sometimes used
to indicate that additional YANG statements would be present in a
real YANG module.
YANG tree diagram: A diagram representing the contents of a YANG
module, as defined in [RFC8340]. It is also called a "tree
diagram".
2.1. NETCONF Terms
The following terms are defined in [RFC6241] and are not redefined
here:
* capabilities
* client
* operation
* server
2.2. YANG Terms
The following terms are defined in [RFC7950] and are not redefined
here:
* data node
* module
* namespace
* submodule
* version
* YANG
* YIN
Note that the term 'module' may be used as a generic term for a YANG
module or submodule. When describing properties that are specific to
submodules, the term 'submodule' is used instead.
Boucadair & Wu Expires 27 January 2024 [Page 7]
Internet-Draft Guidelines for YANG Documents July 2023
2.3. NMDA Terms
The following terms are defined in [RFC8342] and are not redefined
here:
* configuration
* conventional configuration datastore
* datastore
* operational state
* operational state datastore
2.4. Requirements Notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. General Documentation Guidelines
YANG modules under review are likely to be contained in Internet-
Drafts (I-Ds). All guidelines for I-D authors [ID-Guidelines] MUST
be followed. The guidelines for RFCs should be followed and are
defined in the following: [RFC7322] (and any future RFCs that
obsolete it), [RFC-STYLE], and [RFC7841].
The following sections MUST be present in an I-D containing a YANG
module:
* Narrative sections
* Definition sections
* Security Considerations section
* IANA Considerations section
* References section
There are three usage scenarios for YANG that can appear in an I-D or
RFC:
* normative module or submodule
Boucadair & Wu Expires 27 January 2024 [Page 8]
Internet-Draft Guidelines for YANG Documents July 2023
* example module or submodule
* example YANG fragment not part of any module or submodule
The guidelines in this document refer mainly to a normative module or
submodule but may be applicable to example modules and YANG fragments
as well.
3.1. Module Copyright
The module "description" statement MUST contain a reference to the
latest approved IETF Trust Copyright statement, which is available
online at:
3.2. Code Components
Each normative YANG module or submodule contained within an I-D or
RFC is considered to be a code component. The strings "" and "" MUST be used to identify each code
component.
The "" tag SHOULD be followed by a string identifying
the file name specified in Section 5.2 of [RFC7950]. The name string
form that includes the revision date SHOULD be used. The revision
date MUST match the date used in the most recent revision of the
module.
The following example is for the "2016-03-20" revision of the "ietf-
foo" module:
file "ietf-foo@2016-03-20.yang"
module ietf-foo {
namespace "urn:ietf:params:xml:ns:yang:ietf-foo";
prefix "foo";
organization "...";
contact "...";
description "...";
revision 2016-03-20 {
description "Latest revision";
reference "RFC XXXX: Foo Protocol";
}
// ... more statements
}
Boucadair & Wu Expires 27 January 2024 [Page 9]
Internet-Draft Guidelines for YANG Documents July 2023
3.2.1. Example Modules
Example modules are not code components. The
convention MUST NOT be used for example modules.
An example module SHOULD be named using the term "example", followed
by a hyphen, followed by a descriptive name, e.g., "example-toaster".
See Section 4.9 regarding the namespace guidelines for example
modules.
3.3. Terminology Section
A terminology section MUST be present if any terms are defined in the
document or if any terms are imported from other documents.
3.4. Tree Diagrams
YANG tree diagrams provide a concise representation of a YANG module
and SHOULD be included to help readers understand YANG module
structure. Guidelines on tree diagrams can be found in Section 3 of
[RFC8340].
If YANG tree diagrams are used, then an informative reference to the
YANG tree diagrams specification MUST be included in the document.
Refer to Section 2.2 of [RFC8349] for an example of such a reference.
3.5. Narrative Sections
The narrative part MUST include an overview section that describes
the scope and field of application of the module(s) defined by the
specification and that specifies the relationship (if any) of these
modules to other standards, particularly to standards containing
other YANG modules. The narrative part SHOULD include one or more
sections to briefly describe the structure of the modules defined in
the specification.
If the module or modules defined by the specification imports
definitions from other modules (except for those defined in [RFC7950]
or [RFC6991]) or are always implemented in conjunction with other
modules, then those facts MUST be noted in the overview section; any
special interpretations of definitions in other modules MUST be noted
as well. Refer to Section 2.3 of [RFC8349] for an example of this
overview section.
If the document contains a YANG module(s) that is compliant with NMDA
[RFC8342], then the Introduction section should mention this fact.
Boucadair & Wu Expires 27 January 2024 [Page 10]
Internet-Draft Guidelines for YANG Documents July 2023
Example: The YANG data model in this document conforms to the
Network Management Datastore Architecture defined in [RFC8342].
Consistent indentation SHOULD be used for all examples, including
YANG fragments and protocol message instance data. If line wrapping
is done for formatting purposes, then this SHOULD be noted following
[RFC8792], as shown in the following example:
=============== NOTE: '\' line wrapping per RFC 8792 ================
this is a long \
value so the line needs to wrap to stay within 72 characters
Native YANG features (e.g., breaking line, "+") SHOULD be used to fit
a module into the line limits. Exceptionally, RFC8792-folding of
YANG modules MAY be used if and only if native YANG features are not
sufficient. A similar approach (e.g., use "--yang-line-length 69" or
split a tree into subtrees) SHOULD be followed for tree diagrams.
3.6. Definitions Section
This section contains the module(s) defined by the specification.
These modules SHOULD be written using the YANG 1.1 [RFC7950] syntax.
YANG 1.0 [RFC6020] syntax MAY be used if no YANG 1.1 constructs or
semantics are needed in the module. If any of the imported YANG
modules are written using YANG 1.1, then the module MUST be written
using YANG 1.1.
A YIN syntax version of the module MAY also be present in the
document. There MAY also be other types of modules present in the
document, such as Structure of Management Information Version 2
(SMIv2), which are not affected by these guidelines.
Note that if the module itself is considered normative and not an
example module or example YANG fragment, then all YANG statements
within a YANG module are considered normative. The use of keywords
defined in [RFC2119] and [RFC8174] apply to YANG "description"
statements in normative modules exactly as they would in any other
normative section.
Example YANG modules and example YANG fragments MUST NOT contain any
normative text, including any all-uppercase reserved words from
[RFC2119] and [RFC8174].
Consistent indentation and formatting SHOULD be used in all YANG
statements within a module.
See Section 4 for guidelines on YANG usage.
Boucadair & Wu Expires 27 January 2024 [Page 11]
Internet-Draft Guidelines for YANG Documents July 2023
3.7. Security Considerations Section
Each specification that defines one or more modules MUST contain a
section that discusses security considerations relevant to those
modules.
Unless the modules comply with [RFC8791], the security section MUST
be patterned after the latest approved template (available at
).
Section 3.7.1 contains the security considerations template dated
2013-05-08 and last updated on 2018-10-18. Authors MUST check the
web page at the URL listed above in case there is a more recent
version available.
In particular:
* Writable data nodes that could be especially disruptive if abused
MUST be explicitly listed by name, and the associated security
risks MUST be explained.
* Readable data nodes that contain especially sensitive information
or that raise significant privacy concerns MUST be explicitly
listed by name, and the reasons for the sensitivity/privacy
concerns MUST be explained.
* Operations (i.e., YANG "rpc" statements) that are potentially
harmful to system behavior or that raise significant privacy
concerns MUST be explicitly listed by name, and the reasons for
the sensitivity/privacy concerns MUST be explained.
Documents that define exclusively modules following the extension in
[RFC8791] are not required to include the security template in
Section 3.7.1.
3.7.1. Security Considerations Section Template
X. Security Considerations
The YANG module specified in this document defines a schema for data
that is designed to be accessed via network management protocols such
as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer
is the secure transport layer, and the mandatory-to-implement secure
transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer
is HTTPS, and the mandatory-to-implement secure transport is TLS
[RFC8446].
The Network Configuration Access Control Model (NACM) [RFC8341]
Boucadair & Wu Expires 27 January 2024 [Page 12]
Internet-Draft Guidelines for YANG Documents July 2023
provides the means to restrict access for particular NETCONF or
RESTCONF users to a preconfigured subset of all available NETCONF or
RESTCONF protocol operations and content.
-- if you have any writable data nodes (those are all the
-- "config true" nodes, and remember, that is the default)
-- describe their specific sensitivity or vulnerability.
There are a number of data nodes defined in this YANG module that are
writable/creatable/deletable (i.e., config true, which is the
default). These data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g., edit-config)
and delete operations to these data nodes without proper protection
or authentication can have a negative effect on network operations.
These are the subtrees and data nodes and their sensitivity/
vulnerability:
-- for all YANG modules you must evaluate whether any readable data
-- nodes (those are all the "config false" nodes, but also all other
-- nodes, because they can also be read via operations like get or
-- get-config) are sensitive or vulnerable (for instance, if they
-- might reveal customer information or violate personal privacy
-- laws such as those of the European Union if exposed to
-- unauthorized parties)
Some of the readable data nodes in this YANG module may be considered
sensitive or vulnerable in some network environments. It is thus
important to control read access (e.g., via get, get-config, or
notification) to these data nodes. These are the subtrees and data
nodes and their sensitivity/vulnerability:
-- if your YANG module has defined any RPC operations
-- describe their specific sensitivity or vulnerability.
Some of the RPC operations in this YANG module may be considered
sensitive or vulnerable in some network environments. It is thus
important to control access to these operations. These are the
operations and their sensitivity/vulnerability:
Note: [RFC8446], [RFC6241], [RFC6242], [RFC8341], and [RFC8040] (or
Boucadair & Wu Expires 27 January 2024 [Page 13]
Internet-Draft Guidelines for YANG Documents July 2023
future RFCs that replace any of them) have to be listed as
normative references.
3.8. IANA Considerations Section
In order to comply with IESG policy as set forth in
, every I-D that is
submitted to the IESG for publication MUST contain an IANA
Considerations section. The requirements for this section vary
depending on what actions are required of the IANA. If there are no
IANA considerations applicable to the document, then the IANA
Considerations section will state that "This document has no IANA
actions". Refer to the guidelines in [RFC8126] for more details.
Each normative YANG module MUST be registered in both the "IETF XML
Registry" [RFC3688] [IANA-XML] and the "YANG Module Names" registry
[RFC6020] [IANA-MOD-NAMES]. The registration request in the "YANG
Module Names" registry should indicate whether the module is IANA-
maintained or not. This applies to new modules and updated modules.
An example of an update registration for the "ietf-template" module
can be found in Section 6.
Additional IANA considerations applicable to IANA-maintained modules
are provided in Section 5.3.
3.8.1. Documents That Create a New Namespace
If an I-D defines a new namespace that is to be administered by the
IANA, then the document MUST include an IANA Considerations section
that specifies how the namespace is to be administered.
Specifically, if any YANG module namespace statement value contained
in the document is not already registered with IANA, then a new entry
in the "ns" subregistry within the "IETF XML Registry" MUST be
requested from the IANA.
3.8.2. Documents That Extend an Existing Namespace
It is possible to extend an existing namespace using a YANG submodule
that belongs to an existing module already administered by IANA. In
this case, the document containing the main module MUST be updated to
use the latest revision of the submodule.
Boucadair & Wu Expires 27 January 2024 [Page 14]
Internet-Draft Guidelines for YANG Documents July 2023
3.9. References Sections
For every import or include statement that appears in a module
contained in the specification that identifies a module in a separate
document, a corresponding normative reference to that document MUST
appear in the Normative References section. The reference MUST
correspond to the specific module version actually used within the
specification.
For every normative reference statement that appears in a module
contained in the specification that identifies a separate document, a
corresponding normative reference to that document SHOULD appear in
the Normative References section. The reference SHOULD correspond to
the specific document version actually used within the specification.
If the reference statement identifies an informative reference that
identifies a separate document, a corresponding informative reference
to that document MAY appear in the Informative References section.
3.10. Validation Tools
All modules need to be validated before submission in an I-D. The
'pyang' YANG compiler is freely available from GitHub:
If the 'pyang' compiler is used to validate a normative module, then
the "--ietf" command-line option MUST be used to identify any IETF
guideline issues.
If the 'pyang' compiler is used to validate an example module, then
the "--ietf" command-line option MAY be used to identify any IETF
guideline issues.
To ensure that a module fits into the line limits of an I-D, the
command "pyang -f yang --keep-comments --yang-line-length 69" should
be used.
The "yanglint" program is also freely available from GitHub.
This tool can be used to validate XPath statements within YANG
modules.
To check that JSON-encoded examples [RFC7951] comply with the target
data models, "yangson" program should be used. The "yangson" program
is freely available from GitHub.
Boucadair & Wu Expires 27 January 2024 [Page 15]
Internet-Draft Guidelines for YANG Documents July 2023
3.11. Module Extraction Tools
A version of 'rfcstrip' that will extract YANG modules from an I-D or
RFC is available. The 'rfcstrip' tool that supports YANG module
extraction is freely available at:
This tool can be used to verify that the "" and "" tags are used correctly and that the normative YANG modules
can be extracted correctly.
The "xym" tool is freely available on GitHub and can be used to
extract YANG modules from a document.
3.12. Module Usage Examples
Each specification that defines one or more modules SHOULD contain
usage examples, either throughout the document or in an appendix.
This includes example instance document snippets in an appropriate
encoding (e.g., XML and/or JSON) to demonstrate the intended usage of
the YANG module(s). Example modules MUST be validated. Refer to
Section 3.10 for tools that validate YANG modules and examples. If
IP addresses are used, then a mix of either IPv4 and IPv6 addresses
or IPv6 addresses exclusively SHOULD be used in the examples. IPv4
and IPv6 addresses/prefixes reserved for documentation are defined
[RFC5737] and [RFC3849].
4. YANG Usage Guidelines
Modules in IETF Standards Track specifications MUST comply with all
syntactic and semantic requirements of YANG 1.1 [RFC7950]. See the
exception for YANG 1.0 in Section 3.6. The guidelines in this
section are intended to supplement the YANG specification [RFC7950],
which is intended to define a minimum set of conformance
requirements.
In order to promote interoperability and establish a set of practices
based on previous experience, the following sections establish usage
guidelines for specific YANG constructs.
Only guidelines that clarify or restrict the minimum conformance
requirements are included here.
Boucadair & Wu Expires 27 January 2024 [Page 16]
Internet-Draft Guidelines for YANG Documents July 2023
4.1. Module Naming Conventions
Normative modules contained in Standards Track documents MUST be
named according to the guidelines in the IANA Considerations section
of [RFC7950].
A distinctive word or abbreviation (e.g., protocol name or working
group abbreviation) SHOULD be used in the module name. If new
definitions are being defined to extend one or more existing modules,
then the same word or abbreviation should be reused, instead of
creating a new one.
All published module names MUST be unique. For a YANG module
published in an RFC, this uniqueness is guaranteed by IANA. For
unpublished modules, the authors need to check that no other work in
progress is using the same module name.
Example modules are non-normative and SHOULD be named with the prefix
"example-".
It is suggested that a stable prefix be selected that represents the
entire organization. All normative YANG modules published by the
IETF MUST begin with the prefix "ietf-". Another standards
organization, such as the IEEE, might use the prefix "ieee-" for all
YANG modules.
Once a module name is published, it MUST NOT be reused, even if the
RFC containing the module is reclassified to "Historic" status. A
module name cannot be changed in YANG, and this would be treated as a
new module, not a name change.
4.2. Prefixes
All YANG definitions are scoped by the module containing the
definition being referenced. This allows definitions from multiple
modules to be used, even if the names are not unique. In the example
below, the identifier "foo" is used in all three modules:
Boucadair & Wu Expires 27 January 2024 [Page 17]
Internet-Draft Guidelines for YANG Documents July 2023
module example-foo {
namespace "tag:example.com,2017:example-foo";
prefix f;
container foo;
}
module example-bar {
namespace "tag:example.com,2017:example-bar";
prefix b;
typedef foo { type uint32; }
}
module example-one {
namespace "tag:example.com,2017:example-one";
prefix one;
import example-foo { prefix f; }
import example-bar { prefix b; }
augment "/f:foo" {
leaf foo { type b:foo; }
}
}
YANG defines the following rules for prefix usage:
* Prefixes are never used for built-in data types and YANG keywords.
* A prefix MUST be used for any external statement (i.e., a
statement defined with the YANG "extension" statement).
* The proper module prefix MUST be used for all identifiers imported
from other modules.
* The proper module prefix MUST be used for all identifiers included
from a submodule.
The following guidelines apply to prefix usage of the current (local)
module:
* The local module prefix SHOULD be used instead of no prefix in all
path expressions.
* The local module prefix MUST be used instead of no prefix in all
"default" statements for an "identityref" or "instance-identifier"
data type.
Boucadair & Wu Expires 27 January 2024 [Page 18]
Internet-Draft Guidelines for YANG Documents July 2023
* The local module prefix MAY be used for references to typedefs,
groupings, extensions, features, and identities defined in the
module.
Prefix values SHOULD be short but are also likely to be unique.
Prefix values SHOULD NOT conflict with known modules that have been
previously published.
4.3. Identifiers
Identifiers for all YANG identifiers in published modules MUST be
between 1 and 64 characters in length. These include any construct
specified as an "identifier-arg-str" token in the ABNF in Section 14
of [RFC7950].
4.3.1. Identifier Naming Conventions
Identifiers SHOULD follow a consistent naming pattern throughout the
module. Only lowercase letters, numbers, and dashes SHOULD be used
in identifier names. Uppercase characters, the period character, and
the underscore character MAY be used if the identifier represents a
well-known value that uses these characters. YANG does not permit
any other characters in YANG identifiers.
Identifiers SHOULD include complete words and/or well-known acronyms
or abbreviations. Child nodes within a container or list SHOULD NOT
replicate the parent identifier. YANG identifiers are hierarchical
and are only meant to be unique within the set of sibling nodes
defined in the same module namespace.
It is permissible to use common identifiers such as "name" or "id" in
data definition statements, especially if these data nodes share a
common data type.
Identifiers SHOULD NOT carry any special semantics that identify data
modeling properties. Only YANG statements and YANG extension
statements are designed to convey machine-readable data modeling
properties. For example, naming an object "config" or "state" does
not change whether it is configuration data or state data. Only
defined YANG statements or YANG extension statements can be used to
assign semantics in a machine-readable format in YANG.
4.4. Defaults
In general, it is suggested that substatements containing very common
default values SHOULD NOT be present. The following substatements
are commonly used with the default value, which would make the module
difficult to read if used everywhere they are allowed.
Boucadair & Wu Expires 27 January 2024 [Page 19]
Internet-Draft Guidelines for YANG Documents July 2023
+==============+===============+
| Statement | Default Value |
+==============+===============+
| config | true |
+--------------+---------------+
| mandatory | false |
+--------------+---------------+
| max-elements | unbounded |
+--------------+---------------+
| min-elements | 0 |
+--------------+---------------+
| ordered-by | system |
+--------------+---------------+
| status | current |
+--------------+---------------+
| yin-element | false |
+--------------+---------------+
Table 1: Statement Defaults
4.5. Conditional Statements
A module may be conceptually partitioned in several ways, using the
"if-feature" and/or "when" statements.
Data model designers need to carefully consider all modularity
aspects, including the use of YANG conditional statements.
If a data definition is optional, depending on server support for a
NETCONF or RESTCONF protocol capability, then a YANG "feature"
statement SHOULD be defined. The defined "feature" statement SHOULD
then be used in the conditional "if-feature" statement referencing
the optional data definition.
If any notification data, or any data definition, for a non-
configuration data node is not mandatory, then the server may or may
not be required to return an instance of this data node. If any
conditional requirements exist for returning the data node in a
notification payload or retrieval request, they MUST be documented
somewhere. For example, a "when" or "if-feature" statement could
apply to the data node, or the conditional requirements could be
explained in a "description" statement within the data node or one of
its ancestors (if any).
If any "if-feature" statements apply to a list node, then the same
"if-feature" statements MUST apply to any key leaf nodes for the
list. There MUST NOT be any "if-feature" statements applied to any
key leafs that do not also apply to the parent list node.
Boucadair & Wu Expires 27 January 2024 [Page 20]
Internet-Draft Guidelines for YANG Documents July 2023
There SHOULD NOT be any "when" statements applied to a key leaf node.
It is possible that a "when" statement for an ancestor node of a key
leaf will have the exact node-set result as the key leaf. In such a
case, the "when" statement for the key leaf is redundant and SHOULD
be avoided.
4.6. XPath Usage
This section describes guidelines for using the XML Path Language
(XPath) [W3C.REC-xpath] within YANG modules.
4.6.1. XPath Evaluation Contexts
YANG defines five separate contexts for evaluation of XPath
statements:
1. The "running" datastore: collection of all YANG configuration
data nodes. The document root is the conceptual container (e.g.,
"config" in the "edit-config" operation), which is the parent of
all top-level data definition statements with a "config"
statement value of "true".
2. State data + the "running" datastore: collection of all YANG data
nodes. The document root is the conceptual container, parent of
all top-level data definition statements.
3. Notification: an event notification document. The document root
is the notification element.
4. RPC Input: The document root is the conceptual "input" node,
which is the parent of all RPC input parameter definitions.
5. RPC Output: The document root is the conceptual "output" node,
which is the parent of all RPC output parameter definitions.
Note that these XPath contexts cannot be mixed. For example, a
"when" statement in a notification context cannot reference
configuration data.
Boucadair & Wu Expires 27 January 2024 [Page 21]
Internet-Draft Guidelines for YANG Documents July 2023
notification foo {
leaf mtu {
// NOT okay because when-stmt context is this notification
when "/if:interfaces/if:interface[name='eth0']";
type leafref {
// Okay because path-stmt has a different context
path "/if:interfaces/if:interface/if:mtu";
}
}
}
It is especially important to consider the XPath evaluation context
for XPath expressions defined in groupings. An XPath expression
defined in a grouping may not be portable, meaning it cannot be used
in multiple contexts and produce proper results.
If the XPath expressions defined in a grouping are intended for a
particular context, then this context SHOULD be identified in the
"description" statement for the grouping.
4.6.2. Function Library
The "position" and "last" functions SHOULD NOT be used. This applies
to implicit use of the "position" function as well (e.g.,
'//chapter[42]'). A server is only required to maintain the relative
XML document order of all instances of a particular user-ordered list
or leaf-list. The "position" and "last" functions MAY be used if
they are evaluated in a context where the context node is a user-
ordered "list" or "leaf-list".
The "id" function SHOULD NOT be used. The "ID" attribute is not
present in YANG documents, so this function has no meaning. The YANG
compiler SHOULD return an empty string for this function.
The "namespace-uri" and "name" functions SHOULD NOT be used.
Expanded names in XPath are different than YANG. A specific
canonical representation of a YANG-expanded name does not exist.
The "lang" function SHOULD NOT be used. This function does not apply
to YANG because there is no "lang" attribute set with the document.
The YANG compiler SHOULD return 'false' for this function.
The "local-name", "namespace-uri", "name", "string", and "number"
functions SHOULD NOT be used if the argument is a node-set. If so,
the function result will be determined by the document order of the
node-set. Since this order can be different on each server, the
function results can also be different. Any function call that
implicitly converts a node-set to a string will also have this issue.
Boucadair & Wu Expires 27 January 2024 [Page 22]
Internet-Draft Guidelines for YANG Documents July 2023
The "local-name" function SHOULD NOT be used to reference local names
outside of the YANG module that defines the must or when expression
containing the "local-name" function. Example of a "local-name"
function that should not be used:
/*[local-name()='foo']
The "derived-from-or-self" function SHOULD be used instead of an
equality expression for identityref values. This allows the
identities to be conceptually augmented.
Example:
// do not use
when "md-name-format = 'name-format-null'";
// this is preferred
when "derived-from-or-self(md-name-format, 'name-format-null')";
4.6.3. Axes
The "attribute" and "namespace" axes are not supported in YANG and
MAY be empty in a NETCONF or RESTCONF server implementation.
The "preceding" and "following" axes SHOULD NOT be used. These
constructs rely on XML document order within a NETCONF or RESTCONF
server configuration database, which may not be supported
consistently or produce reliable results across implementations.
Predicate expressions based on static node properties (e.g., element
name or value, and "ancestor" or "descendant" axes) SHOULD be used
instead. The "preceding" and "following" axes MAY be used if
document order is not relevant to the outcome of the expression
(e.g., check for global uniqueness of a parameter value).
The "preceding-sibling" and "following-sibling" axes SHOULD NOT be
used; however, they MAY be used if document order is not relevant to
the outcome of the expression.
A server is only required to maintain the relative XML document order
of all instances of a particular user-ordered list or leaf-list. The
"preceding-sibling" and "following-sibling" axes MAY be used if they
are evaluated in a context where the context node is a user-ordered
"list" or "leaf-list".
Boucadair & Wu Expires 27 January 2024 [Page 23]
Internet-Draft Guidelines for YANG Documents July 2023
4.6.4. Types
Data nodes that use the "int64" and "uint64" built-in type SHOULD NOT
be used within numeric or boolean expressions. There are boundary
conditions in which the translation from the YANG 64-bit type to an
XPath number can cause incorrect results. Specifically, an XPath
"double" precision floating-point number cannot represent very large
positive or negative 64-bit numbers because it only provides a total
precision of 53 bits. The "int64" and "uint64" data types MAY be
used in numeric expressions if the value can be represented with no
more than 53 bits of precision.
Data modelers need to be careful not to confuse the YANG value space
and the XPath value space. The data types are not the same in both,
and conversion between YANG and XPath data types SHOULD be considered
carefully.
Explicit XPath data type conversions MAY be used (e.g., "string",
"boolean", or "number" functions), instead of implicit XPath data
type conversions.
XPath expressions that contain a literal value representing a YANG
identity SHOULD always include the declared prefix of the module
where the identity is defined.
XPath expressions for "when" statements SHOULD NOT reference the
context node or any descendant nodes of the context node. They MAY
reference descendant nodes if the "when" statement is contained
within an "augment" statement, and the referenced nodes are not
defined within the "augment" statement.
Example:
augment "/rt:active-route/rt:input/rt:destination-address" {
when "rt:address-family='v4ur:ipv4-unicast'" {
description
"This augment is valid only for IPv4 unicast.";
}
// nodes defined here within the augment-stmt
// cannot be referenced in the when-stmt
}
4.6.5. Wildcards
It is possible to construct XPath expressions that will evaluate
differently when combined with several modules within a server
implementation rather than when evaluated within the single module.
This is due to augmenting nodes from other modules.
Boucadair & Wu Expires 27 January 2024 [Page 24]
Internet-Draft Guidelines for YANG Documents July 2023
Wildcard expansion is done within a server against all the nodes from
all namespaces, so it is possible for a "must" or "when" expression
that uses the '*' operator to always evaluate to false if processed
within a single YANG module. In such cases, the "description"
statement SHOULD clarify that augmenting objects are expected to
match the wildcard expansion.
when /foo/services/*/active {
description
"No services directly defined in this module.
Matches objects that have augmented the services container.";
}
4.6.6. Boolean Expressions
The YANG "must" and "when" statements use an XPath boolean expression
to define the test condition for the statement. It is important to
specify these expressions in a way that will not cause inadvertent
changes in the result if the objects referenced in the expression are
updated in future revisions of the module.
For example, the leaf "foo2" must exist if the leaf "foo1" is equal
to "one" or "three":
leaf foo1 {
type enumeration {
enum one;
enum two;
enum three;
}
}
leaf foo2 {
// INCORRECT
must "/f:foo1 != 'two'";
type string;
}
leaf foo2 {
// CORRECT
must "/f:foo1 = 'one' or /f:foo1 = 'three'";
type string;
}
In the next revision of the module, leaf "foo1" is extended with a
new enum named "four":
Boucadair & Wu Expires 27 January 2024 [Page 25]
Internet-Draft Guidelines for YANG Documents July 2023
leaf foo1 {
type enumeration {
enum one;
enum two;
enum three;
enum four;
}
}
Now the first XPath expression will allow the enum "four" to be
accepted in addition to the "one" and "three" enum values.
4.7. YANG Definition Lifecycle Management
The YANG status statement MUST be present within a definition if its
value is "deprecated" or "obsolete". The status SHOULD NOT be
changed from "current" directly to "obsolete". An object SHOULD be
available for at least one year with a "deprecated" status before it
is changed to "obsolete".
The module or submodule name MUST NOT be changed, once the document
containing the module or submodule is published.
The module namespace URI value MUST NOT be changed, once the document
containing the module is published.
The revision date substatement within the import statement SHOULD be
present if any groupings are used from the external module.
The revision date substatement within the include statement SHOULD be
present if any groupings are used from the external submodule.
If an import statement is for a module from a stable source (e.g., an
RFC for an IETF module), then a reference-stmt SHOULD be present
within an import statement.
import ietf-yang-types {
prefix yang;
reference "RFC 6991: Common YANG Data Types";
}
If submodules are used, then the document containing the main module
MUST be updated so that the main module revision date is equal to or
more recent than the revision date of any submodule that is (directly
or indirectly) included by the main module.
Definitions for future use SHOULD NOT be specified in a module. Do
not specify placeholder objects like the "reserved" example below:
Boucadair & Wu Expires 27 January 2024 [Page 26]
Internet-Draft Guidelines for YANG Documents July 2023
leaf reserved {
type string;
description
"This object has no purpose at this time, but a future
revision of this module might define a purpose
for this object.";
}
}
4.8. Module Header, Meta, and Revision Statements
For published modules, the namespace MUST be a globally unique URI,
as defined in [RFC3986]. This value is usually assigned by the IANA.
The "organization" statement MUST be present. If the module is
contained in a document intended for IETF Standards Track status,
then the organization SHOULD be the IETF working group (WG) chartered
to write the document. For other standards organizations, a similar
approach is also suggested.
The "contact" statement MUST be present. If the module is contained
in a document intended for Standards Track status, then the WG web
and mailing information SHOULD be present, and the main document
author or editor contact information SHOULD be present. If
additional authors or editors exist, their contact information MAY be
present. There is no need to include the contact information for WG
Chairs.
The "description" statement MUST be present. For modules published
within IETF documents, the appropriate IETF Trust Copyright text MUST
be present, as described in Section 3.1.
If the module relies on information contained in other documents,
which are not the same documents implied by the import statements
present in the module, then these documents MUST be identified in the
reference statement.
A "revision" statement MUST be present for each published version of
the module. The "revision" statement MUST have a "reference"
substatement. It MUST identify the published document that contains
the module. Modules are often extracted from their original
documents, and it is useful for developers and operators to know how
to find the original source document in a consistent manner. The
"revision" statement MAY have a "description" substatement.
The following example shows the revision statement for a published
YANG module:
Boucadair & Wu Expires 27 January 2024 [Page 27]
Internet-Draft Guidelines for YANG Documents July 2023
revision "2012-02-22" {
description
"Initial version";
reference
"RFC 6536: Network Configuration Protocol (NETCONF)
Access Control Model";
}
For an unpublished module, a complete history of each unpublished
module revision is not required. That is, within a sequence of draft
versions, only the most recent revision need be recorded in the
module. Do not remove or reuse a revision statement for a published
module. A new revision date is not required unless the module
contents have changed. If the module contents have changed, then the
revision date of that new module version MUST be updated to a date
later than that of the previous version.
The following example shows the two revision statements for an
unpublished update to a published YANG module:
revision "2017-12-11" {
description
"Added support for YANG 1.1 actions and notifications tied to
data nodes. Clarify how NACM extensions can be used by other
data models.";
reference
"RFC YYYY: Network Configuration Access Control Model";
}
revision "2012-02-22" {
description
"Initial version";
reference
"RFC 6536: Network Configuration Protocol (NETCONF)
Access Control Model";
}
4.9. Namespace Assignments
It is RECOMMENDED that only valid YANG modules be included in
documents, whether or not the modules are published yet. This
allows:
* the module to compile correctly instead of generating disruptive
fatal errors.
* early implementors to use the modules without picking a random
value for the XML namespace.
Boucadair & Wu Expires 27 January 2024 [Page 28]
Internet-Draft Guidelines for YANG Documents July 2023
* early interoperability testing since independent implementations
will use the same XML namespace value.
Until a URI is assigned by the IANA, a proposed namespace URI MUST be
provided for the namespace statement in a YANG module. A value
SHOULD be selected that is not likely to collide with other YANG
namespaces. Standard module names, prefixes, and URI strings already
listed in the "YANG Module Names" registry MUST NOT be used.
A standard namespace statement value SHOULD have the following form:
:
The following URN prefix string SHOULD be used for published and
unpublished YANG modules:
urn:ietf:params:xml:ns:yang:
The following example URNs would be valid namespace statement values
for Standards Track modules:
urn:ietf:params:xml:ns:yang:ietf-netconf-partial-lock
urn:ietf:params:xml:ns:yang:ietf-netconf-state
urn:ietf:params:xml:ns:yang:ietf-netconf
Note that a different URN prefix string SHOULD be used for modules
that are not Standards Track. The string SHOULD be selected
according to the guidelines in [RFC7950].
The following URIs exemplify what might be used by modules that are
not Standards Track. Note that the domain "example.com" SHOULD be
used by example modules in IETF I-Ds. These URIs are not intended to
be dereferenced. They are used for module namespace identification
only.
Example URIs using URLs per [RFC3986]:
https://example.com/ns/example-interfaces
https://example.com/ns/example-system
Example URIs using tags per [RFC4151]:
tag:example.com,2017:example-interfaces
tag:example.com,2017:example-system
Boucadair & Wu Expires 27 January 2024 [Page 29]
Internet-Draft Guidelines for YANG Documents July 2023
4.10. Top-Level Data Definitions
The top-level data organization SHOULD be considered carefully, in
advance. Data model designers need to consider how the functionality
for a given protocol or protocol family will grow over time.
The separation of configuration data and operational state SHOULD be
considered carefully. It is sometimes useful to define separate top-
level containers for configuration and non-configuration data. For
some existing top-level data nodes, configuration data was not in
scope, so only one container representing operational state was
created. Refer to NMDA [RFC8342] for details.
The number of top-level data nodes within a module SHOULD be
minimized. It is often useful to retrieve related information within
a single subtree. If data is too distributed, it becomes difficult
to retrieve all at once.
The names and data organization SHOULD reflect persistent
information, such as the name of a protocol. The name of the working
group SHOULD NOT be used because this may change over time.
A mandatory database data definition is defined as a node that a
client must provide for the database to be valid. The server is not
required to provide a value.
Top-level database data definitions MUST NOT be mandatory. If a
mandatory node appears at the top level, it will immediately cause
the database to be invalid. This can occur when the server boots or
when a module is loaded dynamically at runtime.
4.11. Data Types
Selection of an appropriate data type (i.e., built-in type, existing
derived type, or new derived type) is very subjective; therefore, few
requirements can be specified on that subject.
Data model designers SHOULD use the most appropriate built-in data
type for the particular application.
The signed numeric data types (i.e., "int8", "int16", "int32", and
"int64") SHOULD NOT be used unless negative values are allowed for
the desired semantics.
Boucadair & Wu Expires 27 January 2024 [Page 30]
Internet-Draft Guidelines for YANG Documents July 2023
4.11.1. Fixed-Value Extensibility
If the set of values is fixed and the data type contents are
controlled by a single naming authority, then an enumeration data
type SHOULD be used.
leaf foo {
type enumeration {
enum one;
enum two;
}
}
If extensibility of enumerated values is required, then the
"identityref" data type SHOULD be used instead of an enumeration or
other built-in type.
identity foo-type {
description "Base for the extensible type";
}
identity one {
base f:foo-type;
}
identity two {
base f:foo-type;
}
leaf foo {
type identityref {
base f:foo-type;
}
}
Note that any module can declare an identity with base "foo-type"
that is valid for the "foo" leaf. Identityref values are considered
to be qualified names.
4.11.2. Patterns and Ranges
For string data types, if a machine-readable pattern can be defined
for the desired semantics, then one or more pattern statements SHOULD
be present. A single-quoted string SHOULD be used to specify the
pattern, since a double-quoted string can modify the content. If the
patterns used in a type definition have known limitations such as
false negative or false positive matches, then these limitations
SHOULD be documented within the typedef or data definition.
Boucadair & Wu Expires 27 January 2024 [Page 31]
Internet-Draft Guidelines for YANG Documents July 2023
The following typedef from [RFC6991] demonstrates the proper use of
the "pattern" statement:
typedef ipv4-address-no-zone {
type inet:ipv4-address {
pattern '[0-9\.]*';
}
...
}
For string data types, if the length of the string is required to be
bounded in all implementations, then a length statement MUST be
present.
The following typedef from [RFC6991] demonstrates the proper use of
the "length" statement:
typedef yang-identifier {
type string {
length "1..max";
pattern '[a-zA-Z_][a-zA-Z0-9\-_.]*';
pattern '.|..|[^xX].*|.[^mM].*|..[^lL].*';
}
...
}
For numeric data types, if the values allowed by the intended
semantics are different than those allowed by the unbounded intrinsic
data type (e.g., "int32"), then a range statement SHOULD be present.
The following typedef from [RFC6991] demonstrates the proper use of
the "range" statement:
typedef dscp {
type uint8 {
range "0..63";
}
...
}
4.11.3. Enumerations and Bits
For "enumeration" or "bits" data types, the semantics for each "enum"
or "bit" SHOULD be documented. A separate "description" statement
(within each "enum" or "bit" statement) SHOULD be present.
Boucadair & Wu Expires 27 January 2024 [Page 32]
Internet-Draft Guidelines for YANG Documents July 2023
leaf foo {
// INCORRECT
type enumeration {
enum one;
enum two;
}
description
"The foo enum...
one: The first enum
two: The second enum";
}
leaf foo {
// CORRECT
type enumeration {
enum one {
description "The first enum";
}
enum two {
description "The second enum";
}
}
description
"The foo enum... ";
}
4.11.4. Union Types
The YANG "union" type is evaluated by testing a value against each
member type in the union. The first type definition that accepts a
value as valid is the member type used. In general, member types
SHOULD be ordered from most restrictive to least restrictive types.
In the following example, the "enumeration" type will never be
matched because the preceding "string" type will match everything.
Incorrect:
type union {
type string;
type enumeration {
enum up;
enum down;
}
}
Correct:
Boucadair & Wu Expires 27 January 2024 [Page 33]
Internet-Draft Guidelines for YANG Documents July 2023
type union {
type enumeration {
enum up;
enum down;
}
type string;
}
It is possible for different member types to match, depending on the
input encoding format. In XML, all values are passed as string
nodes; but in JSON, there are different value types for numbers,
booleans, and strings.
In the following example, a JSON numeric value will always be matched
by the "int32" type, but in XML the string value representing a
number will be matched by the "string" type. The second version will
match the "int32" member type no matter how the input is encoded.
Incorrect:
type union {
type string;
type int32;
}
Correct:
type union {
type int32;
type string;
}
4.11.5. Empty and Boolean
YANG provides an "empty" data type, which has one value (i.e.,
present). The default is "not present", which is not actually a
value. When used within a list key, only one value can (and must)
exist for this key leaf. The type "empty" SHOULD NOT be used for a
key leaf since it is pointless.
There is really no difference between a leaf of type "empty" and a
leaf-list of type "empty". Both are limited to one instance. The
type "empty" SHOULD NOT be used for a leaf-list.
The advantage of using type "empty" instead of type "boolean" is that
the default (not present) does not take up any bytes in a
representation. The disadvantage is that the client may not be sure
if an empty leaf is missing because it was filtered somehow or not
Boucadair & Wu Expires 27 January 2024 [Page 34]
Internet-Draft Guidelines for YANG Documents July 2023
implemented. The client may not have a complete and accurate schema
for the data returned by the server and may not be aware of the
missing leaf.
The YANG "boolean" data type provides two values ("true" and
"false"). When used within a list key, two entries can exist for
this key leaf. Default values are ignored for key leafs, but a
default statement is often used for plain boolean leafs. The
advantage of the "boolean" type is that the leaf or leaf-list has a
clear representation for both values. The default value is usually
not returned unless explicitly requested by the client, so no bytes
are used in a typical representation.
In general, the "boolean" data type SHOULD be used instead of the
"empty" data type, as shown in the example below:
Incorrect:
leaf flag1 {
type empty;
}
Correct:
leaf flag2 {
type boolean;
default false;
}
4.12. Reusable Type Definitions
If an appropriate derived type exists in any standard module, such as
[RFC6991], then it SHOULD be used instead of defining a new derived
type.
If an appropriate units identifier can be associated with the desired
semantics, then a units statement SHOULD be present.
If an appropriate default value can be associated with the desired
semantics, then a default statement SHOULD be present.
If a significant number of derived types are defined, and it is
anticipated that these data types will be reused by multiple modules,
then these derived types SHOULD be contained in a separate module or
submodule, to allow easier reuse without unnecessary coupling.
The "description" statement MUST be present.
Boucadair & Wu Expires 27 January 2024 [Page 35]
Internet-Draft Guidelines for YANG Documents July 2023
If the type definition semantics are defined in an external document
(other than another YANG module indicated by an import statement),
then the reference statement MUST be present.
4.13. Reusable Groupings
A reusable grouping is a YANG grouping that can be imported by
another module and is intended for use by other modules. This is not
the same as a grouping that is used within the module in which it is
defined, but it happens to be exportable to another module because it
is defined at the top level of the YANG module.
The following guidelines apply to reusable groupings, in order to
make them as robust as possible:
* Clearly identify the purpose of the grouping in the "description"
statement.
* There are five different XPath contexts in YANG (rpc/input, rpc/
output, notification, "config true" data nodes, and all data
nodes). Clearly identify which XPath contexts are applicable or
excluded for the grouping.
* Do not reference data outside the grouping in any "path", "must",
or "when" statements.
* Do not include a "default" substatement on a leaf or choice unless
the value applies on all possible contexts.
* Do not include a "config" substatement on a data node unless the
value applies on all possible contexts.
* Clearly identify any external dependencies in the grouping
"description" statement, such as nodes referenced by an absolute
path from a "path", "must", or "when" statement.
4.14. Data Definitions
The "description" statement MUST be present in the following YANG
statements:
* anyxml
* augment
* choice
* container
Boucadair & Wu Expires 27 January 2024 [Page 36]
Internet-Draft Guidelines for YANG Documents July 2023
* extension
* feature
* grouping
* identity
* leaf
* leaf-list
* list
* notification
* rpc
* typedef
If the data definition semantics are defined in an external document,
(other than another YANG module indicated by an import statement),
then a reference statement MUST be present.
The "anyxml" construct may be useful to represent an HTML banner
containing markup elements, such as "" and "", and MAY be used
in such cases. However, this construct SHOULD NOT be used if other
YANG data node types can be used instead to represent the desired
syntax and semantics.
It has been found that the "anyxml" statement is not implemented
consistently across all servers. It is possible that mixed-mode XML
will not be supported or that configuration anyxml nodes will not
supported.
If there are referential integrity constraints associated with the
desired semantics that can be represented with XPath, then one or
more "must" statements SHOULD be present.
For list and leaf-list data definitions, if the number of possible
instances is required to be bounded for all implementations, then the
max-elements statements SHOULD be present.
If any "must" or "when" statements are used within the data
definition, then the data definition "description" statement SHOULD
describe the purpose of each one.
Boucadair & Wu Expires 27 January 2024 [Page 37]
Internet-Draft Guidelines for YANG Documents July 2023
The "choice" statement is allowed to be directly present within a
"case" statement in YANG 1.1. This needs to be considered carefully.
Consider simply including the nested "choice" as additional "case"
statements within the parent "choice" statement. Note that the
"mandatory" and "default" statements within a nested "choice"
statement only apply if the "case" containing the nested "choice"
statement is first selected.
If a list defines any key leafs, then these leafs SHOULD be defined
in order, as the first child nodes within the list. The key leafs
MAY be in a different order in some cases, e.g., they are defined in
a grouping, and not inline in the list statement.
4.14.1. Non-Presence Containers
A non-presence container is used to organize data into specific
subtrees. It is not intended to have semantics within the data model
beyond this purpose, although YANG allows it (e.g., a "must"
statement within the non-presence container).
Example using container wrappers:
container top {
container foos {
list foo { ... }
}
container bars {
list bar { ... }
}
}
Example without container wrappers:
container top {
list foo { ... }
list bar { ... }
}
Use of non-presence containers to organize data is a subjective
matter similar to use of subdirectories in a file system. Although
these containers do not have any semantics, they can impact protocol
operations for the descendant data nodes within a non-presence
container, so use of these containers SHOULD be considered carefully.
The NETCONF and RESTCONF protocols do not currently support the
ability to delete all list (or leaf-list) entries at once. This
deficiency is sometimes avoided by use of a parent container (i.e.,
deleting the container also removes all child entries).
Boucadair & Wu Expires 27 January 2024 [Page 38]
Internet-Draft Guidelines for YANG Documents July 2023
4.14.2. Top-Level Data Nodes
Use of top-level objects needs to be considered carefully:
* top-level siblings are not ordered
* top-level siblings are not static and depend on the modules that
are loaded
* for subtree filtering, retrieval of a top-level leaf-list will be
treated as a content-match node for all top-level-siblings
* a top-level list with many instances may impact performance
4.15. Operation Definitions
If the operation semantics are defined in an external document (other
than another YANG module indicated by an import statement), then a
reference statement MUST be present.
If the operation impacts system behavior in some way, it SHOULD be
mentioned in the "description" statement.
If the operation is potentially harmful to system behavior in some
way, it MUST be mentioned in the Security Considerations section of
the document.
4.16. Notification Definitions
The "description" statement MUST be present.
If the notification semantics are defined in an external document
(other than another YANG module indicated by an import statement),
then a reference statement MUST be present.
If the notification refers to a specific resource instance, then this
instance SHOULD be identified in the notification data. This is
usually done by including "leafref" leaf nodes with the key leaf
values for the resource instance. For example:
notification interface-up {
description "Sent when an interface is activated.";
leaf name {
type leafref {
path "/if:interfaces/if:interface/if:name";
}
}
}
Boucadair & Wu Expires 27 January 2024 [Page 39]
Internet-Draft Guidelines for YANG Documents July 2023
Note that there are no formal YANG statements to identify any data
node resources associated with a notification. The "description"
statement for the notification SHOULD specify if and how the
notification identifies any data node resources associated with the
specific event.
4.17. Feature Definitions
The YANG "feature" statement is used to define a label for a set of
optional functionality within a module. The "if-feature" statement
is used in the YANG statements associated with a feature. The
description-stmt within a feature-stmt MUST specify any interactions
with other features.
The set of YANG features defined in a module should be considered
carefully. Very fine granular features increase interoperability
complexity and should be avoided. A likely misuse of the feature
mechanism is the tagging of individual leafs (e.g., counters) with
separate features.
If there is a large set of objects associated with a YANG feature,
then consider moving those objects to a separate module, instead of
using a YANG feature. Note that the set of features within a module
is easily discovered by the reader, but the set of related modules
within the entire YANG library is not as easy to identify. Module
names with a common prefix can help readers identify the set of
related modules, but this assumes the reader will have discovered and
installed all the relevant modules.
Another consideration for deciding whether to create a new module or
add a YANG feature is the stability of the module in question. It
may be desirable to have a stable base module that is not changed
frequently. If new functionality is placed in a separate module,
then the base module does not need to be republished. If it is
designed as a YANG feature, then the module will need to be
republished.
If one feature requires implementation of another feature, then an
"if-feature" statement SHOULD be used in the dependent "feature"
statement.
For example, feature2 requires implementation of feature1:
Boucadair & Wu Expires 27 January 2024 [Page 40]
Internet-Draft Guidelines for YANG Documents July 2023
feature feature1 {
description "Some protocol feature";
}
feature feature2 {
if-feature "feature1";
description "Another protocol feature";
}
4.18. YANG Data Node Constraints
4.18.1. Controlling Quantity
The "min-elements" and "max-elements" statements can be used to
control how many list or leaf-list instances are required for a
particular data node. YANG constraint statements SHOULD be used to
identify conditions that apply to all implementations of the data
model. If platform-specific limitations (e.g., the "max-elements"
supported for a particular list) are relevant to operations, then a
data model definition statement (e.g., "max-ports" leaf) SHOULD be
used to identify the limit.
4.18.2. "must" versus "when"
"must" and "when" YANG statements are used to provide cross-object
referential tests. They have very different behavior. The "when"
statement causes data node instances to be silently deleted as soon
as the condition becomes false. A false "when" expression is not
considered to be an error.
The "when" statement SHOULD be used together with "augment" or "uses"
statements to achieve conditional model composition. The condition
SHOULD be based on static properties of the augmented entry (e.g.,
list key leafs).
The "must" statement causes a datastore validation error if the
condition is false. This statement SHOULD be used for enforcing
parameter value restrictions that involve more than one data node
(e.g., end-time parameter must be after the start-time parameter).
4.19. "augment" Statements
The YANG "augment" statement is used to define a set of data
definition statements that will be added as child nodes of a target
data node. The module namespace for these data nodes will be the
augmenting module, not the augmented module.
Boucadair & Wu Expires 27 January 2024 [Page 41]
Internet-Draft Guidelines for YANG Documents July 2023
A top-level "augment" statement SHOULD NOT be used if the target data
node is in the same module or submodule as the evaluated "augment"
statement. The data definition statements SHOULD be added inline
instead.
4.19.1. Conditional Augment Statements
The "augment" statement is often used together with the "when"
statement and/or "if-feature" statement to make the augmentation
conditional on some portion of the data model.
The following example from [RFC7223] shows how a conditional
container called "ethernet" is added to the "interface" list only for
entries of the type "ethernetCsmacd".
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:ethernetCsmacd'";
container ethernet {
leaf duplex {
...
}
}
}
4.19.2. Conditionally Mandatory Data Definition Statements
YANG has very specific rules about how configuration data can be
updated in new releases of a module. These rules allow an "old
client" to continue interoperating with a "new server".
If data nodes are added to an existing entry, the old client MUST NOT
be required to provide any mandatory parameters that were not in the
original module definition.
It is possible to add conditional "augment" statements such that the
old client would not know about the new condition and would not
specify the new condition. The conditional "augment" statement can
contain mandatory objects only if the condition is false, unless
explicitly requested by the client.
Only a conditional "augment" statement that uses the "when" statement
form of a condition can be used in this manner. The YANG features
enabled on the server cannot be controlled by the client in any way,
so it is not safe to add mandatory augmenting data nodes based on the
"if-feature" statement.
Boucadair & Wu Expires 27 January 2024 [Page 42]
Internet-Draft Guidelines for YANG Documents July 2023
The XPath "when" statement condition MUST NOT reference data outside
of the target data node because the client does not have any control
over this external data.
In the following dummy example, it is okay to augment the "interface"
entry with "mandatory-leaf" because the augmentation depends on
support for "some-new-iftype". The old client does not know about
this type, so it would never select this type; therefore, it would
not add a mandatory data node.
module example-module {
yang-version 1.1;
namespace "tag:example.com,2017:example-module";
prefix mymod;
import iana-if-type { prefix iana; }
import ietf-interfaces { prefix if; }
identity some-new-iftype {
base iana:iana-interface-type;
}
augment "/if:interfaces/if:interface" {
when "if:type = 'mymod:some-new-iftype'";
leaf mandatory-leaf {
type string;
mandatory true;
}
}
}
Note that this practice is safe only for creating data resources. It
is not safe for replacing or modifying resources if the client does
not know about the new condition. The YANG data model MUST be
packaged in a way that requires the client to be aware of the
mandatory data nodes if it is aware of the condition for this data.
In the example above, the "some-new-iftype" identity is defined in
the same module as the "mandatory-leaf" data definition statement.
This practice is not safe for identities defined in a common module
such as "iana-if-type" because the client is not required to know
about "my-module" just because it knows about the "iana-if-type"
module.
Boucadair & Wu Expires 27 January 2024 [Page 43]
Internet-Draft Guidelines for YANG Documents July 2023
4.20. Deviation Statements
Per RFC 7950, Section 7.20.3, the YANG "deviation" statement is not
allowed to appear in IETF YANG modules, but it can be useful for
documenting server capabilities. Deviation statements are not
reusable and typically not shared across all platforms.
There are several reasons that deviations might be needed in an
implementation, e.g., an object cannot be supported on all platforms,
or feature delivery is done in multiple development phases.
Deviation statements can also be used to add annotations to a module,
which does not affect the conformance requirements for the module.
It is suggested that deviation statements be defined in separate
modules from regular YANG definitions. This allows the deviations to
be platform specific and/or temporary.
The order that deviation statements are evaluated can affect the
result. Therefore, multiple deviation statements in the same module,
for the same target object, SHOULD NOT be used.
The "max-elements" statement is intended to describe an architectural
limit to the number of list entries. It is not intended to describe
platform limitations. It is better to use a "deviation" statement
for the platforms that have a hard resource limit.
Example documenting platform resource limits:
Wrong: (max-elements in the list itself)
container backups {
list backup {
...
max-elements 10;
...
}
}
Correct: (max-elements in a deviation)
deviation /bk:backups/bk:backup {
deviate add {
max-elements 10;
}
}
Boucadair & Wu Expires 27 January 2024 [Page 44]
Internet-Draft Guidelines for YANG Documents July 2023
4.21. Extension Statements
The YANG "extension" statement is used to specify external
definitions. This appears in the YANG syntax as an "unknown-
statement". Usage of extension statements in a published module
needs to be considered carefully.
The following guidelines apply to the usage of YANG extensions:
* The semantics of the extension MUST NOT contradict any YANG
statements. Extensions can add semantics not covered by the
normal YANG statements.
* The module containing the extension statement MUST clearly
identify the conformance requirements for the extension. It
should be clear whether all implementations of the YANG module
containing the extension need to also implement the extension. If
not, identify what conditions apply that would require
implementation of the extension.
* The extension MUST clearly identify where it can be used within
other YANG statements.
* The extension MUST clearly identify if YANG statements or other
extensions are allowed or required within the extension as
substatements.
4.22. Data Correlation
Data can be correlated in various ways, using common data types,
common data naming, and common data organization. There are several
ways to extend the functionality of a module, based on the degree of
coupling between the old and new functionality:
inline: update the module with new protocol-accessible objects. The
naming and data organization of the original objects is used. The
new objects are in the original module namespace.
augment: create a new module with new protocol-accessible objects
that augment the original data structure. The naming and data
organization of the original objects is used. The new objects are
in the new module namespace.
mirror: create new objects in a new module or the original module,
except use a new naming scheme and data location. The naming can
be coupled in different ways. Tight coupling is achieved with a
"leafref" data type, with the "require-instance" substatement set
to "true". This method SHOULD be used.
Boucadair & Wu Expires 27 January 2024 [Page 45]
Internet-Draft Guidelines for YANG Documents July 2023
If the new data instances are not limited to the values in use in the
original data structure, then the "require-instance" substatement
MUST be set to "false". Loose coupling is achieved by using key
leafs with the same data type as the original data structure. This
has the same semantics as setting the "require-instance" substatement
to "false".
The relationship between configuration and operational state has been
clarified in NMDA [RFC8342].
4.22.1. Use of "leafref" for Key Correlation
Sometimes it is not practical to augment a data structure. For
example, the correlated data could have different keys or contain
mandatory nodes.
The following example shows the use of the "leafref" data type for
data correlation purposes:
Not preferred:
list foo {
key name;
leaf name {
type string;
}
...
}
list foo-addon {
key name;
config false;
leaf name {
type string;
}
...
}
Preferred:
Boucadair & Wu Expires 27 January 2024 [Page 46]
Internet-Draft Guidelines for YANG Documents July 2023
list foo {
key name;
leaf name {
type string;
}
...
}
list foo-addon {
key name;
config false;
leaf name {
type leafref {
path "/foo/name";
require-instance false;
}
}
leaf addon {
type string;
mandatory true;
}
}
4.23. Operational State
The modeling of operational state with YANG has been refined over
time. At first, only data that has a "config" statement value of
"false" was considered to be operational state. This data was not
considered to be part of any datastore, which made the YANG XPath
definition much more complicated.
Operational state is now modeled using YANG according to the new NMDA
[RFC8342] and conceptually contained in the operational state
datastore, which also includes the operational values of
configuration data. There is no longer any need to duplicate data
structures to provide separate configuration and operational state
sections.
This section describes some data modeling issues related to
operational state and guidelines for transitioning YANG data model
design to be NMDA compatible.
Boucadair & Wu Expires 27 January 2024 [Page 47]
Internet-Draft Guidelines for YANG Documents July 2023
4.23.1. Combining Operational State and Configuration Data
If possible, operational state SHOULD be combined with its associated
configuration data. This prevents duplication of key leafs and
ancestor nodes. It also prevents race conditions for retrieval of
dynamic entries and allows configuration and operational state to be
retrieved together with minimal message overhead.
container foo {
...
// contains "config true" and "config false" nodes that have
// no corresponding "config true" object (e.g., counters)
}
4.23.2. Representing Operational Values of Configuration Data
If possible, the same data type SHOULD be used to represent the
configured value and the operational value, for a given leaf or leaf-
list object.
Sometimes the configured value set is different than the operational
value set for that object, for example, the "admin-status" and "oper-
status" leafs in [RFC8343]. In this case, a separate object MAY be
used to represent the configured and operational values.
Sometimes the list keys are not identical for configuration data and
the corresponding operational state. In this case, separate lists
MAY be used to represent the configured and operational values.
If it is not possible to combine configuration and operational state,
then the keys used to represent list entries SHOULD be the same type.
The "leafref" data type SHOULD be used in operational state for key
leafs that have corresponding configuration instances. The "require-
instance" statement MAY be set to "false" (in YANG 1.1 modules only)
to indicate instances are allowed in the operational state that do
not exist in the associated configuration data.
The need to replicate objects or define different operational state
objects depends on the data model. It is not possible to define one
approach that will be optimal for all data models.
Designers SHOULD describe and justify any NMDA exceptions in detail,
such as the use of separate subtrees and/or separate leafs. The
"description" statements for both the configuration and the
operational state SHOULD be used for this purpose.
Boucadair & Wu Expires 27 January 2024 [Page 48]
Internet-Draft Guidelines for YANG Documents July 2023
4.23.3. NMDA Transition Guidelines
YANG modules SHOULD be designed with the assumption that they will be
used on servers supporting the operational state datastore. With
this in mind, YANG modules SHOULD define "config false" nodes
wherever they make sense to the data model. "Config false" nodes
SHOULD NOT be defined to provide the operational value for
configuration nodes, except when the value space of a configured and
operational value may differ, in which case a distinct "config false"
node SHOULD be defined to hold the operational value for the
configured node.
The following guidelines are meant to help modelers develop YANG
modules that will maximize the utility of the model with both current
and new implementations.
New modules and modules that are not concerned with the operational
state of configuration information SHOULD immediately be structured
to be NMDA compatible, as described in Section 4.23.1. This
transition MAY be deferred if the module does not contain any
configuration datastore objects.
The remaining are options that MAY be followed during the time that
NMDA mechanisms are being defined.
(a) Modules that require immediate support for the NMDA features
SHOULD be structured for NMDA. A temporary non-NMDA version of
this type of module MAY exist, as either an existing model or a
model created by hand or with suitable tools that mirror the
current modeling strategies. Both the NMDA and the non-NMDA
modules SHOULD be published in the same document, with NMDA
modules in the document main body and the non-NMDA modules in a
non-normative appendix. The use of the non-NMDA module will
allow temporary bridging of the time period until NMDA
implementations are available.
(b) For published models, the model should be republished with an
NMDA-compatible structure, deprecating non-NMDA constructs. For
example, the "ietf-interfaces" model in [RFC7223] has been
restructured as an NMDA-compatible model in [RFC8343]. The
"/interfaces-state" hierarchy has been marked "status
deprecated". Models that mark their "/foo-state" hierarchy with
"status deprecated" will allow NMDA-capable implementations to
avoid the cost of duplicating the state nodes, while enabling
non-NMDA-capable implementations to utilize them for access to
the operational values.
Boucadair & Wu Expires 27 January 2024 [Page 49]
Internet-Draft Guidelines for YANG Documents July 2023
(c) For models that augment models that have not been structured
with the NMDA, the modeler will have to consider the structure
of the base model and the guidelines listed above. Where
possible, such models should move to new revisions of the base
model that are NMDA compatible. When that is not possible,
augmenting "state" containers SHOULD be avoided, with the
expectation that the base model will be re-released with the
state containers marked as deprecated. It is RECOMMENDED to
augment only the "/foo" hierarchy of the base model. Where this
recommendation cannot be followed, then any new "state" elements
SHOULD be included in their own module.
4.23.3.1. Temporary Non-NMDA Modules
A temporary non-NMDA module allows a non-NMDA-aware client to access
operational state from an NMDA-compliant server. It contains the
top-level "config false" data nodes that would have been defined in a
legacy YANG module (before NMDA).
A server that needs to support both NMDA and non-NMDA clients can
advertise both the new NMDA module and the temporary non-NMDA module.
A non-NMDA client can use separate "foo" and "foo-state" subtrees,
except the "foo-state" subtree is located in a different (temporary)
module. The NMDA module can be used by a non-NMDA client to access
the conventional configuration datastores and the deprecated
operation to access nested "config false" data nodes.
To create the temporary non-NMDA model from an NMDA model, the
following steps can be taken:
* Change the module name by appending "-state" to the original
module name
* Change the namespace by appending "-state" to the original
namespace value
* Change the prefix by appending "-s" to the original prefix value
* Add an import to the original module (e.g., for typedef
definitions)
* Retain or create only the top-level nodes that have a "config"
statement value "false". These subtrees represent "config false"
data nodes that were combined into the configuration subtree;
therefore, they are not available to non-NMDA aware clients. Set
the "status" statement to "deprecated" for each new node.
Boucadair & Wu Expires 27 January 2024 [Page 50]
Internet-Draft Guidelines for YANG Documents July 2023
* The module description SHOULD clearly identify the module as a
temporary non-NMDA module
4.23.3.2. Example: Create a New NMDA Module
Create an NMDA-compliant module, using combined configuration and
state subtrees, whenever possible.
module example-foo {
namespace "urn:example.com:params:xml:ns:yang:example-foo";
prefix "foo";
container foo {
// configuration data child nodes
// operational value in operational state datastore only
// may contain "config false" nodes as needed
}
}
4.23.3.3. Example: Convert an Old Non-NMDA Module
Do not remove non-compliant objects from existing modules. Instead,
change the status to "deprecated". At some point, usually after 1
year, the status MAY be changed to "obsolete".
Old Module:
module example-foo {
namespace "urn:example.com:params:xml:ns:yang:example-foo";
prefix "foo";
container foo {
// configuration data child nodes
}
container foo-state {
config false;
// operational state child nodes
}
}
Converted NMDA Module:
Boucadair & Wu Expires 27 January 2024 [Page 51]
Internet-Draft Guidelines for YANG Documents July 2023
module example-foo {
namespace "urn:example.com:params:xml:ns:yang:example-foo";
prefix "foo";
container foo {
// configuration data child nodes
// operational value in operational state datastore only
// may contain "config false" nodes as needed
// will contain any data nodes from old foo-state
}
// keep original foo-state but change status to deprecated
container foo-state {
config false;
status deprecated;
// operational state child nodes
}
}
4.23.3.4. Example: Create a Temporary NMDA Module
Create a new module that contains the top-level operational state
data nodes that would have been available before they were combined
with configuration data nodes (to be NMDA compliant).
module example-foo-state {
namespace "urn:example.com:params:xml:ns:yang:example-foo-state";
prefix "foo-s";
// import new or converted module; not used in this example
import example-foo { prefix foo; }
container foo-state {
config false;
status deprecated;
// operational state child nodes
}
}
4.24. Performance Considerations
It is generally likely that certain YANG statements require more
runtime resources than other statements. Although there are no
performance requirements for YANG validation, the following
information MAY be considered when designing YANG data models:
* Lists are generally more expensive than containers
Boucadair & Wu Expires 27 January 2024 [Page 52]
Internet-Draft Guidelines for YANG Documents July 2023
* "when" statement evaluation is generally more expensive than "if-
feature" or "choice" statements
* "must" statements are generally more expensive than "min-entries",
"max-entries", "mandatory", or "unique" statements
* "identityref" leafs are generally more expensive than
"enumeration" leafs
* "leafref" and "instance-identifier" types with "require-instance"
set to true are generally more expensive than if "require-
instance" is set to false
4.25. Open Systems Considerations
Only the modules imported by a particular module can be assumed to be
present in an implementation. An open system MAY include any
combination of YANG modules.
4.26. Guidelines for Constructs Specific to YANG 1.1
The set of guidelines for YANG 1.1 will grow as operational
experience is gained with the new language features. This section
contains an initial set of guidelines for new YANG 1.1 language
features.
4.26.1. Importing Multiple Revisions
Standard modules SHOULD NOT import multiple revisions of the same
module into a module. This MAY be done if independent definitions
(e.g., enumeration typedefs) from specific revisions are needed in
the importing module.
4.26.2. Using Feature Logic
The YANG 1.1 feature logic is much more expressive than YANG 1.0. A
"description" statement SHOULD describe the "if-feature" logic in
text, to help readers understand the module.
YANG features SHOULD be used instead of the "when" statement, if
possible. Features are advertised by the server, and objects
conditional by the "if-feature" statement are conceptually grouped
together. There is no such commonality supported for "when"
statements.
Boucadair & Wu Expires 27 January 2024 [Page 53]
Internet-Draft Guidelines for YANG Documents July 2023
Features generally require less server implementation complexity and
runtime resources than objects that use "when" statements. Features
are generally static (i.e., set when a module is loaded and not
changed at runtime). However, every client edit might cause a "when"
statement result to change.
4.26.3. "anyxml" versus "anydata"
The "anyxml" statement MUST NOT be used to represent a conceptual
subtree of YANG data nodes. The "anydata" statement MUST be used for
this purpose.
4.26.4. "action" versus "rpc"
The use of "action" statements or "rpc" statements is a subjective
design decision. RPC operations are not associated with any
particular data node. Actions are associated with a specific data
node definition. An "action" statement SHOULD be used if the
protocol operation is specific to a subset of all data nodes instead
of all possible data nodes.
The same action name MAY be used in different definitions within
different data node. For example, a "reset" action defined with a
data node definition for an interface might have different parameters
than for a power supply or a VLAN. The same action name SHOULD be
used to represent similar semantics.
The NETCONF Access Control Model (NACM) [RFC8341] does not support
parameter-based access control for RPC operations. The user is given
permission (or not) to invoke the RPC operation with any parameters.
For example, if each client is only allowed to reset their own
interface, then NACM cannot be used.
For example, NACM cannot enforce access control based on the value of
the "interface" parameter, only the "reset" operation itself:
rpc reset {
input {
leaf interface {
type if:interface-ref;
mandatory true;
description "The interface to reset.";
}
}
}
Boucadair & Wu Expires 27 January 2024 [Page 54]
Internet-Draft Guidelines for YANG Documents July 2023
However, NACM can enforce access control for individual interface
instances, using a "reset" action. If the user does not have read
access to the specific "interface" instance, then it cannot invoke
the "reset" action for that interface instance:
container interfaces {
list interface {
...
action reset { }
}
}
4.27. Updating YANG Modules (Published versus Unpublished)
YANG modules can change over time. Typically, new data model
definitions are needed to support new features. YANG update rules
defined in Section 11 of [RFC7950] MUST be followed for published
modules. They MAY be followed for unpublished modules.
The YANG update rules only apply to published module revisions. Each
organization will have their own way to identify published work that
is considered to be stable and unpublished work that is considered to
be unstable. For example, in the IETF, the RFC document is used for
published work, and the I-D is used for unpublished work.
5. IANA-Maintained Modules
5.1. Context
IANA maintains a set of registries that are key for interoperability.
The content of these registries are usually available using various
formats (e.g., plain text, XML). However, there were some confusion
in the past about whether the content of some registries is dependent
on a specific representation format. For example, Section 5 of
[RFC8892] was published to clarify that MIB and YANG modules are
merely additional formats in which the "Interface Types (ifType)" and
"Tunnel Types (tunnelType)" registries are available. The MIB
[RFC2863] and YANG modules [RFC7224][RFC8675] are not separate
registries, and the same values are always present in all formats of
the same registry.
Also, some YANG modules include parameters and values directly in a
module that is not maintained by IANA while these are populated in an
IANA registry. Such a design is suboptimal as it creates another
source of information that may deviate from the IANA registry as new
values are assigned or some values are deprecated.
Boucadair & Wu Expires 27 January 2024 [Page 55]
Internet-Draft Guidelines for YANG Documents July 2023
For the sake of consistency, better flexibility to support new
values, and maintaining IANA registries as the unique authoritative
source of information, when such an information is maintained in a
registry, this document encourages the use of IANA-maintained
modules.
The following section provides a set of guidelines for YANG module
authors related to the design of IANA-maintained modules. These
guidelines are meant to leverage existing IANA registries and use
YANG as another format to present the content of these registries
when appropriate.
5.2. Guidelines for IANA-Maintained Modules
When designing a YANG module for a functionality governed by a
protocol for which IANA maintains a registry, it is RECOMMENDED to
specify an IANA-maintained module that echoes the content of that
registry. This is superior to including that content in an IETF-
maintained module.
When one or multiple sub-registries are available under the same
registry, it is RECOMMENDED to define an IANA-maintained module for
each sub-registry. However, module designers MAY consider defining
one single IANA-maintained module that covers all sub-registries if
maintaining that single module is manageable (e.g., very few values
are present or expected to be present for each sub-registry). An
example of such a module is documented in Section 5.2 of [RFC9132].
An IANA-maintained module may use identities (e.g., [RFC8675]) or
enumerations (e.g., [RFC9108]). The decision about which type to use
is left to the module designers and should be made based upon
specifics related to the intended use of the IANA-maintained module.
For example, identities are useful if the registry entries are
organized hierarchically, possibly including multiple inheritances.
It is RECOMMENDED that the reasoning for the design choice is
documented in the companion specification that registers an IANA-
maintained module. For example, [RFC9244] defines an IANA-maintained
module that uses enumerations for the following reason:
"The DOTS telemetry module (Section 10.1) uses "enumerations" rather
than "identities" to define units, samples, and intervals because
otherwise the namespace identifier "ietf-dots-telemetry" must be
included when a telemetry attribute is included (e.g., in a
mitigation efficacy update). The use of "identities" is thus
suboptimal from a message compactness standpoint; one of the key
requirements for DOTS messages."
Boucadair & Wu Expires 27 January 2024 [Page 56]
Internet-Draft Guidelines for YANG Documents July 2023
Designers of IANA-maintained modules MAY supply the full initial
version of the module in a specification document that registers the
module or only a script to be used (including by IANA) for generating
the module (e.g., an XSLT stylesheet as in Appendix A of [RFC9108]).
For both cases, the document that defines an IANA-maintained module
MUST include a note indicating that the document is only documenting
the initial version of the module and that the authoritative version
is to be retrieved from the IANA registry. It is RECOMMENDED to
include the URL from where to retrieve the recent version of the
module. When a script is used, the Internet-Draft that defines an
IANA-maintained module SHOULD include an appendix with the initial
full version of the module. Including such an appendix in pre-RFC
versions is meant to assess the correctness of the outcome of the
supplied script. The authors MUST include a note to the RFC Editor
requesting that the appendix be removed before publication as RFC.
Initial versions of IANA-maintained modules that are published in
RFCs may be misused despite the appropriate language to refer to the
IANA registry to retrieve the up-to-date module. This is problematic
for interoperability, e.g., when values are deprecated or are
associated with a new meaning.
Note: [Style] provides XSLT 1.0 stylesheets and other tools for
translating IANA registries to YANG modules. The tools can be
used to generate up-to-date revisions of an IANA-maintained module
based upon the XML representation of an IANA registry.
If an IANA-maintained module is imported by another module, a
normative reference with the IANA URL from where to retrieve the
IANA-maintained module SHOULD be included. Although not encouraged,
referencing the RFC that defines the initial version of the IANA
module is acceptable in specific cases (e.g., the imported version is
specifically the initial version, the RFC includes useful description
about the usage of the module).
Examples of IANA URLs from where to retrieve the latest version of an
IANA-maintained module are: [IANA_BGP-L2_URL], [IANA_PW-Types_URL],
and [IANA_BFD_URL]. [IANA_FOO_URL] is used in the following to refer
to such URLs. These URLs are expected to be sufficiently permanent
and stable.
Boucadair & Wu Expires 27 January 2024 [Page 57]
Internet-Draft Guidelines for YANG Documents July 2023
5.3. Guidance for Writing the IANA Considerations for RFCs Defining
IANA-Maintained Modules
In addition to the IANA considerations in Section 3.8, the IANA
Considerations Section of an RFC that includes an IANA- maintained
module MUST provide the required instructions for IANA to
automatically perform the maintenance of that IANA module. These
instructions describe how to proceed with updates to the IANA-
maintained module that are triggered by a change to the authoritative
registry. Concretely, the IANA Considerations Section SHALL at least
provide the following information:
* An IANA request to add a note to the page displaying the
information about the IANA-maintained module that new values must
not be directly added to the module, but to an authoritative IANA
registry.
* An IANA request to add a note to the authoritative IANA registry
to indicate that any change to the registry must be reflected into
the corresponding IANA-maintained module.
* Details about the required actions (e.g., add a new "identity" or
"enum" statement) to update the IANA-maintained module to reflect
changes to an authoritative IANA registry. Typically, these
details have to include the procedure to create a new "identity"
statement name and sub-statements ("base", "status",
"description", and "reference") or a new "enum" statement and sub-
statements ("value", "status", "description", and "reference").
* A note that unassigned or reserved values must not be present in
the IANA-maintained module.
* An indication whether experimental values are included in the
IANA-maintained module. Absent such an indication, experimental
values MUST NOT be listed in the IANA-maintained module.
* An instruction about how to generate the "revision" statement.
A template for the IANA Considerations is provided in Section 5.3.1
for IANA-maintained modules with identities and Section 5.3.2 for
IANA- maintained modules with enumerations. Authors may modify the
template to reflect specifics of their modules (e.g., Multiple
registries can be listed for a single IANA-maintained module, no
explicit description (or name) field is listed under the
authoritative IANA registry).
The following templates are to be considered in addition to the
required information that is provided in Section 3.8.
Boucadair & Wu Expires 27 January 2024 [Page 58]
Internet-Draft Guidelines for YANG Documents July 2023
5.3.1. Template for IANA-Maintained Modules with Identities
This document defines the initial version of the IANA-maintained
"iana-foo" YANG module. The most recent version of the YANG module
is available from the "YANG Parameters" registry
[IANA-YANG-PARAMETERS].
IANA is requested to add this note to the registry:
New values must not be directly added to the "iana-foo" YANG
module. They must instead be added to the "foo" registry.
When a value is added to the "foo" registry, a new "identity"
statement must be added to the "iana-foo" YANG module. The name of
the "identity" is the lower-case of the name provided in the
registry. The "identity" statement should have the following sub-
statements defined:
"base": Contains 'name-base-identity-defined-in-foo'.
"status": Include only if a registration has been deprecated or
obsoleted. IANA "deprecated" maps to YANG status
"deprecated", and IANA "obsolete" maps to YANG status
"obsolete".
"description": Replicates the description from the registry.
"reference": Replicates the reference(s) from the registry with the
title of the document(s) added.
Unassigned or reserved values are not present in the module.
When the "iana-foo" YANG module is updated, a new "revision"
statement with a unique revision date must be added in front of the
existing revision statements.
IANA is requested to add this note to [reference-to-the-iana-foo-
registry]:
When this registry is modified, the YANG module "iana-foo"
[IANA_FOO_URL] must be updated as defined in RFCXXXX.
5.3.2. Template for IANA-Maintained Modules with Enumerations
Boucadair & Wu Expires 27 January 2024 [Page 59]
Internet-Draft Guidelines for YANG Documents July 2023
This document defines the initial version of the IANA-maintained
"iana-foo" YANG module. The most recent version of the YANG module
is available from the "YANG Parameters" registry
[IANA-YANG-PARAMETERS].
IANA is requested to add this note to the registry:
New values must not be directly added to the "iana-foo" YANG
module. They must instead be added to the "foo" registry.
When a value is added to the "foo" registry, a new "enum" statement
must be added to the "iana-foo" YANG module. The "enum" statement,
and sub-statements thereof, should be defined:
"enum": Replicates a name from the registry.
"value": Contains the decimal value of the IANA-assigned value.
"status": Is included only if a registration has been deprecated
or obsoleted. IANA "deprecated" maps to YANG status
"deprecated", and IANA "obsolete" maps to YANG status
"obsolete".
"description": Replicates the description from the registry.
"reference": Replicates the reference(s) from the registry with the
title of the document(s) added.
Unassigned or reserved values are not present in the module.
When the "iana-foo" YANG module is updated, a new "revision"
statement with a unique revision date must be added in front of the
existing revision statements.
IANA is requested to add this note to [reference-to-the-iana-foo-
registry]:
When this registry is modified, the YANG module "iana-foo"
[IANA_FOO_URL] must be updated as defined in RFCXXXX.
6. IANA Considerations
The following registration in the "ns" subregistry of the "IETF XML
Registry" [RFC3688] was detailed in [RFC6087]. This document
requests IANA to update this registration to reference this document.
Boucadair & Wu Expires 27 January 2024 [Page 60]
Internet-Draft Guidelines for YANG Documents July 2023
URI: urn:ietf:params:xml:ns:yang:ietf-template
Registrant Contact: The IESG.
XML: N/A, the requested URI is an XML namespace.
This document requests IANA to register the following YANG module in
the "YANG Module Names" registry [RFC6020] within the "YANG
Parameters" registry group.
+=====================+===========================================+
| Field | Value |
+=====================+===========================================+
| Name | ietf-template |
+---------------------+-------------------------------------------+
| Namespace | urn:ietf:params:xml:ns:yang:ietf-template |
+---------------------+-------------------------------------------+
| Prefix | temp |
+---------------------+-------------------------------------------+
| Maintained by IANA? | N |
+---------------------+-------------------------------------------+
| Reference | RFC XXXX |
+---------------------+-------------------------------------------+
Table 2: YANG Registry Assignment
Also, This document requests IANA to update the reference for the
"YANG Module Names" registry to point to the RFC number that will be
assigned to this document as it contains the template necessary for
registration in Appendix B.
7. Security Considerations
This document defines documentation guidelines for NETCONF or
RESTCONF content defined with the YANG data modeling language;
therefore, it does not introduce any new or increased security risks
into the management system.
8. References
8.1. Normative References
[ID-Guidelines]
IETF, "Guidelines to Authors of Internet-Drafts", n.d.,
.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
.
Boucadair & Wu Expires 27 January 2024 [Page 61]
Internet-Draft Guidelines for YANG Documents July 2023
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
.
[RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66,
RFC 3986, DOI 10.17487/RFC3986, January 2005,
.
[RFC5378] Bradner, S., Ed. and J. Contreras, Ed., "Rights
Contributors Provide to the IETF Trust", BCP 78, RFC 5378,
DOI 10.17487/RFC5378, November 2008,
.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, .
Boucadair & Wu Expires 27 January 2024 [Page 62]
Internet-Draft Guidelines for YANG Documents July 2023
[RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC8341, March 2018,
.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
.
[RFC8791] Bierman, A., Björklund, M., and K. Watsen, "YANG Data
Structure Extensions", RFC 8791, DOI 10.17487/RFC8791,
June 2020, .
[RFC8792] Watsen, K., Auerswald, E., Farrel, A., and Q. Wu,
"Handling Long Lines in Content of Internet-Drafts and
RFCs", RFC 8792, DOI 10.17487/RFC8792, June 2020,
.
[W3C.REC-xpath]
Clark, J. and S. DeRose, "XML Path Language (XPath)
Version 1.0", W3C Recommendation REC-xpath-19991116,
November 1999,
.
8.2. Informative References
[IANA-MOD-NAMES]
IANA, "YANG Module Names",
.
[IANA-XML] IANA, "IETF XML Registry",
.
[IANA-YANG-PARAMETERS]
"YANG Parameters", n.d.,
.
[IANA_BFD_URL]
IANA, "iana-bfd-types YANG Module",
.
Boucadair & Wu Expires 27 January 2024 [Page 63]
Internet-Draft Guidelines for YANG Documents July 2023
[IANA_BGP-L2_URL]
IANA, "iana-bgp-l2-encaps YANG Module",
.
[IANA_PW-Types_URL]
IANA, "iana-pseudowire-types YANG Module",
.
[RFC-STYLE]
RFC Editor, "Style Guide",
.
[RFC2026] Bradner, S., "The Internet Standards Process -- Revision
3", BCP 9, RFC 2026, DOI 10.17487/RFC2026, October 1996,
.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000,
.
[RFC3849] Huston, G., Lord, A., and P. Smith, "IPv6 Address Prefix
Reserved for Documentation", RFC 3849,
DOI 10.17487/RFC3849, July 2004,
.
[RFC4151] Kindberg, T. and S. Hawke, "The 'tag' URI Scheme",
RFC 4151, DOI 10.17487/RFC4151, October 2005,
.
[RFC4181] Heard, C., Ed., "Guidelines for Authors and Reviewers of
MIB Documents", BCP 111, RFC 4181, DOI 10.17487/RFC4181,
September 2005, .
[RFC5737] Arkko, J., Cotton, M., and L. Vegoda, "IPv4 Address Blocks
Reserved for Documentation", RFC 5737,
DOI 10.17487/RFC5737, January 2010,
.
[RFC6087] Bierman, A., "Guidelines for Authors and Reviewers of YANG
Data Model Documents", RFC 6087, DOI 10.17487/RFC6087,
January 2011, .
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC6991, July 2013,
.
Boucadair & Wu Expires 27 January 2024 [Page 64]
Internet-Draft Guidelines for YANG Documents July 2023
[RFC7223] Bjorklund, M., "A YANG Data Model for Interface
Management", RFC 7223, DOI 10.17487/RFC7223, May 2014,
.
[RFC7224] Bjorklund, M., "IANA Interface Type YANG Module",
RFC 7224, DOI 10.17487/RFC7224, May 2014,
.
[RFC7322] Flanagan, H. and S. Ginoza, "RFC Style Guide", RFC 7322,
DOI 10.17487/RFC7322, September 2014,
.
[RFC7841] Halpern, J., Ed., Daigle, L., Ed., and O. Kolkman, Ed.,
"RFC Streams, Headers, and Boilerplates", RFC 7841,
DOI 10.17487/RFC7841, May 2016,
.
[RFC7951] Lhotka, L., "JSON Encoding of Data Modeled with YANG",
RFC 7951, DOI 10.17487/RFC7951, August 2016,
.
[RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
.
[RFC8343] Bjorklund, M., "A YANG Data Model for Interface
Management", RFC 8343, DOI 10.17487/RFC8343, March 2018,
.
[RFC8349] Lhotka, L., Lindem, A., and Y. Qu, "A YANG Data Model for
Routing Management (NMDA Version)", RFC 8349,
DOI 10.17487/RFC8349, March 2018,
.
[RFC8407] Bierman, A., "Guidelines for Authors and Reviewers of
Documents Containing YANG Data Models", BCP 216, RFC 8407,
DOI 10.17487/RFC8407, October 2018,
.
[RFC8675] Boucadair, M., Farrer, I., and R. Asati, "A YANG Data
Model for Tunnel Interface Types", RFC 8675,
DOI 10.17487/RFC8675, November 2019,
.
[RFC8892] Thaler, D. and D. Romascanu, "Guidelines and Registration
Procedures for Interface Types and Tunnel Types",
RFC 8892, DOI 10.17487/RFC8892, August 2020,
.
Boucadair & Wu Expires 27 January 2024 [Page 65]
Internet-Draft Guidelines for YANG Documents July 2023
[RFC9108] Lhotka, L. and P. Špaček, "YANG Types for DNS Classes and
Resource Record Types", RFC 9108, DOI 10.17487/RFC9108,
September 2021, .
[RFC9132] Boucadair, M., Ed., Shallow, J., and T. Reddy.K,
"Distributed Denial-of-Service Open Threat Signaling
(DOTS) Signal Channel Specification", RFC 9132,
DOI 10.17487/RFC9132, September 2021,
.
[RFC9244] Boucadair, M., Ed., Reddy.K, T., Ed., Doron, E., Chen, M.,
and J. Shallow, "Distributed Denial-of-Service Open Threat
Signaling (DOTS) Telemetry", RFC 9244,
DOI 10.17487/RFC9244, June 2022,
.
[RFC9291] Boucadair, M., Ed., Gonzalez de Dios, O., Ed., Barguil,
S., and L. Munoz, "A YANG Network Data Model for Layer 2
VPNs", RFC 9291, DOI 10.17487/RFC9291, September 2022,
.
[Style] "IANA YANG", n.d., .
Appendix A. Module Review Checklist
This section is adapted from [RFC4181].
The purpose of a YANG module review is to review the YANG module for
both technical correctness and adherence to IETF documentation
requirements. The following checklist may be helpful when reviewing
an I-D:
* I-D Boilerplate -- verify that the document contains the required
I-D boilerplate (see ), including the appropriate statement to permit
publication as an RFC, and that the I-D boilerplate does not
contain references or section numbers.
* Abstract -- verify that the abstract does not contain references,
that it does not have a section number, and that its content
follows the guidelines in .
* Copyright Notice -- verify that the document has the appropriate
text regarding the rights that document contributors provide to
the IETF Trust [RFC5378]. Verify that it contains the full IETF
Trust copyright notice at the beginning of the document. The IETF
Trust Legal Provisions (TLP) can be found at:
Boucadair & Wu Expires 27 January 2024 [Page 66]
Internet-Draft Guidelines for YANG Documents July 2023
* Security Considerations section -- If none of the modules in the
document use YANG data structure, verify that the document uses
the latest approved template from the Operations and Management
(OPS) area website (see ) and that the guidelines therein have
been followed.
* IANA Considerations section -- this section must always be
present. For each module within the document, ensure that the
IANA Considerations section contains entries for the following
IANA registries:
XML Namespace Registry: Register the YANG module namespace.
YANG Module Registry: Register the YANG module name, prefix,
namespace, and RFC number, according to the rules specified in
[RFC6020].
* References -- verify that the references are properly divided
between normative and informative references, that RFCs 2119 and
8174 are included as normative references if the terminology
defined therein is used in the document, that all references
required by the boilerplate are present, that all YANG modules
containing imported items are cited as normative references, and
that all citations point to the most current RFCs, unless there is
a valid reason to do otherwise (for example, it is okay to include
an informative reference to a previous version of a specification
to help explain a feature included for backward compatibility).
Be sure citations for all imported modules are present somewhere
in the document text (outside the YANG module). If a YANG module
contains reference or "description" statements that refer to an
I-D, then the I-D is included as an informative reference.
* License -- verify that the document contains the Revised BSD
License in each YANG module or submodule. Some guidelines related
to this requirement are described in Section 3.1. Make sure that
the correct year is used in all copyright dates. Use the approved
text from the latest TLP document, which can be found at:
* Other Issues -- check for any issues mentioned in
that are not covered
elsewhere.
Boucadair & Wu Expires 27 January 2024 [Page 67]
Internet-Draft Guidelines for YANG Documents July 2023
* Technical Content -- review the actual technical content for
compliance with the guidelines in this document. The use of a
YANG module compiler is recommended when checking for syntax
errors. A list of freely available tools and other information,
including formatting advice, can be found at:
and
Checking for correct syntax, however, is only part of the job. It
is just as important to actually read the YANG module document
from the point of view of a potential implementor. It is
particularly important to check that "description" statements are
sufficiently clear and unambiguous to allow interoperable
implementations to be created.
Appendix B. YANG Module Template
file "ietf-template@2023-07-26.yang"
module ietf-template {
yang-version 1.1;
// replace this string with a unique namespace URN value
namespace "urn:ietf:params:xml:ns:yang:ietf-template";
// replace this string, and try to pick a unique prefix
prefix temp;
// import statements here: e.g.,
// import ietf-yang-types { prefix yang; }
// import ietf-inet-types { prefix inet; }
// identify the IETF working group if applicable
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
// update this contact statement with your info
contact
"WG Web:
WG List:
Editor: your-name
Boucadair & Wu Expires 27 January 2024 [Page 68]
Internet-Draft Guidelines for YANG Documents July 2023
";
// replace the first sentence in this description statement.
// replace the copyright notice with the most recent
// version, if it has been updated since the publication
// of this document
description
"This module defines a template for other YANG modules.
Copyright (c) IETF Trust and the persons
identified as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Revised BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove
// this note
// replace '2023-07-26' with the module publication date
// the format is (year-month-day)
revision 2023-07-26 {
description
"what changed in this revision";
reference "RFC XXXX: ";
}
// extension statements
// feature statements
// identity statements
// typedef statements
// grouping statements
// data definition statements
// augment statements
// rpc statements
// notification statements
// DO NOT put deviation statements in a published module
}
Boucadair & Wu Expires 27 January 2024 [Page 69]
Internet-Draft Guidelines for YANG Documents July 2023
Acknowledgments
Thanks to Jürgen Schönwälder, Ladislav Lhotka, and Qin Wu for the
discussion and valuable comments. Special thanks to Ladislav Lhotka
for sharing more context that led to the design documented in
[RFC9108].
Thanks to Andy Bierman, Italo Busi, Benoit Claise, Tom Petch, and
Randy Presuhn for the comments. Lou Berger suggested to include more
details about IANA considerations.
The author of RFC 8407: Andy Bierman
YumaWorks
email: andy@yumaworks.com
Acknowledgments from RFC 8407: The structure and contents of this
document are adapted from "Guidelines for Authors and Reviewers of
MIB Documents" [RFC4181], by C. M. Heard.
The working group thanks Martin Bjorklund, Juergen Schoenwaelder,
Ladislav Lhotka, Jernej Tuljak, Lou Berger, Robert Wilton, Kent
Watsen, and William Lupton for their extensive reviews and
contributions to this document.
Authors' Addresses
Mohamed Boucadair
Orange
France
Email: mohamed.boucadair@orange.com
Qin Wu
Huawei
China
Email: bill.wu@huawei.com
Boucadair & Wu Expires 27 January 2024 [Page 70]