| Internet-Draft | Registering SLAAC Addresses using DHCPv6 | August 2023 |
| Kumari, et al. | Expires 1 March 2024 | [Page] |
This document defines a method to inform a DHCPv6 server that a device has a self-generated or statically configured address.¶
This note is to be removed before publishing as an RFC.¶
The latest revision of this draft can be found at https://wkumari.github.io/draft-wkumari-dhc-addr-notification/draft-wkumari-dhc-addr-notification.html. Status information for this document may be found at https://datatracker.ietf.org/doc/draft-ietf-dhc-addr-notification/.¶
Discussion of this document takes place on the Dynamic Host Configuration Working Group mailing list (mailto:dhcwg@ietf.org), which is archived at https://mailarchive.ietf.org/arch/browse/dhcwg/. Subscribe at https://www.ietf.org/mailman/listinfo/dhcwg/.¶
Source for this draft and an issue tracker can be found at https://github.com/wkumari/draft-wkumari-dhc-addr-notification.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 1 March 2024.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
It is very common operational practice, especially in enterprise networks, to use IPv4 DHCP logs for troubleshooting or security purposes. Examples of this include a help desk dealing with a ticket such as "The CEO's laptop cannot connect to the printer"; if the MAC address of the printer is known (for example from an inventory system), the IPv4 address can be retrieved from the DHCP logs and the printer pinged to determine if it is reachable. Another common example is a Security Operations team discovering suspicious events in outbound firewall logs and then consulting DHCP logs to determine which employee's laptop had that IPv4 address at that time so that they can quarantine it and remove the malware.¶
This operational practice relies on the DHCP server knowing the IP address assignments. Therefore, the practice does not work if static IP addresses are manually configured on devices or self-assigned addresses (such as when self-configuring an IPv6 address using SLAAC [RFC4862]) are used.¶
The lack of this parity with IPv4 is one of the reasons which may be hindering IPv6 deployment, especially in enterprise networks.¶
This document provides a mechanism for a device to inform the DHCPv6 server that it has a self-configured IPv6 address (or has a statically configured address), and thus provides parity with IPv4 in this aspect.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The DHCPv6 protocol is used as the address registration protocol when a DHCPv6 server performs the role of an address registration server. The DHCPv6 IA Address option [RFC8415] is used to specify the address to be registered.¶
After successfully assigning a self-generated IPv6 address on one of its interfaces, a client implementing this specification SHOULD multicast an ADDR-REG-INFORM message in order to inform the DHCPv6 server that this self-generated address is in use (as shown in Fig.1).¶
+----+ +----------------+ +---------------+ |Host| |First-hop router| |Addr-Reg Server| +----+ +----------------+ +---------------+ | SLAAC | | |<--------->| | | | | | | ADDR-REG-INFORM | |------------------------------------------------->| | | |Register / log | | ADDR-REG-REPLY |address |<-------------------------------------------------
The DHCPv6 client sends an ADDR-REG-INFORM message to inform that an IPv6 address is in use. The format of the ADDR-REG-INFORM message is described as follows:¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type | transaction-id |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. options .
. (variable) .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
msg-type Identifies the DHCPv6 message type;
Set to ADDR-REG-INFORM (TBA1).
transaction-id The transaction ID for this message exchange.
options Options carried in this message.
The client MUST generate a transaction ID as described in [RFC8415] and insert this value in the "transaction-id" field.¶
The client MUST include a Client Identifier option in the ADDR-REG-INFORM message.¶
The ADDR-REG-INFORM message MUST NOT contain the Server Identifier option and MUST contain exactly one IA Address option containing the address being registered. The valid-lifetime and preferred-lifetime fields in the option MUST match the current Valid Lifetime and Preferred Lifetime of the address being registered.¶
The ADDR-REG-INFORM message is dedicated for clients to initiate an address registration request toward an address registration server. Consequently, clients MUST NOT put any Option Request Option(s) in the ADDR-REG-INFORM message. Clients MAY include other options, such as the Client FQDN Option [RFC4704].¶
The client sends the DHCPv6 ADDR-REG-INFORM message to the All_DHCP_Relay_Agents_and_Servers multicast address (ff02::1:2). The client MUST send separate messages for each address being registered.¶
Unlike other types of messages, which are sent from the link-local address of the client, the ADDR-REG-INFORM message MUST be sent from the address being registered. This is primarily for "fate sharing" purposes - for example, if the network implements some form of L2 security to prevent a client from spoofing other clients' addresses this prevents an attacker from spoofing ADDR-REG-INFORM messages.¶
On clients with multiple interfaces, the client MUST only send the packet on the network interface that has the address being registered, even if it has multiple interfaces with different addresses. If the same address is configured on multiple interfaces, then the client MUST send ADDR-REG-INFORM each time the address is configured on an interface that did not previously have it, and refresh each registration independently from the others.¶
The client MUST only send the ADDR-REG-INFORM message for valid ([RFC4862]) addresses of global scope ([RFC4007]). This includes ULA addresses, which are defined in [RFC4193] to have global scope. The client MUST NOT send the ADDR-REG-INFORM message for addresses configured by DHCPv6.¶
The client SHOULD NOT send the ADDR-REG-INFORM message if it has not received any Router Advertisement message with either M or O flags set to 1.¶
Clients MUST discard any received ADDR-REG-INFORM messages.¶
Servers MUST discard any ADDR-REG-INFORM messages that meet any of the following conditions:¶
If the message is not discarded, the address registration server SHOULD verify that the address being registered is "appropriate to the link" as defined by [RFC8415]. If the server believes that the address being registered is not appropriate to the link, it MUST drop the message, and SHOULD log this fact. Otherwise, the server:¶
Although a client "MUST NOT send the ADDR-REG-INFORM message for addresses configured by DHCPv6", if a server does receive such a message, it should log and discard it.¶
DHCPv6 relay agents and switches that relay address registration messages directly from clients SHOULD include the client's link-layer address in the relayed message using the Client Link-Layer Address option ([RFC6939]).¶
The server MUST acknowledge receipt of a valid ADDR-REG-INFORM message by sending back an ADDR-REG-REPLY message. The format of the ADDR-REG-REPLY message is described as follows:¶
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type | transaction-id |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. options .
. (variable) .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
msg-type Identifies the DHCPv6 message type;
Set to ADDR-REG-REPLY (TBA2).
transaction-id The transaction ID for this message exchange.
options Options carried in this message.
If the ADDR-REG-INFORM message that the server is replying to was not relayed, then the IPv6 destination address of the message MUST be the address being registered. If the ADDR-REG-INFORM message was relayed, then the server MUST construct the Relay-reply message as specified in [RFC8415] section 19.3.¶
The server MUST copy the transaction-id from the ADDR-REG-INFORM message to the transaction-id field of the ADDR-REG-REPLY.¶
The ADDR-REG-REPLY message MUST contain an IA Address option for the address being registered. The option MUST be identical to the one in the ADDR-REG-INFORM message that the server is replying to.¶
Servers MUST ignore any received ADDR-REG-REPLY messages.¶
Clients MUST discard any ADDR-REG-REPLY messages that meet any of the following conditions:¶
The ADDR-REG-REPLY message only indicates that the ADDR-REG-INFORM message has been received and that the client should not retansmit it. The ADDR-REG-REPLY message MUST NOT be considered as any indication of the address validity and MUST NOT be required for the address to be usable. DHCPv6 relays, or other devices that snoop ADDR-REG-REPLY messages, MUST NOT add or alter any forwarding or security state based on the ADDR-REG-REPLY message.¶
To reduce the effects of packet loss on registration, the client SHOULD retransmit the registration message. Retransmissions SHOULD follow the standard retransmission logic specified by section 15 of [RFC8415] with the following default parameters:¶
The client SHOULD allow these parameters to be configured by the administrator.¶
To comply with section 16.1 of [RFC8415], the client MUST leave the transaction ID unchanged in retransmissions of an ADDR-REG-INFORM message. When the client retranmits the registration message, the lifetimes in the packet MUST be updated so that they match the current lifetimes of the address.¶
If an ADDR-REG-REPLY message is received for the address being registered, the client MUST stop retransmission. However, the client cannot rely on the server acknowledging receipt of the registration message, because the server might not support address registration.¶
The client MUST refresh addresses as described below. Each refresh is scheduled after AddrRegRefresh seconds, where AddrRegRefresh is min(4 hours, 80% of the address's current Valid Lifetime). Refreshes SHOULD be jittered by +/- 10% to avoid synchronization causing a large number of registration messages to arrive at the same time.¶
Whenever the client creates an address or receives a PIO which changes the Valid Lifetime of an existing address by more than 1%, then:¶
Discussion: this algorithm ensures that refreshes are not sent too frequently, while ensuring that the server never believes that the address has expired when it has not. Specifically:¶
Registration refresh packets SHOULD be retransmitted using the same logic as described in the 'Retransmission' section above.¶
The client MUST generate a new transaction ID when refreshing the registration.¶
When the Client-Identifier-to-IPv6-address binding has expired, the server SHOULD remove it and consider the address as available for use.¶
The client MAY choose to notify the server when an address is no longer being used (e.g., if the client is disconnecting from the network, the address lifetime expired, or the address is being removed from the interface). To indicate that the address is not being used anymore the client MUST set the preferred-lifetime and valid-lifetime fields of the IA Address option to zero. If the server receives a message with a valid-lifetime of zero, it SHOULD act as if the address has expired.¶
DHCP clients SHOULD allow the administrator to disable sending ADDR-REG-INFORM messages. This could be used, for example, to reduce network traffic on networks where the servers are known not to support the message type. Sending the messages SHOULD be enabled by default.¶
An attacker may attempt to register a large number of addresses in quick succession in order to overwhelm the address registration server and / or fill up log files. Similar attack vectors exist today, e.g. an attacker can DoS the server with messages contained spoofed DUIDs.¶
If a network is using FCFS SAVI [RFC6620], then the DHCPv6 server can trust that the ADDR-REG-INFORM message was sent by the legitimate holder of the address. This prevents a host from registering an address owned by another host.¶
One of the use cases for the mechanism described in this document is to identify sources of malicious traffic after the fact. Note, however, that as the device itself is responsible for informing the DHCPv6 server that it is using an address, a malicious or compromised device can simply not send the ADDR-REG-INFORM message. This is an informational, optional mechanism, and is designed to aid in troubleshooting and forensics. On its own, it is not intended to be a strong security access mechanism. In particular, the ADDR-REG-INFORM message MUST not be used for authentication and authorization purposes, because in addition to the reasons above, the packets containing the message may be dropped.¶
This document defines two new DHCPv6 messages, ADDR-REG-INFORM message (TBA1) described in Section 4.1, and ADDR-REG-REPLY (TBA2) described in Section 4.2, that requires an allocation out of the registry of Message Types defined at http://www.iana.org/assignments/dhcpv6-parameters/.¶
Many thanks to Bernie Volz for significant review and feedback, as well as Hermin Anggawijaya, Brian Carpenter, Stuart Cheshire, Alan DeKok, Ryan Globus, Erik Kline, David Lamparter, Ted Lemon, Eric Levy-Abegnoli, Jim Reid, Michael Richardson, Mark Smith, Éric Vyncke, Timothy Winters for their feedback, comments and guidance. We apologize if we inadvertently forgot to acknowledge anyone’s contributions.¶
This document borrows heavily from a previous document, draft-ietf-dhc-addr-registration, which defined "a mechanism to register self-generated and statically configured addresses in DNS through a DHCPv6 server". That document was written Sheng Jiang, Gang Chen, Suresh Krishnan, and Rajiv Asati.¶