TEAS Working Group T. Saad Internet-Draft R. Gandhi Intended status: Standards Track Cisco Systems Inc Expires: 5 January 2024 X. Liu Alef Edge V. P. Beeram Juniper Networks I. Bryskin Individual O. Gonzalez de Dios Telefonica 4 July 2023 A YANG Data Model for Traffic Engineering Tunnels, Label Switched Paths and Interfaces draft-ietf-teas-yang-te-33 Abstract This document defines a YANG data model for the provisioning and management of Traffic Engineering (TE) tunnels, Label Switched Paths (LSPs), and interfaces. The model covers data that is independent of any technology or dataplane encapsulation and is divided into two YANG modules that cover device-specific, and device independent data. This model covers data for configuration, operational state, remote procedural calls, and event notifications. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 5 January 2024. Saad, et al. Expires 5 January 2024 [Page 1] Internet-Draft TE YANG Data Model July 2023 Copyright Notice Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terms and Conventions . . . . . . . . . . . . . . . . . . . . 3 2.1. Requirements Language . . . . . . . . . . . . . . . . . . 3 2.2. Terminology . . . . . . . . . . . . . . . . . . . . . . . 4 2.3. Prefixes in Data Node Names . . . . . . . . . . . . . . . 4 2.4. Model Tree Diagrams . . . . . . . . . . . . . . . . . . . 5 3. Design Considerations . . . . . . . . . . . . . . . . . . . . 5 3.1. State Data Organization . . . . . . . . . . . . . . . . . 6 4. Model Overview . . . . . . . . . . . . . . . . . . . . . . . 6 4.1. Module Relationship . . . . . . . . . . . . . . . . . . . 6 5. TE YANG Model . . . . . . . . . . . . . . . . . . . . . . . . 7 5.1. Module Structure . . . . . . . . . . . . . . . . . . . . 8 5.1.1. TE Globals . . . . . . . . . . . . . . . . . . . . . 9 5.1.2. TE Tunnels . . . . . . . . . . . . . . . . . . . . . 12 5.1.3. TE LSPs . . . . . . . . . . . . . . . . . . . . . . . 22 5.2. Tree Diagram . . . . . . . . . . . . . . . . . . . . . . 23 5.3. YANG Module . . . . . . . . . . . . . . . . . . . . . . . 25 6. TE Device YANG Model . . . . . . . . . . . . . . . . . . . . 57 6.1. Module Structure . . . . . . . . . . . . . . . . . . . . 58 6.1.1. TE Interfaces . . . . . . . . . . . . . . . . . . . . 58 6.2. Tree Diagram . . . . . . . . . . . . . . . . . . . . . . 59 6.3. YANG Module . . . . . . . . . . . . . . . . . . . . . . . 61 7. Notifications . . . . . . . . . . . . . . . . . . . . . . . . 74 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 74 9. Security Considerations . . . . . . . . . . . . . . . . . . . 75 10. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 76 11. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 76 12. Appendix A: Data Tree Examples . . . . . . . . . . . . . . . 77 12.1. Basic Tunnel Setup . . . . . . . . . . . . . . . . . . . 77 12.2. Global Named Path Constraints . . . . . . . . . . . . . 78 12.3. Tunnel with Global Path Constraint . . . . . . . . . . . 78 12.4. Tunnel with Per-tunnel Path Constraint . . . . . . . . . 79 Saad, et al. Expires 5 January 2024 [Page 2] Internet-Draft TE YANG Data Model July 2023 12.5. Tunnel State . . . . . . . . . . . . . . . . . . . . . . 80 12.6. Example TE Tunnel with Primary and Secondary Paths . . . 81 13. Appendix B: Full Model Tree Diagram . . . . . . . . . . . . . 89 14. References . . . . . . . . . . . . . . . . . . . . . . . . . 95 14.1. Normative References . . . . . . . . . . . . . . . . . . 95 14.2. Informative References . . . . . . . . . . . . . . . . . 98 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 99 1. Introduction YANG [RFC6020] and [RFC7950] is a data modeling language that was introduced to define the contents of a conceptual data store that allows networked devices to be managed using NETCONF [RFC6241]. YANG has proved relevant beyond its initial confines, as bindings to other interfaces (e.g. RESTCONF [RFC8040]) and encoding other than XML (e.g. JSON) are being defined. Furthermore, YANG data models can be used as the basis of implementation for other interfaces, such as CLI and programmatic APIs. This document describes a YANG data model for Traffic Engineering (TE) tunnels, Label Switched Paths (LSPs), and interfaces. The data model is divided into two YANG modules. The module 'ietf-te.yang' includes data that is generic and device-independent, while the module 'ietf-te-device.yang' includes data that is device-specific. The document describes a high-level relationship between the modules defined in this document, as well as other external protocol YANG modules. The TE generic YANG data model does not include any data specific to a signaling protocol. It is expected other data plane technology model(s) will augment the TE generic YANG data model. Also, it is expected other YANG modules that model TE signaling protocols, such as RSVP-TE ([RFC3209], [RFC3473]), or Segment-Routing TE (SR-TE) [RFC9256] will augment the generic TE YANG module. 2. Terms and Conventions 2.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. Saad, et al. Expires 5 January 2024 [Page 3] Internet-Draft TE YANG Data Model July 2023 2.2. Terminology The following terms are defined in [RFC6241] and are used in this specification: * client * configuration data * state data This document also makes use of the following terminology introduced in the YANG Data Modeling Language [RFC7950]: * augment * data model * data node 2.3. Prefixes in Data Node Names In this document, names of data nodes and other data model objects are prefixed using the standard prefix associated with the corresponding YANG imported modules, as shown in Table 1. +=================+======================+===============+ | Prefix | YANG module | Reference | +=================+======================+===============+ | yang | ietf-yang-types | [RFC6991] | +-----------------+----------------------+---------------+ | inet | ietf-inet-types | [RFC6991] | +-----------------+----------------------+---------------+ | rt-types | ietf-routing-types | [RFC8294] | +-----------------+----------------------+---------------+ | te-types | ietf-te-types | [RFC8776] | +-----------------+----------------------+---------------+ | te-packet-types | ietf-te-packet-types | [RFC8776] | +-----------------+----------------------+---------------+ | te | ietf-te | this document | +-----------------+----------------------+---------------+ | te-dev | ietf-te-device | this document | +-----------------+----------------------+---------------+ Table 1: Prefixes and corresponding YANG modules Saad, et al. Expires 5 January 2024 [Page 4] Internet-Draft TE YANG Data Model July 2023 2.4. Model Tree Diagrams The tree diagrams extracted from the module(s) defined in this document are given in subsequent sections as per the syntax defined in [RFC8340]. 3. Design Considerations This document describes a generic TE YANG data model that is independent of any dataplane technology. One of the design objectives is to allow specific data plane technology models to reuse the TE generic data model and possibly augment it with technology specific data. The elements of the generic TE YANG data model, including TE Tunnels, LSPs, and interfaces have leaf(s) that identify the technology layer where they reside. For example, the LSP encoding type can identify the technology associated with a TE Tunnel or LSP. Also, the generic TE YANG data model does not cover signaling protocol data. The signaling protocol used to instantiate TE LSPs are outside the scope of this document and expected to be covered by augmentations defined in other document(s). The following other design considerations are taken into account with respect to data organization: * The generic TE YANG data model 'ietf-te' contains device independent data and can be used to model data off a device (e.g. on a TE controller). When the model is used to manage a specific device, the model contains the TE Tunnels originating from the specific device. When the model is used to manage a TE controller, the 'tunnels' list contains all TE Tunnels and TE tunnel segments originating from device(s) that the TE controller manages. * The device-specific TE data is defined in module 'ietf-te-device' as shown in Figure 1. * In general, minimal elements in the model are designated as "mandatory" to allow freedom to vendors to adapt the data model to their specific product implementation. * Suitable defaults are specified for all configurable elements. * The model declares a number of TE functions as features that can be optionally supported. Saad, et al. Expires 5 January 2024 [Page 5] Internet-Draft TE YANG Data Model July 2023 3.1. State Data Organization The Network Management Datastore Architecture (NMDA) [RFC8342] addresses modeling state data for ephemeral objects. This document adopts the NMDA model for configuration and state data representation as per IETF guidelines for new IETF YANG models. 4. Model Overview The data models defined in this document cover the core TE features that are commonly supported by different vendor implementations. The support of extended or vendor specific TE feature(s) is expected to either be in augmentations, or deviations to this model that are defined in separate documents. 4.1. Module Relationship The generic TE YANG data model that is defined in "ietf-te.yang" covers the building blocks that are device independent and agnostic of any specific technology or control plane instances. The TE device model defined in "ietf-te-device.yang" augments the generic TE YANG data model and covers data that is specific to a device -- for example, attributes of TE interfaces, or TE timers that are local to a TE node. The TE data models for specific instances of data plane technology exist in separate YANG modules that augment the generic TE YANG data model. The TE data models for specific instances of signaling protocols are outside the scope of this document and are defined in other documents. For example, the RSVP-TE YANG model augmentation of the TE model is covered in a separate document. Saad, et al. Expires 5 January 2024 [Page 6] Internet-Draft TE YANG Data Model July 2023 TE generic +---------+ o: augment module | ietf-te |o-------------+ +---------+ \ o \ |\ \ | \ TE device module \ | +----------------+ \ | | ietf-te-device | \ | +----------------+ \ | o \ | / \ | / \ +---------------+ +---------------+ RSVP-TE module | ietf-rsvp-te^ |o . | ietf-te-mpls^ | +---------------+ \ +---------------+ | \ | \ | \ | \ | \ o +-------------------+ +------------+ | ietf-rsvp-otn-te^ | RSVP module | ietf-rsvp^ | +-------------------+ +------------+ RSVP-TE with OTN extensions X---oY indicates that module X augments module Y ^ indicates a module defined in other documents Figure 1: Relationship of TE module(s) with signaling protocol modules 5. TE YANG Model The generic TE YANG module ('ietf-te') is meant for the management and operation of a TE network. This includes creating, modifying and retrieving information about TE Tunnels, LSPs, and interfaces and their associated attributes (e.g. Administrative-Groups, SRLGs, etc.). A full tree diagram of the TE model is shown in the Appendix in Figure 13. Saad, et al. Expires 5 January 2024 [Page 7] Internet-Draft TE YANG Data Model July 2023 5.1. Module Structure The 'te' container is the top level container in the 'ietf-te' module. The presence of the 'te' container enables TE function system wide. Below provides further descriptions of containers that exist under the 'te' top level container. There are three further containers grouped under the 'te' container as shown in Figure 2 and described below. globals: The 'globals' container maintains the set of global TE attributes that can be applicable to TE Tunnels and interfaces. tunnels: The 'tunnels' container includes the list of TE Tunnels that are instantiated. Refer to Section 5.1.2 for further details on the properties of a TE Tunnel. lsps: The 'lsps' container includes the list of TE LSP(s) that are instantiated for TE Tunnels. Refer to Section 5.1.3 for further details on the properties of a TE LSP. The model also contains two Remote Procedure Calls (RPCs) as shown in Figure 13 and described below. tunnels-path-compute: A RPC to request path computation for a specific TE Tunnel. The RPC allows requesting path computation using atomic and stateless operation. A tunnel may also be configured in 'compute-only' mode to provide stateful path updates - see Section 5.1.2 for further details. tunnels-action: An RPC to request a specific action (e.g. reoptimize, or tear-and- setup) to be taken on a specific tunnel or all tunnels. Figure 13 shows the relationships of these containers and RPCs within the 'ietf-te' module. Saad, et al. Expires 5 January 2024 [Page 8] Internet-Draft TE YANG Data Model July 2023 module: ietf-te +--rw te! +--rw globals | ... +--rw tunnels | ... +--ro lsps ... rpcs: +---x tunnels-path-compute | +---w input | | ... | +--ro output | ... +---x tunnels-actions +---w input | ... +--ro output ... Figure 2: TE Tunnel model high-level YANG tree view 5.1.1. TE Globals The 'globals' container covers properties that control a TE feature's behavior system-wide, and its respective state as shown in Figure 3 and described in the text that follows. +--rw globals | +--rw named-admin-groups | | +--rw named-admin-group* [name] | | ... | +--rw named-srlgs | | +--rw named-srlg* [name] | | ... | +--rw named-path-constraints | +--rw named-path-constraint* [name] Figure 3: TE globals YANG subtree high-level structure named-admin-groups: A YANG container for the list of named (extended) administrative groups that may be applied to TE links. named-srlgs: Saad, et al. Expires 5 January 2024 [Page 9] Internet-Draft TE YANG Data Model July 2023 A YANG container for the list of named Shared Risk Link Groups (SRLGs) that may be applied to TE links. named-path-constraints: A YANG container for a list of named path constraints. Each named path constraint is composed of a set of constraints that can be applied during path computation. A named path constraint can be applied to multiple TE Tunnels. Path constraints may also be specified directly under the TE Tunnel. The path constraints specified under the TE Tunnel take precedence over the path constraints derived from the referenced named path constraint. A named path constraint entry can be formed of the path constraints shown in Figure 4: | +--rw named-path-constraints | +--rw named-path-constraint* [name] | {te-types:named-path-constraints}? | +--rw name string | +--rw te-bandwidth | | ... | +--rw link-protection? identityref | +--rw setup-priority? uint8 | +--rw hold-priority? uint8 | +--rw signaling-type? identityref | +--rw path-metric-bounds | | ... | +--rw path-affinities-values | | ... | +--rw path-affinity-names | | ... | +--rw path-srlgs-lists | | ... | +--rw path-srlgs-names | | ... | +--rw disjointness? | | te-path-disjointness | +--rw explicit-route-objects-always | | ... | +--rw path-in-segment! | | ... | +--rw path-out-segment! | ... Figure 4: Named path constraints YANG subtree o name: A YANG leaf that holds the named path constraint entry. This is unique in the list and used as a key. Saad, et al. Expires 5 January 2024 [Page 10] Internet-Draft TE YANG Data Model July 2023 o te-bandwidth: A YANG container that holds the technology agnostic TE bandwidth constraint. o link-protection: A YANG leaf that holds the link protection type constraint required for the links to be included in the computed path. o setup/hold priority: YANG leafs that hold the LSP setup and hold admission priority as defined in [RFC3209]. o signaling-type: A YANG leaf that holds the LSP setup type, such as RSVP-TE or SR. o path-metric-bounds: A YANG container that holds the set of metric bounds applicable on the computed TE tunnel path. o path-affinities-values: A YANG container that holds the set of affinity values and mask to be used during path computation. o path-affinity-names: A YANG container that holds the set of named affinity constraints and corresponding inclusion or exclusion instructions for each to be used during path computation. o path-srlgs-lists: A YANG container that holds the set of SRLG values and corresponding inclusion or exclusion instructions to be used during path computation. o path-srlgs-names: A YANG container that holds the set of named SRLG constraints and corresponding inclusion or exclusion instructions for each to be used during path computation. o disjointness: The level of resource disjointness constraint that the secondary path of a TE tunnel has to adhere to. o explicit-route-objects-always: A YANG container that contains two route objects lists: + 'route-object-exclude-always': a list of route entries to always exclude from the path computation. + 'route-object-include-exclude': a list of route entries to include or exclude in the path computation. Saad, et al. Expires 5 January 2024 [Page 11] Internet-Draft TE YANG Data Model July 2023 The 'route-object-include-exclude' is used to configure constraints on which route objects (e.g., nodes, links) are included or excluded in the path computation. The interpretation of an empty 'route-object-include- exclude' list depends on the TE Tunnel (end-to-end or Tunnel Segment) and on the specific path, according to the following rules: 1. An empty 'route-object-include-exclude' list for the primary path of an end-to-end TE Tunnel indicates that there are no route objects to be included or excluded in the path computation. 2. An empty 'route-object-include-exclude' list for the primary path of a TE Tunnel Segment indicates that no primary LSP is required for that TE Tunnel. 3. An empty 'route-object-include-exclude' list for a reverse path means it always follows the forward path (i.e., the TE Tunnel is co-routed). When the 'route- object-include-exclude' list is not empty, the reverse path is routed independently of the forward path. 4. An empty 'route-object-include-exclude' list for the secondary (forward) path indicates that the secondary path has the same endpoints as the primary path. o path-in-segment: A YANG container that contains a list of label restrictions that have to be taken into considerations when crossing domains. This TE tunnel segment in this case is being stitched to the upstream TE tunnel segment. o path-out-segment: A YANG container that contains a list of label restrictions that have to be taken into considerations when crossing domains. The TE tunnel segment in this case is being stitched to the downstream TE tunnel segment. 5.1.2. TE Tunnels The 'tunnels' container holds the list of TE Tunnels that are provisioned on ingress LER devices in the network as shown in Figure 5. Saad, et al. Expires 5 January 2024 [Page 12] Internet-Draft TE YANG Data Model July 2023 +--rw tunnels | +--rw tunnel* [name] | +--rw name string | +--rw alias? string | +--rw identifier? uint32 | +--rw color? uint32 | +--rw description? string | +--rw admin-state? identityref | +--ro operational-state? identityref | +--rw encoding? identityref | +--rw switching-type? identityref | +--rw source? te-types:te-node-id | +--rw destination? te-types:te-node-id | +--rw src-tunnel-tp-id? binary | +--rw dst-tunnel-tp-id? binary | +--rw bidirectional? boolean | +--rw controller | | +--rw protocol-origin? identityref | | +--rw controller-entity-id? string | +--rw reoptimize-timer? uint16 | +--rw association-objects | | +--rw association-object* [association-key] | | | ... | | +--rw association-object-extended* [association-key] | | ... | +--rw protection | | +--rw enable? boolean | | +--rw protection-type? identityref | | +--rw protection-reversion-disable? boolean | | +--rw hold-off-time? uint32 | | +--rw wait-to-revert? uint16 | | +--rw aps-signal-id? uint8 | +--rw restoration | | +--rw enable? boolean | | +--rw restoration-type? identityref | | +--rw restoration-scheme? identityref | | +--rw restoration-reversion-disable? boolean | | +--rw hold-off-time? uint32 | | +--rw wait-to-restore? uint16 | | +--rw wait-to-revert? uint16 | +--rw te-topology-identifier | | +--rw provider-id? te-global-id | | +--rw client-id? te-global-id | | +--rw topology-id? te-topology-id | +--rw te-bandwidth | | +--rw (technology)? | | ... | +--rw link-protection? identityref Saad, et al. Expires 5 January 2024 [Page 13] Internet-Draft TE YANG Data Model July 2023 | +--rw setup-priority? uint8 | +--rw hold-priority? uint8 | +--rw signaling-type? identityref | +--rw hierarchy | | +--rw dependency-tunnels | | | ... | | +--rw hierarchical-link | | ... | +--rw primary-paths | | +--rw primary-path* [name] | | ... | +--rw secondary-paths | | +--rw secondary-path* [name] | | ... | +--rw secondary-reverse-paths | | +--rw secondary-reverse-path* [name] | | ... | +---x tunnel-action | | +---w input | | | ... | | +--ro output | | ... | +---x protection-external-commands | +---w input | ... Figure 5: TE Tunnel list YANG subtree structure When the model is used to manage a specific device, the 'tunnels' list contains the TE Tunnels originating from the specific device. When the model is used to manage a TE controller, the 'tunnels' list contains all TE Tunnels and TE tunnel segments originating from device(s) that the TE controller manages. The TE Tunnel model allows the configuration and management of the following TE tunnel objects: TE Tunnel: A YANG container of one or more TE LSPs established between the source and destination TE Tunnel termination points. TE Path: An engineered path that once instantiated in the forwarding plane can be used to forward traffic from the source to the destination TE Tunnel termination points. Saad, et al. Expires 5 January 2024 [Page 14] Internet-Draft TE YANG Data Model July 2023 TE LSP: A TE LSP is a connection-oriented service established over a TE Path and that allows the delivery of traffic between the TE Tunnel source and destination termination points. TE Tunnel Segment: A part of a multi-domain TE Tunnel that is within a specific network domain. The TE Tunnel has a number of attributes that are set directly under the tunnel (as shown in Figure 5). The main attributes of a TE Tunnel are described below: operational-state: A YANG leaf that holds the operational state of the tunnel. name: A YANG leaf that holds the name of a TE Tunnel. The name of the TE Tunnel uniquely identifies the tunnel within the TE tunnel list. The name of the TE Tunnel can be formatted as a Uniform Resource Indicator (URI) by including the namespace to ensure uniqueness of the name amongst all the TE Tunnels present on devices and controllers. The configured TE Tunnels can be reported with the name of the device embedded within the TE Tunnel name. For initiated TE Tunnels from the controller, the controller is responsible to ensures that TE Tunnel names are unique. alias: A YANG leaf that holds an alternate name to the TE tunnel. Unlike the TE tunnel name, the alias can be modified at any time during the lifetime of the TE tunnel. identifier: A YANG leaf that holds an identifier of the tunnel. This identifier is unique amongst tunnels originated from the same ingress device. color: Saad, et al. Expires 5 January 2024 [Page 15] Internet-Draft TE YANG Data Model July 2023 A YANG leaf that holds the color associated with the TE tunnel. The color is used to map or steer services that carry matching color on to the TE tunnel as described in [RFC9012]. admin-state: A YANG leaf that holds the tunnel administrative state. The administrative status in state datastore transitions to 'tunnel- admin-up' when the tunnel used by the client layer, and to 'tunnel-admin-down' when it is not used by the client layer. operational-state: A YANG leaf that holds the tunnel operational state. encoding/switching: The 'encoding' and 'switching-type' are YANG leafs that define the specific technology in which the tunnel operates in as described in [RFC3945]. source/destination: YANG containers that hold the tunnel source and destination node endpoints identities, including: - te-node-id: A YANG leaf that holds the identifier of the source or destination of the TE Tunnel TE node identifiers as defined in [RFC8776]. - node-id: A YANG leaf that holds the identifier of the source or destination of the TE Tunnel node identifiers as defined in [RFC8345]. - tunnel-tp-id: A YANG leaf that holds the identifier of the source or destination of the TE Tunnel Termination Points (TTPs) as defined in [RFC8795]. The TTP identifiers are optional on nodes that have a single TTP per node. For example, TTP identifiers are optional for packet (IP/MPLS) routers. bidirectional: A YANG leaf that when present indicates the LSP of a TE Tunnel is bidirectional as defined in [rfc3473]. controller: Saad, et al. Expires 5 January 2024 [Page 16] Internet-Draft TE YANG Data Model July 2023 A YANG container that holds tunnel data relevant to an optional external TE controller that may initiate or control a tunnel. This target node may be augmented by external module(s), for example, to add data for PCEP initiated and/or delegated tunnels. reoptimize-timer: A YANG leaf to set the interval period for tunnel reoptimization. association-objects: A YANG container that holds the set of associations of the TE Tunnel to other TE Tunnels. Associations at the TE Tunnel level apply to all paths of the TE Tunnel. The TE tunnel associations can be overridden by associations configured directly under the TE Tunnel path. protection: A YANG container that holds the TE Tunnel protection properties. restoration: A YANG container that holds the TE Tunnel restoration properties. te-topology-identifier: A YANG container that holds the topology identifier associated with the topology where paths for the TE tunnel are computed as defined in [RFC8795]. network-id: A YANG leaf that can optionally be used to identify the network topology where paths for the TE tunnel are computed as defined in [RFC8345]. hierarchy: A YANG container that holds hierarchy related properties of the TE Tunnel. A TE LSP can be set up in MPLS or Generalized MPLS (GMPLS) networks to be used as a TE link to carry traffic in other (client) networks [RFC6107]. In this case, the model introduces the TE Tunnel hierarchical link endpoint parameters to identify the specific link in the client layer that the underlying TE Tunnel is associated with. The hierarchy container includes the following: Saad, et al. Expires 5 January 2024 [Page 17] Internet-Draft TE YANG Data Model July 2023 o dependency-tunnels: A set of hierarchical TE Tunnels provisioned or to be provisioned in the immediate lower layer that this TE tunnel depends on for multi-layer path computation. A dependency TE Tunnel is provisioned if and only if it is used (selected by path computation) at least by one client layer TE Tunnel. The TE link in the client layer network topology supported by a dependent TE Tunnel is dynamically created only when the dependency TE Tunnel is actually provisioned. o hierarchical-link: A YANG container that holds the identity of the hierarchical link (in the client layer) that is supported by this TE Tunnel. The endpoints of the hierarchical link are defined by TE tunnel source and destination node endpoints. The hierarchical link can be identified by its source and destination link termination point identifiers. primary-paths: A YANG container that holds the list of primary paths. A primary path is identified by 'name'. A primary path is selected from the list to instantiate a primary forwarding LSP for the tunnel. The list of primary paths is visited by order of preference. A primary path has the following attributes: - primary-reverse-path: A YANG container that holds properties of the primary reverse path. The reverse path is applicable to bidirectional TE Tunnels. - candidate-secondary-paths: A YANG container that holds a list of candidate secondary paths which may be used for the primary path to support path protection. The candidate secondary path(s) reference path(s) from the tunnel secondary paths list. The preference of the secondary paths is specified within the list and dictates the order of visiting the secondary path from the list. The attributes of a secondary path can be defined separately from the primary path. The attributes of a secondary path will be inherited from the associated 'active' primary when not explicitly defined for the secondary path. secondary-paths: A YANG container that holds the set of secondary paths. A secondary path is identified by 'name'. A secondary path can be referenced from the TE Tunnel's 'candidate-secondary-path' list. Saad, et al. Expires 5 January 2024 [Page 18] Internet-Draft TE YANG Data Model July 2023 secondary-reverse-paths: A YANG container that holds the set of secondary reverse paths. A secondary reverse path is identified by 'name'. A secondary reverse path can be referenced from the TE Tunnel's 'candidate- secondary-reverse-paths' list. A secondary reverse path contains attributes similar to a primary path. The following set of common path attributes are shared for primary (forward and reverse) and secondary paths: path-computation-method: A YANG leaf that specifies the method used for computing the TE path. path-computation-server: A YANG container that holds the path computation server properties when the path is externally queried. compute-only: A path of a TE Tunnel is, by default, provisioned so that it can be instantiated in the forwarding plane so that it can carry traffic as soon as a valid path is computed. In some cases, a TE path may be configured only for the purpose of computing a path and reporting it without the need to instantiate the LSP or commit any resources. In such a case, the path is configured in 'compute-only' mode to distinguish it from the default behavior. A 'compute-only' path is configured as a usual with the associated per path constraint(s) and properties on a device or TE controller. The device or TE controller computes the feasible path(s) subject to configured constraints. A client may query the 'compute-only' computed path properties 'on-demand', or alternatively, can subscribe to be notified of computed path(s) and whenever the path properties change. use-path-computation: A YANG leaf that indicates whether or not path computation is to be used for a specified path. lockdown: A YANG leaf that when set indicates the existing path should not be reoptimized after a failure on any of its traversed links. Saad, et al. Expires 5 January 2024 [Page 19] Internet-Draft TE YANG Data Model July 2023 path-scope: A YANG leaf that specifies the path scope if segment or an end-to- end path. preference: A YANG leaf that specifies the preference for the path. The lower the number higher the preference. k-requested-paths: A YANG leaf that specifies the number of k-shortest-paths requested from the path computation server and returned sorted by its optimization objective. association-objects: A YANG container that holds a list of tunnel association properties. optimizations: A YANG container that holds the optimization objectives that path computation will use to select a path. named-path-constraint: A YANG leafref that references an entry from the global list of named path constraints. te-bandwidth: A YANG container that holds the path bandwidth (see [RFC8776]). link-protection: A YANG leaf that specifies the link protection type required for the links to be included the computed path (see [RFC8776]). setup/hold-priority: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. signaling-type: Saad, et al. Expires 5 January 2024 [Page 20] Internet-Draft TE YANG Data Model July 2023 see description provided in Section 5.1.1. This value overrides the provided one in the referenced named-path-constraint. path-metric-bounds: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. path-affinities-values: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. path-affinity-names: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. path-srlgs-lists: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. path-srlgs-names: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. disjointness: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. explicit-route-objects-always: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. path-in-segment: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. path-out-segment: see description provided in Section 5.1.1. These values override those provided in the referenced named-path-constraint. Saad, et al. Expires 5 January 2024 [Page 21] Internet-Draft TE YANG Data Model July 2023 computed-paths-properties: A YANG container that holds properties for the list of computed paths. computed-path-error-infos: A YANG container that holds a list of errors related to the path. lsp-provisioning-error-infos: A YANG container that holds the list of LSP provisioning error information. lsps: A YANG container that holds a list of LSPs that have been instantiated for this specific path. In addition to the path common attributes, the primary path has the following attributes that are not present in the secondary path: * Only the primary path contains the list of 'candidate-secondary- paths' that can protect the primary path. * Only the primary path can contain a primary-reverse-path associated with the primary path (and its associated list of 'candidate-secondary-reverse-path'). 5.1.3. TE LSPs The 'lsps' container includes the set of TE LSP(s) that have been instantiated. A TE LSP is identified by a 3-tuple ('tunnel-name', 'lsp-id', 'node'). When the model is used to manage a specific device, the 'lsps' list contains all TE LSP(s) that traverse the device (including ingressing, transiting and egressing the device). When the model is used to manage a TE controller, the 'lsps' list contains the TE LSP(s) on devices managed by the controller that act as ingress, and may optionally include TE LSPs on devices managed by the controller that act as transit or egress role. Saad, et al. Expires 5 January 2024 [Page 22] Internet-Draft TE YANG Data Model July 2023 5.2. Tree Diagram Figure 6 shows the tree diagram of depth=4 for the generic TE YANG model defined in modules 'ietf-te.yang'. The full tree diagram is shown in Section 13. module: ietf-te +--rw te +--rw enable? boolean +--rw globals | +--rw named-admin-groups | | +--rw named-admin-group* [name] | | {te-types:extended-admin-groups, | | te-types:named-extended-admin-groups}? | | ... | +--rw named-srlgs | | +--rw named-srlg* [name] {te-types:named-srlg-groups}? | | ... | +--rw named-path-constraints | +--rw named-path-constraint* [name] | {te-types:named-path-constraints}? | ... +--rw tunnels | +--rw tunnel* [name] | +--rw name string | +--rw alias? string | +--rw identifier? uint32 | +--rw color? uint32 | +--rw description? string | +--rw admin-state? identityref | +--ro operational-state? identityref | +--rw encoding? identityref | +--rw switching-type? identityref | +--rw source | | ... | +--rw destination | | ... | +--rw bidirectional? boolean | +--rw controller | | ... | +--rw reoptimize-timer? uint16 | +--rw association-objects | | ... | +--rw protection | | ... | +--rw restoration | | ... | +--rw network-id? nw:network-id Saad, et al. Expires 5 January 2024 [Page 23] Internet-Draft TE YANG Data Model July 2023 | +--rw te-topology-identifier | | ... | +--rw te-bandwidth | | ... | +--rw link-protection? identityref | +--rw setup-priority? uint8 | +--rw hold-priority? uint8 | +--rw signaling-type? identityref | +--rw hierarchy | | ... | +--rw primary-paths | | ... | +--rw secondary-paths | | ... | +--rw secondary-reverse-paths | | ... | +---x tunnel-action | | ... | +---x protection-external-commands | ... +--ro lsps +--ro lsp* [tunnel-name lsp-id node] +--ro tunnel-name string +--ro lsp-id uint16 +--ro node | te-types:te-node-id +--ro source? | te-types:te-node-id +--ro destination? | te-types:te-node-id +--ro tunnel-id? uint16 +--ro extended-tunnel-id? | yang:dotted-quad +--ro operational-state? identityref +--ro signaling-type? identityref +--ro origin-type? enumeration +--ro lsp-resource-status? enumeration +--ro lockout-of-normal? boolean +--ro freeze? boolean +--ro lsp-protection-role? enumeration +--ro lsp-protection-state? identityref +--ro protection-group-ingress-node-id? | te-types:te-node-id +--ro protection-group-egress-node-id? | te-types:te-node-id +--ro lsp-actual-route-information ... Saad, et al. Expires 5 January 2024 [Page 24] Internet-Draft TE YANG Data Model July 2023 rpcs: +---x tunnels-path-compute | +---w input | | +---w path-compute-info | +--ro output | +--ro path-compute-result +---x tunnels-actions +---w input | +---w tunnel-info | | +---w (filter-type) | | ... | +---w action-info | +---w action? identityref | +---w disruptive? empty +--ro output +--ro action-result? identityref Figure 6: Tree diagram of depth-4 of TE Tunnel YANG data model 5.3. YANG Module The generic TE YANG module 'ietf-te' imports the following modules: * ietf-te-types defined in [RFC8776] * ietf-yang-types and ietf-inet-types defined in [RFC6991] * ietf-network and ietf-network-topology defined in [RFC8345] This module references the following documents: [RFC4206], [RFC4427], [RFC4872], [RFC3209], [RFC6780], [RFC7471], [RFC9012], [RFC8570], [RFC8232], [RFC7271], [RFC8234], [RFC7308], and [ITU_G.808.1]. file "ietf-te@2023-06-16.yang" module ietf-te { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-te"; /* Replace with IANA when assigned */ prefix te; /* Import TE generic types */ import ietf-te-types { prefix te-types; reference "RFC8776: Common YANG Data Types for Traffic Engineering."; Saad, et al. Expires 5 January 2024 [Page 25] Internet-Draft TE YANG Data Model July 2023 } import ietf-inet-types { prefix inet; reference "RFC6991: Common YANG Data Types."; } import ietf-yang-types { prefix yang; reference "RFC6991: Common YANG Data Types."; } import ietf-network { prefix "nw"; reference "RFC 8345: A YANG Data Model for Network Topologies"; } import ietf-network-topology { prefix "nt"; reference "RFC 8345: A YANG Data Model for Network Topologies"; } organization "IETF Traffic Engineering Architecture and Signaling (TEAS) Working Group."; contact "WG Web: WG List: Editor: Tarek Saad Editor: Rakesh Gandhi Editor: Vishnu Pavan Beeram Editor: Himanshu Shah Editor: Xufeng Liu Editor: Igor Bryskin Editor: Oscar Gonzalez de Dios Saad, et al. Expires 5 January 2024 [Page 26] Internet-Draft TE YANG Data Model July 2023 "; description "YANG data module for TE configuration, state, and RPCs. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2023 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX (https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself for full legal notices."; // RFC Ed.: replace XXXX with actual RFC number and remove this // note. // RFC Ed.: update the date below with the date of RFC publication // and remove this note. revision 2023-06-16 { description "Initial revision for the TE generic YANG module."; reference "RFCXXXX: A YANG Data Model for Traffic Engineering Tunnels and Interfaces."; } typedef tunnel-ref { type leafref { path "/te:te/te:tunnels/te:tunnel/te:name"; } description "This type is used by data models that need to reference configured TE tunnel."; } typedef te-gen-node-id { type union { type te-types:te-node-id; type inet:ip-address; type nw:node-id; Saad, et al. Expires 5 January 2024 [Page 27] Internet-Draft TE YANG Data Model July 2023 } description "Generic type that identifies a node in a TE topology."; } /** * TE tunnel generic groupings */ grouping te-generic-node-id { description "A reusable grouping for a TE generic node identifier."; leaf id { type te-gen-node-id; description "The identifier of the node. Can be represented as IP address or dotted quad address or as an URI."; } leaf type { type enumeration { enum ip { description "IP address representation of the node identifier."; } enum dotted-quad { description "Dotted quad address representation of the node identifier."; } enum node-id { description "URI representation of the node identifier."; } } description "Type of node identifier representation."; } } grouping path-common-properties { description "Common path attributes."; leaf name { type string; description "TE path name."; } leaf path-computation-method { Saad, et al. Expires 5 January 2024 [Page 28] Internet-Draft TE YANG Data Model July 2023 type identityref { base te-types:path-computation-method; } default "te-types:path-locally-computed"; description "The method used for computing the path, either locally computed, queried from a server or not computed at all (explicitly configured)."; } container path-computation-server { when "derived-from-or-self(../path-computation-method, " + "'te-types:path-externally-queried')" { description "The path-computation server when the path is externally queried."; } uses te-generic-node-id; description "Address of the external path computation server."; } leaf compute-only { type empty; description "When present, the path is computed and updated whenever the topology is updated. No resources are committed or reserved in the network."; } leaf use-path-computation { when "derived-from-or-self(../path-computation-method, " + "'te-types:path-locally-computed')"; type boolean; default "true"; description "When 'true' indicates the path is dynamically computed and/or validated against the Traffic-Engineering Database (TED), and when 'false' indicates no path expansion or validation against the TED is required."; } leaf lockdown { type empty; description "When present, indicates no reoptimization to be attempted for this path."; } leaf path-scope { type identityref { base te-types:path-scope-type; Saad, et al. Expires 5 January 2024 [Page 29] Internet-Draft TE YANG Data Model July 2023 } default "te-types:path-scope-end-to-end"; config false; description "Indicates whether the path is a segment or portion of of the full path., or is the an end-to-end path for the TE Tunnel."; } } /* This grouping is re-used in path-computation rpc */ grouping path-compute-info { description "Attributes used for path computation request."; uses tunnel-associations-properties; uses te-types:generic-path-optimization; leaf named-path-constraint { if-feature "te-types:named-path-constraints"; type leafref { path "/te:te/te:globals/te:named-path-constraints/" + "te:named-path-constraint/te:name"; } description "Reference to a globally defined named path constraint set."; } uses path-constraints-common; } /* This grouping is re-used in path-computation rpc */ grouping path-forward-properties { description "The path preference."; leaf preference { type uint8 { range "1..255"; } default "1"; description "Specifies a preference for this path. The lower the number higher the preference."; } leaf co-routed { when "/te:te/te:tunnels/te:tunnel/te:bidirectional = 'true'" { description "Applicable to bidirectional tunnels only."; } type boolean; default "false"; Saad, et al. Expires 5 January 2024 [Page 30] Internet-Draft TE YANG Data Model July 2023 description "Indicates whether the reverse path must to be co-routed with the primary."; } } /* This grouping is re-used in path-computation rpc */ grouping k-requested-paths { description "The k-shortest paths requests."; leaf k-requested-paths { type uint8; default "1"; description "The number of k-shortest-paths requested from the path computation server and returned sorted by its optimization objective."; } } grouping path-state { description "TE per path state parameters."; uses path-computation-response; container lsp-provisioning-error-infos { config false; description "LSP provisioning error information."; list lsp-provisioning-error-info { description "List of LSP provisioning error info entries."; leaf error-reason { type identityref { base te-types:lsp-provisioning-error-reason; } description "LSP provision error type."; } leaf error-description { type string; description "The textual representation of the error occurred during path computation."; } leaf error-timestamp { type yang:date-and-time; description "Timestamp of when the reported error occurred."; Saad, et al. Expires 5 January 2024 [Page 31] Internet-Draft TE YANG Data Model July 2023 } leaf error-node-id { type te-types:te-node-id; description "Node identifier of node where error occurred."; } leaf error-link-id { type te-types:te-tp-id; description "Link ID where the error occurred."; } leaf lsp-id { type uint16; description "The LSP-ID for which path computation was performed."; } } } container lsps { config false; description "The TE LSPs container."; list lsp { key "node lsp-id"; description "List of LSPs associated with the tunnel."; leaf tunnel-name { type leafref { path "/te:te/te:lsps/te:lsp/te:tunnel-name"; } description "TE tunnel name."; } leaf node { type leafref { path "/te:te/te:lsps/te:lsp[tunnel-name=" + "current()/../te:tunnel-name][lsp-id=" + "current()/../te:lsp-id]/te:node"; } description "The node where the LSP state resides on."; } leaf lsp-id { type leafref { path "/te:te/te:lsps/te:lsp[tunnel-name=" + "current()/../tunnel-name]/te:lsp-id"; } description "The TE LSP identifier."; } } Saad, et al. Expires 5 January 2024 [Page 32] Internet-Draft TE YANG Data Model July 2023 } } /* This grouping is re-used in path-computation rpc */ grouping path-computation-response { description "Attributes reported by path computation response."; container computed-paths-properties { config false; description "Computed path properties container."; list computed-path-properties { key "k-index"; description "List of computed paths."; leaf k-index { type uint8; description "The k-th path returned from the computation server. A lower k value path is more optimal than higher k value path(s)"; } uses te-types:generic-path-properties { augment "path-properties" { description "additional path properties returned by path computation."; uses te-types:te-bandwidth; leaf disjointness-type { type te-types:te-path-disjointness; config false; description "The type of resource disjointness. When reported for a primary path, it represents the minimum level of disjointness of all the secondary paths. When reported for a secondary path, it represents the disjointness of the secondary path."; } } } } } container computed-path-error-infos { config false; description "Path computation information container."; list computed-path-error-info { description Saad, et al. Expires 5 January 2024 [Page 33] Internet-Draft TE YANG Data Model July 2023 "List of path computation info entries."; leaf error-description { type string; description "Textual representation of the error that occurred during path computation."; } leaf error-timestamp { type yang:date-and-time; description "Timestamp of last path computation attempt."; } leaf error-reason { type identityref { base te-types:path-computation-error-reason; } description "Reason for the path computation error."; } } } } grouping protection-restoration-properties { description "Protection and restoration parameters."; container protection { description "Protection parameters."; leaf protection-type { type identityref { base te-types:lsp-protection-type; } default "te-types:lsp-protection-unprotected"; description "LSP protection type."; } leaf protection-reversion-disable { type boolean; default "false"; description "Disable protection reversion to working path."; } leaf hold-off-time { type uint32; units "milli-seconds"; description "The time between the declaration of an SF or SD condition Saad, et al. Expires 5 January 2024 [Page 34] Internet-Draft TE YANG Data Model July 2023 and the initialization of the protection switching algorithm."; reference "RFC4427"; } leaf wait-to-revert { type uint16; units "seconds"; description "Time to wait before attempting LSP reversion."; reference "RFC4427"; } leaf aps-signal-id { type uint8 { range "1..255"; } default "1"; description "The APS signal number used to reference the traffic of this tunnel. The default value for normal traffic is 1. The default value for extra-traffic is 255. If not specified, non-default values can be assigned by the server, if and only if, the server controls both endpoints."; reference "ITU_G.808.1"; } } container restoration { description "Restoration parameters."; leaf restoration-type { type identityref { base te-types:lsp-restoration-type; } default "te-types:lsp-restoration-restore-none"; description "LSP restoration type."; } leaf restoration-scheme { type identityref { base te-types:restoration-scheme-type; } default "te-types:restoration-scheme-preconfigured"; description "LSP restoration scheme."; } Saad, et al. Expires 5 January 2024 [Page 35] Internet-Draft TE YANG Data Model July 2023 leaf restoration-reversion-disable { type boolean; default "false"; description "Disable restoration reversion to working path."; } leaf hold-off-time { type uint32; units "milli-seconds"; description "The time between the declaration of an SF or SD condition and the initialization of the protection switching algorithm."; reference "RFC4427"; } leaf wait-to-restore { type uint16; units "seconds"; description "Time to wait before attempting LSP restoration."; reference "RFC4427"; } leaf wait-to-revert { type uint16; units "seconds"; description "Time to wait before attempting LSP reversion."; reference "RFC4427"; } } } grouping tunnel-associations-properties { description "TE tunnel association grouping."; container association-objects { description "TE tunnel associations."; list association-object { key "association-key"; unique "type id source/id source/type"; description "List of association base objects."; reference "RFC4872"; Saad, et al. Expires 5 January 2024 [Page 36] Internet-Draft TE YANG Data Model July 2023 leaf association-key { type string; description "Association key used to identify a specific association in the list"; } leaf type { type identityref { base te-types:association-type; } description "Association type."; reference "RFC4872"; } leaf id { type uint16; description "Association identifier."; reference "RFC4872"; } container source { uses te-generic-node-id; description "Association source."; reference "RFC4872"; } } list association-object-extended { key "association-key"; unique "type id source/id source/type global-source extended-id"; description "List of extended association objects."; reference "RFC6780"; leaf association-key { type string; description "Association key used to identify a specific association in the list"; } leaf type { type identityref { base te-types:association-type; } Saad, et al. Expires 5 January 2024 [Page 37] Internet-Draft TE YANG Data Model July 2023 description "Association type."; reference "RFC4872, RFC6780"; } leaf id { type uint16; description "Association identifier."; reference "RFC4872, RFC6780"; } container source { uses te-generic-node-id; description "Association source."; reference "RFC4872, RFC6780"; } leaf global-source { type uint32; description "Association global source."; reference "RFC6780"; } leaf extended-id { type yang:hex-string; description "Association extended identifier."; reference "RFC6780"; } } } } grouping tunnel-end-point { description "Common grouping used to specify the tunnel source and destination end-points."; leaf node-id { type nw:node-id; description "The TE tunnel end-point node identifier"; } leaf te-node-id { type te-types:te-node-id; Saad, et al. Expires 5 January 2024 [Page 38] Internet-Draft TE YANG Data Model July 2023 description "The TE tunnel end-point TE node identifier"; } leaf tunnel-tp-id { when "../node-id or ../te-node-id" { description "The TE tunnel termination point identifier is local to a node"; } type binary; description "The TE tunnel end-point TE tunnel termination point identifier"; } } /* This grouping is re-used in path-computation rpc */ grouping tunnel-common-attributes { description "Common grouping to define the TE tunnel parameters"; container source { description "TE tunnel source end-point."; uses tunnel-end-point; } container destination { description "TE tunnel destination end-point."; uses tunnel-end-point; } leaf bidirectional { type boolean; default "false"; description "Indicates a bidirectional tunnel"; } } /* This grouping is re-used in path-computation rpc */ grouping tunnel-hierarchy-properties { description "A grouping for TE tunnel hierarchy information."; container hierarchy { description "Container for TE hierarchy related information."; container dependency-tunnels { description "List of tunnels that this tunnel can be potentially Saad, et al. Expires 5 January 2024 [Page 39] Internet-Draft TE YANG Data Model July 2023 dependent on."; list dependency-tunnel { key "name"; description "A tunnel entry that this tunnel can potentially depend on."; leaf name { type leafref { path "/te:te/te:tunnels/te:tunnel/te:name"; require-instance false; } description "Dependency tunnel name. The tunnel may not have been instantiated yet."; } uses te-types:encoding-and-switching-type; } } container hierarchical-link { description "Identifies a hierarchical link (in client layer) that this tunnel is associated with. By default, the topology of the hierarchical link is the same topology of the tunnel;"; reference "RFC4206"; leaf enable { type boolean; default "false"; description "Enables the hierarchical link properties supported by this tunnel"; } leaf local-node-id { type nw:node-id; description "The local node identifier."; } leaf local-te-node-id { type te-types:te-node-id; description "The local TE node identifier."; } leaf local-link-tp-id { type nt:tp-id; description "The local link termination point identifier."; } Saad, et al. Expires 5 January 2024 [Page 40] Internet-Draft TE YANG Data Model July 2023 leaf local-te-link-tp-id { type te-types:te-tp-id; description "The local TE link termination point identifier."; } leaf remote-link-tp-id { type nt:tp-id; description "The remote link termination point identifier."; } leaf remote-te-node-id { type te-types:te-node-id; description "Remote TE node identifier."; } leaf network-id { type nw:network-id; description "The network topology identifier where the hierarchical link supported by this TE tunnel is instantiated."; } uses te-types:te-topology-identifier { description "The TE topology identifier where the hierarchical link supported by this TE tunnel is instantiated."; } } } } grouping path-constraints-common { description "Global named path constraints configuration grouping."; uses te-types:common-path-constraints-attributes { description "The constraints applicable to the path. This includes: - The path bandwidth constraint - The path link protection type constraint - The path setup/hold priority constraint - path signaling type constraint - path metric bounds constraint. The unit of path metric bound is interpreted in the context of the metric-type. For example for metric-type 'path-metric-loss', the bound is multiples of the basic unit 0.000003% as described in RFC7471 for OSPF, and RFC8570 for ISIS. - path affinity constraints - path SRLG constraints"; Saad, et al. Expires 5 January 2024 [Page 41] Internet-Draft TE YANG Data Model July 2023 } uses te-types:generic-path-disjointness; uses te-types:path-constraints-route-objects; container path-in-segment { presence "The end-to-end tunnel starts in a previous domain; this tunnel is a segment in the current domain."; description "If an end-to-end tunnel crosses multiple domains using the same technology, some additional constraints have to be taken in consideration in each domain. This TE tunnel segment is stitched to the upstream TE tunnel segment."; uses te-types:label-set-info; } container path-out-segment { presence "The end-to-end tunnel is not terminated in this domain; this tunnel is a segment in the current domain."; description "If an end-to-end tunnel crosses multiple domains using the same technology, some additional constraints have to be taken in consideration in each domain. This TE tunnel segment is stitched to the downstream TE tunnel segment."; uses te-types:label-set-info; } } /** * TE container */ container te { description "TE global container."; leaf enable { type boolean; description "Enables the TE component features."; } /* TE Global Data */ container globals { description "Globals TE system-wide configuration data container."; container named-admin-groups { description "TE named admin groups container."; Saad, et al. Expires 5 January 2024 [Page 42] Internet-Draft TE YANG Data Model July 2023 list named-admin-group { if-feature "te-types:extended-admin-groups"; if-feature "te-types:named-extended-admin-groups"; key "name"; description "List of named TE admin-groups."; leaf name { type string; description "A string name that uniquely identifies a TE interface named admin-group."; } leaf bit-position { type uint32; description "Bit position representing the administrative group."; reference "RFC3209 and RFC7308"; } } } container named-srlgs { description "TE named SRLGs container."; list named-srlg { if-feature "te-types:named-srlg-groups"; key "name"; description "A list of named SRLG groups."; leaf name { type string; description "A string name that uniquely identifies a TE interface named SRLG."; } leaf value { type te-types:srlg; description "An SRLG value."; } leaf cost { type uint32; description "SRLG associated cost. Used during path to append the path cost when traversing a link with this SRLG."; } Saad, et al. Expires 5 January 2024 [Page 43] Internet-Draft TE YANG Data Model July 2023 } } container named-path-constraints { description "TE named path constraints container."; list named-path-constraint { if-feature "te-types:named-path-constraints"; key "name"; leaf name { type string; description "A string name that uniquely identifies a path constraint set."; } uses path-constraints-common; description "A list of named path constraints."; } } } /* TE Tunnel Data */ container tunnels { description "Tunnels TE configuration data container."; list tunnel { key "name"; description "The list of TE tunnels."; leaf name { type string; description "TE tunnel name."; } leaf alias { type string; description "An alternate name of the TE tunnel that can be modified anytime during its lifetime."; } leaf identifier { type uint32; description "TE tunnel Identifier."; reference "RFC3209"; } leaf color { Saad, et al. Expires 5 January 2024 [Page 44] Internet-Draft TE YANG Data Model July 2023 type uint32; description "The color associated with the TE tunnel."; reference "RFC9012"; } leaf description { type string; default "None"; description "Textual description for this TE tunnel."; } leaf admin-state { type identityref { base te-types:tunnel-admin-state-type; } default "te-types:tunnel-admin-state-up"; description "TE tunnel administrative state."; } leaf operational-state { type identityref { base te-types:tunnel-state-type; } config false; description "TE tunnel operational state."; } uses te-types:encoding-and-switching-type; uses tunnel-common-attributes; container controller { description "Contains tunnel data relevant to external controller(s). This target node may be augmented by external module(s), for example, to add data for PCEP initiated and/or delegated tunnels."; leaf protocol-origin { type identityref { base te-types:protocol-origin-type; } description "The protocol origin for instantiating the tunnel."; } leaf controller-entity-id { type string; description "An identifier unique within the scope of visibility that associated with the entity that controls the tunnel."; reference "RFC8232"; Saad, et al. Expires 5 January 2024 [Page 45] Internet-Draft TE YANG Data Model July 2023 } } leaf reoptimize-timer { type uint16; units "seconds"; description "Frequency of reoptimization of a traffic engineered LSP."; } uses tunnel-associations-properties; uses protection-restoration-properties; uses te-types:tunnel-constraints; uses tunnel-hierarchy-properties; container primary-paths { description "The set of primary paths."; reference "RFC4872"; list primary-path { key "name"; description "List of primary paths for this tunnel."; leaf active { type boolean; config false; description "Indicates an active path that has been selected from the primary paths list."; } uses path-common-properties; uses path-forward-properties; uses k-requested-paths; uses path-compute-info; uses path-state; container primary-reverse-path { when "../../../te:bidirectional = 'true'"; description "The reverse primary path properties."; uses path-common-properties; uses path-compute-info; uses path-state; container candidate-secondary-reverse-paths { description "The set of referenced candidate reverse secondary paths from the full set of secondary reverse paths which may be used for this primary path."; list candidate-secondary-reverse-path { key "secondary-reverse-path"; ordered-by user; Saad, et al. Expires 5 January 2024 [Page 46] Internet-Draft TE YANG Data Model July 2023 description "List of candidate secondary reverse path(s)"; leaf secondary-reverse-path { type leafref { path "../../../../../../" + "te:secondary-reverse-paths/" + "te:secondary-reverse-path/te:name"; } description "A reference to the reverse secondary path when co-routed with the secondary path."; } leaf active { type boolean; config false; description "Indicates an active path that has been selected from the secondary reverse paths list."; } } } } container candidate-secondary-paths { description "The set of candidate secondary paths which may be used for this primary path. When secondary paths are specified in the list the path of the secondary LSP in use must be restricted to those paths referenced. The priority of the secondary paths is specified within the list. Higher priority values are less preferred - that is to say that a path with priority 0 is the most preferred path. In the case that the list is empty, any secondary path may be utilised when the current primary path is in use."; list candidate-secondary-path { key "secondary-path"; ordered-by user; description "List of candidate secondary paths for this tunnel."; leaf secondary-path { type leafref { path "../../../../../te:secondary-paths/" + "te:secondary-path/te:name"; } description Saad, et al. Expires 5 January 2024 [Page 47] Internet-Draft TE YANG Data Model July 2023 "A reference to the secondary path that may be utilised when the containing primary path is in use."; } leaf active { type boolean; config false; description "Indicates an active path that has been selected from the candidate secondary paths."; } } } } } container secondary-paths { description "The set of secondary paths."; reference "RFC4872"; list secondary-path { key "name"; description "List of secondary paths for this tunnel."; uses path-common-properties; leaf preference { type uint8 { range "1..255"; } default "1"; description "Specifies a preference for this path. The lower the number higher the preference."; } leaf secondary-reverse-path { type leafref { path "../../../" + "te:secondary-reverse-paths/" + "te:secondary-reverse-path/te:name"; } description "A reference to the secondary reverse path that may be utilised when the secondary path is in use."; } uses path-compute-info; uses protection-restoration-properties; uses path-state; } } Saad, et al. Expires 5 January 2024 [Page 48] Internet-Draft TE YANG Data Model July 2023 container secondary-reverse-paths { description "The set of secondary reverse paths."; list secondary-reverse-path { key "name"; description "List of secondary paths for this tunnel."; uses path-common-properties; leaf preference { type uint8 { range "1..255"; } default "1"; description "Specifies a preference for this path. The lower the number higher the preference. Paths that have the same preference will be activated together."; } uses path-compute-info; uses protection-restoration-properties; uses path-state; } } action tunnel-action { description "Tunnel action."; input { leaf action-type { type identityref { base te-types:tunnel-action-type; } description "Tunnel action type."; } } output { leaf action-result { type identityref { base te-types:te-action-result; } description "The result of the tunnel action operation."; } } } action protection-external-commands { input { leaf protection-external-command { Saad, et al. Expires 5 January 2024 [Page 49] Internet-Draft TE YANG Data Model July 2023 type identityref { base te-types:protection-external-commands; } description "Protection external command."; } leaf protection-group-ingress-node { type boolean; default "true"; description "When 'true', indicates that the action is applied on ingress node. By default, the action applies to the ingress node only."; } leaf protection-group-egress-node { type boolean; default "false"; description "When set to 'true', indicates that the action is applied on egress node. By default, the action applies to the ingress node only."; } leaf path-name { type string; description "The name of the path that the external command applies to."; } leaf path-type { type te-types:path-type; description "The type of the path that the external command applies to."; } leaf traffic-type { type enumeration { enum normal-traffic { description "The manual-switch or forced-switch command applies to the normal traffic (this Tunnel)."; } enum null-traffic { description "The manual-switch or forced-switch command applies to the null traffic."; } Saad, et al. Expires 5 January 2024 [Page 50] Internet-Draft TE YANG Data Model July 2023 enum extra-traffic { description "The manual-switch or forced-switch command applies to the extra traffic (the extra-traffic Tunnel sharing protection bandwidth with this Tunnel)."; } } description "Indicates whether the manual-switch or forced-switch commands applies to the normal traffic, the null traffic or the extra-traffic."; reference "RFC4427"; } leaf extra-traffic-tunnel-ref { type tunnel-ref; description "In case there are multiple extra-traffic tunnels sharing protection bandwidth with this Tunnel (m:n protection), represents which extra-traffic Tunnel the manual-switch or forced-switch to extra-traffic command applies to."; } } } } } /* TE LSPs Data */ container lsps { config false; description "TE LSPs state container."; list lsp { key "tunnel-name lsp-id node"; unique "source destination tunnel-id lsp-id " + "extended-tunnel-id"; description "List of LSPs associated with the tunnel."; leaf tunnel-name { type string; description "The TE tunnel name."; } leaf lsp-id { type uint16; description "Identifier used in the SENDER_TEMPLATE and the Saad, et al. Expires 5 January 2024 [Page 51] Internet-Draft TE YANG Data Model July 2023 FILTER_SPEC that can be changed to allow a sender to share resources with itself."; reference "RFC3209"; } leaf node { type te-types:te-node-id; description "The node where the TE LSP state resides on."; } leaf source { type te-types:te-node-id; description "Tunnel sender address extracted from SENDER_TEMPLATE object."; reference "RFC3209"; } leaf destination { type te-types:te-node-id; description "The tunnel endpoint address."; reference "RFC3209"; } leaf tunnel-id { type uint16; description "The tunnel identifier that remains constant over the life of the tunnel."; reference "RFC3209"; } leaf extended-tunnel-id { type yang:dotted-quad; description "The LSP Extended Tunnel ID."; reference "RFC3209"; } leaf operational-state { type identityref { base te-types:lsp-state-type; } description "The LSP operational state."; } leaf signaling-type { Saad, et al. Expires 5 January 2024 [Page 52] Internet-Draft TE YANG Data Model July 2023 type identityref { base te-types:path-signaling-type; } description "The signaling protocol used to set up this LSP."; } leaf origin-type { type enumeration { enum ingress { description "Origin ingress."; } enum egress { description "Origin egress."; } enum transit { description "Origin transit."; } } description "The origin of the LSP relative to the location of the local switch in the path."; } leaf lsp-resource-status { type enumeration { enum primary { description "A primary LSP is a fully established LSP for which the resource allocation has been committed at the data plane."; } enum secondary { description "A secondary LSP is an LSP that has been provisioned in the control plane only; e.g. resource allocation has not been committed at the data plane."; } } description "LSP resource allocation state."; reference "RFC4872, section 4.2.1"; } leaf lockout-of-normal { type boolean; description Saad, et al. Expires 5 January 2024 [Page 53] Internet-Draft TE YANG Data Model July 2023 "When set to 'true', it represents a lockout of normal traffic external command. When set to 'false', it represents a clear lockout of normal traffic external command. The lockout of normal traffic command applies to this Tunnel."; reference "RFC4427"; } leaf freeze { type boolean; description "When set to 'true', it represents a freeze external command. When set to 'false', it represents a clear freeze external command. The freeze command applies to all the Tunnels which are sharing the protection resources with this Tunnel."; reference "RFC4427"; } leaf lsp-protection-role { type enumeration { enum working { description "A working LSP must be a primary LSP whilst a protecting LSP can be either a primary or a secondary LSP. Also, known as protected LSPs when working LSPs are associated with protecting LSPs."; } enum protecting { description "A secondary LSP is an LSP that has been provisioned in the control plane only; e.g. resource allocation has not been committed at the data plane."; } } description "LSP role type."; reference "RFC4872, section 4.2.1"; } leaf lsp-protection-state { type identityref { base te-types:lsp-protection-state; } config false; description "The reported protection state controlling which tunnel is using the resources of the protecting LSP."; Saad, et al. Expires 5 January 2024 [Page 54] Internet-Draft TE YANG Data Model July 2023 } leaf protection-group-ingress-node-id { type te-types:te-node-id; description "Indicates the te-node-id of the protection group ingress node when the APS state represents an external command (LoP, SF, MS) applied to it or a WTR timer running on it. If the external command is not applied to the ingress node or the WTR timer is not running on it, this attribute is not specified. A value 0.0.0.0 is used when the te-node-id of the protection group ingress node is unknown (e.g., because the ingress node is outside the scope of control of the server)"; } leaf protection-group-egress-node-id { type te-types:te-node-id; description "Indicates the te-node-id of the protection group egress node when the APS state represents an external command (LoP, SF, MS) applied to it or a WTR timer running on it. If the external command is not applied to the ingress node or the WTR timer is not running on it, this attribute is not specified. A value 0.0.0.0 is used when the te-node-id of the protection group ingress node is unknown (e.g., because the ingress node is outside the scope of control of the server)"; } container lsp-actual-route-information { description "RSVP recorded route object information."; list lsp-actual-route-information { when "../../origin-type = 'ingress'" { description "Applicable on ingress LSPs only."; } key "index"; description "Record route list entry."; uses te-types:record-route-state; } } } } } /* TE Tunnel RPCs/execution Data */ rpc tunnels-path-compute { Saad, et al. Expires 5 January 2024 [Page 55] Internet-Draft TE YANG Data Model July 2023 description "TE tunnels RPC nodes."; input { container path-compute-info { /* * An external path compute module may augment this * target. */ description "RPC input information."; } } output { container path-compute-result { /* * An external path compute module may augment this * target. */ description "RPC output information."; } } } rpc tunnels-actions { description "TE tunnels actions RPC"; input { container tunnel-info { description "TE tunnel information."; choice filter-type { mandatory true; description "Filter choice."; case all-tunnels { leaf all { type empty; mandatory true; description "When present, applies the action on all TE tunnels."; } } case one-tunnel { leaf tunnel { type tunnel-ref; description Saad, et al. Expires 5 January 2024 [Page 56] Internet-Draft TE YANG Data Model July 2023 "Apply action on the specific TE tunnel."; } } } } container action-info { description "TE tunnel action information."; leaf action { type identityref { base te-types:tunnel-action-type; } description "The action type."; } leaf disruptive { when "derived-from-or-self(../action, " + "'te-types:tunnel-action-reoptimize')"; type empty; description "When present, specifies whether or not the reoptimization action is allowed to be disruptive."; } } } output { leaf action-result { type identityref { base te-types:te-action-result; } description "The result of the tunnel action operation."; } } } } Figure 7: TE Tunnel data model YANG module 6. TE Device YANG Model The device TE YANG module ('ietf-te-device') models data that is specific to managing a TE device. This module augments the generic TE YANG module. Saad, et al. Expires 5 January 2024 [Page 57] Internet-Draft TE YANG Data Model July 2023 6.1. Module Structure 6.1.1. TE Interfaces This branch of the model manages TE interfaces that are present on a device. Examples of TE interface properties are: * Maximum reservable bandwidth, bandwidth constraints (BC) * Flooding parameters - Flooding intervals and threshold values * Interface attributes - (Extended) administrative groups - SRLG values - TE metric value * Fast reroute backup tunnel properties (such as static, auto- tunnel) The derived state associated with interfaces is grouped under the interface "state" sub-container as shown in Figure 8. This covers state data such as: * Bandwidth information: maximum bandwidth, available bandwidth at different priorities and for each class-type (CT) * List of admitted LSPs - Name, bandwidth value and pool, time, priority * Statistics: state counters, flooding counters, admission counters (accepted/rejected), preemption counters * Adjacency information - Neighbor address - Metric value Saad, et al. Expires 5 January 2024 [Page 58] Internet-Draft TE YANG Data Model July 2023 module: ietf-te-device augment /te:te: +--rw interfaces . +-- rw te-dev:te-attributes <> . +-- ro state <> Figure 8: TE interface state YANG subtree 6.2. Tree Diagram Figure 9 shows the tree diagram of the device TE YANG model defined in modules 'ietf-te-device.yang'. module: ietf-te-device augment /te:te: +--rw interfaces +--rw threshold-type? enumeration +--rw delta-percentage? rt-types:percentage +--rw threshold-specification? enumeration +--rw up-thresholds* rt-types:percentage +--rw down-thresholds* rt-types:percentage +--rw up-down-thresholds* rt-types:percentage +--rw interface* [interface] +--rw interface if:interface-ref +--rw te-metric? | te-types:te-metric +--rw (admin-group-type)? | +--:(value-admin-groups) | | +--rw (value-admin-group-type)? | | +--:(admin-groups) | | | +--rw admin-group? | | | te-types:admin-group | | +--:(extended-admin-groups) | | {te-types:extended-admin-groups}? | | +--rw extended-admin-group? | | te-types:extended-admin-group | +--:(named-admin-groups) | +--rw named-admin-groups* [named-admin-group] | {te-types:extended-admin-groups, | te-types:named-extended-admin-groups}? | +--rw named-admin-group leafref +--rw (srlg-type)? | +--:(value-srlgs) Saad, et al. Expires 5 January 2024 [Page 59] Internet-Draft TE YANG Data Model July 2023 | | +--rw values* [value] | | +--rw value uint32 | +--:(named-srlgs) | +--rw named-srlgs* [named-srlg] | {te-types:named-srlg-groups}? | +--rw named-srlg leafref +--rw threshold-type? enumeration +--rw delta-percentage? | rt-types:percentage +--rw threshold-specification? enumeration +--rw up-thresholds* | rt-types:percentage +--rw down-thresholds* | rt-types:percentage +--rw up-down-thresholds* | rt-types:percentage +--rw switching-capabilities* [switching-capability] | +--rw switching-capability identityref | +--rw encoding? identityref +--ro te-advertisements-state +--ro flood-interval? uint32 +--ro last-flooded-time? uint32 +--ro next-flooded-time? uint32 +--ro last-flooded-trigger? enumeration +--ro advertised-level-areas* [level-area] +--ro level-area uint32 augment /te:te/te:globals: +--rw lsp-install-interval? uint32 +--rw lsp-cleanup-interval? uint32 +--rw lsp-invalidation-interval? uint32 augment /te:te/te:tunnels/te:tunnel: +--rw path-invalidation-action? identityref +--rw lsp-install-interval? uint32 +--rw lsp-cleanup-interval? uint32 +--rw lsp-invalidation-interval? uint32 augment /te:te/te:lsps/te:lsp: +--ro lsp-timers | +--ro uptime? uint32 | +--ro time-to-install? uint32 | +--ro time-to-destroy? uint32 +--ro downstream-info | +--ro nhop? te-types:te-tp-id | +--ro outgoing-interface? if:interface-ref | +--ro neighbor | | +--ro id? te-gen-node-id | | +--ro type? enumeration | +--ro label? rt-types:generalized-label +--ro upstream-info Saad, et al. Expires 5 January 2024 [Page 60] Internet-Draft TE YANG Data Model July 2023 +--ro phop? te-types:te-tp-id +--ro neighbor | +--ro id? te-gen-node-id | +--ro type? enumeration +--ro label? rt-types:generalized-label rpcs: +---x link-state-update +---w input +---w (filter-type) +--:(match-all) | +---w all empty +--:(match-one-interface) +---w interface? if:interface-ref Figure 9: TE Tunnel device model YANG tree diagram 6.3. YANG Module The device TE YANG module 'ietf-te-device' imports the following module(s): * ietf-interfaces defined in [RFC8343] * ietf-routing-types defined in [RFC8294] * ietf-te-types defined in [RFC8776] * ietf-te defined in this document file "ietf-te-device@2023-06-16.yang" module ietf-te-device { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-te-device"; /* Replace with IANA when assigned */ prefix te-dev; /* Import TE module */ import ietf-te { prefix te; reference "RFCXXXX: A YANG Data Model for Traffic Engineering Tunnels and Interfaces"; } Saad, et al. Expires 5 January 2024 [Page 61] Internet-Draft TE YANG Data Model July 2023 /* Import TE types */ import ietf-te-types { prefix te-types; reference "RFC8776: Common YANG Data Types for Traffic Engineering."; } import ietf-interfaces { prefix if; reference "RFC8343: A YANG Data Model for Interface Management"; } import ietf-routing-types { prefix rt-types; reference "RFC8294: Common YANG Data Types for the Routing Area"; } organization "IETF Traffic Engineering Architecture and Signaling (TEAS) Working Group"; contact "WG Web: WG List: Editor: Tarek Saad Editor: Rakesh Gandhi Editor: Vishnu Pavan Beeram Editor: Himanshu Shah Editor: Xufeng Liu Editor: Igor Bryskin Editor: Oscar Gonzalez de Dios "; description "This module defines a data model for TE device configurations, Saad, et al. Expires 5 January 2024 [Page 62] Internet-Draft TE YANG Data Model July 2023 state, and RPCs. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2023 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX (https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself for full legal notices."; // RFC Ed.: replace XXXX with actual RFC number and remove this // note. // RFC Ed.: update the date below with the date of RFC publication // and remove this note. revision 2023-06-16 { description "Initial revision for the TE device YANG module."; reference "RFCXXXX: A YANG Data Model for Traffic Engineering Tunnels and Interfaces"; } grouping lsp-device-timers { description "Device TE LSP timers configs."; leaf lsp-install-interval { type uint32; units "seconds"; description "TE LSP installation delay time."; } leaf lsp-cleanup-interval { type uint32; units "seconds"; description "TE LSP cleanup delay time."; } leaf lsp-invalidation-interval { type uint32; units "seconds"; Saad, et al. Expires 5 January 2024 [Page 63] Internet-Draft TE YANG Data Model July 2023 description "TE LSP path invalidation before taking action delay time."; } } grouping te-igp-flooding-bandwidth-config { description "Configurable items for igp flooding bandwidth threshold configuration."; leaf threshold-type { type enumeration { enum delta { description "'delta' indicates that the local system should flood IGP updates when a change in reserved bandwidth >= the specified delta occurs on the interface."; } enum threshold-crossed { description "THRESHOLD-CROSSED indicates that the local system should trigger an update (and hence flood) the reserved bandwidth when the reserved bandwidth changes such that it crosses, or becomes equal to one of the threshold values."; } } description "The type of threshold that should be used to specify the values at which bandwidth is flooded. 'delta' indicates that the local system should flood IGP updates when a change in reserved bandwidth >= the specified delta occurs on the interface. Where 'threshold-crossed' is specified, the local system should trigger an update (and hence flood) the reserved bandwidth when the reserved bandwidth changes such that it crosses, or becomes equal to one of the threshold values."; } leaf delta-percentage { when "../threshold-type = 'delta'" { description "The percentage delta can only be specified when the threshold type is specified to be a percentage delta of the reserved bandwidth."; } type rt-types:percentage; description "The percentage of the maximum-reservable-bandwidth Saad, et al. Expires 5 January 2024 [Page 64] Internet-Draft TE YANG Data Model July 2023 considered as the delta that results in an IGP update being flooded."; } leaf threshold-specification { when "../threshold-type = 'threshold-crossed'" { description "The selection of whether mirrored or separate threshold values are to be used requires user specified thresholds to be set."; } type enumeration { enum mirrored-up-down { description "mirrored-up-down indicates that a single set of threshold values should be used for both increasing and decreasing bandwidth when determining whether to trigger updated bandwidth values to be flooded in the IGP TE extensions."; } enum separate-up-down { description "separate-up-down indicates that a separate threshold values should be used for the increasing and decreasing bandwidth when determining whether to trigger updated bandwidth values to be flooded in the IGP TE extensions."; } } description "This value specifies whether a single set of threshold values should be used for both increasing and decreasing bandwidth when determining whether to trigger updated bandwidth values to be flooded in the IGP TE extensions. 'mirrored-up-down' indicates that a single value (or set of values) should be used for both increasing and decreasing values, where 'separate-up-down' specifies that the increasing and decreasing values will be separately specified."; } leaf-list up-thresholds { when "../threshold-type = 'threshold-crossed'" + "and ../threshold-specification = 'separate-up-down'" { description "A list of up-thresholds can only be specified when the bandwidth update is triggered based on crossing a threshold and separate up and down thresholds are required."; } Saad, et al. Expires 5 January 2024 [Page 65] Internet-Draft TE YANG Data Model July 2023 type rt-types:percentage; description "The thresholds (expressed as a percentage of the maximum reservable bandwidth) at which bandwidth updates are to be triggered when the bandwidth is increasing."; } leaf-list down-thresholds { when "../threshold-type = 'threshold-crossed'" + "and ../threshold-specification = 'separate-up-down'" { description "A list of down-thresholds can only be specified when the bandwidth update is triggered based on crossing a threshold and separate up and down thresholds are required."; } type rt-types:percentage; description "The thresholds (expressed as a percentage of the maximum reservable bandwidth) at which bandwidth updates are to be triggered when the bandwidth is decreasing."; } leaf-list up-down-thresholds { when "../threshold-type = 'threshold-crossed'" + "and ../threshold-specification = 'mirrored-up-down'" { description "A list of thresholds corresponding to both increasing and decreasing bandwidths can be specified only when an update is triggered based on crossing a threshold, and the same up and down thresholds are required."; } type rt-types:percentage; description "The thresholds (expressed as a percentage of the maximum reservable bandwidth of the interface) at which bandwidth updates are flooded - used both when the bandwidth is increasing and decreasing."; } } /** * TE device augmentations */ augment "/te:te" { description "TE global container."; /* TE Interface Configuration Data */ container interfaces { description Saad, et al. Expires 5 January 2024 [Page 66] Internet-Draft TE YANG Data Model July 2023 "Configuration data model for TE interfaces."; uses te-igp-flooding-bandwidth-config; list interface { key "interface"; description "TE interfaces."; leaf interface { type if:interface-ref; description "TE interface name."; } /* TE interface parameters */ leaf te-metric { type te-types:te-metric; description "TE interface metric."; } choice admin-group-type { description "TE interface administrative groups representation type."; case value-admin-groups { choice value-admin-group-type { description "choice of admin-groups."; case admin-groups { description "Administrative group/Resource class/Color."; leaf admin-group { type te-types:admin-group; description "TE interface administrative group."; } } case extended-admin-groups { if-feature "te-types:extended-admin-groups"; description "Extended administrative group/Resource class/Color."; leaf extended-admin-group { type te-types:extended-admin-group; description "TE interface extended administrative group."; } } } } Saad, et al. Expires 5 January 2024 [Page 67] Internet-Draft TE YANG Data Model July 2023 case named-admin-groups { list named-admin-groups { if-feature "te-types:extended-admin-groups"; if-feature "te-types:named-extended-admin-groups"; key "named-admin-group"; description "A list of named admin-group entries."; leaf named-admin-group { type leafref { path "../../../../te:globals/" + "te:named-admin-groups/te:named-admin-group/" + "te:name"; } description "A named admin-group entry."; } } } } choice srlg-type { description "Choice of SRLG configuration."; case value-srlgs { list values { key "value"; description "List of SRLG values that this link is part of."; leaf value { type uint32 { range "0..4294967295"; } description "Value of the SRLG"; } } } case named-srlgs { list named-srlgs { if-feature "te-types:named-srlg-groups"; key "named-srlg"; description "A list of named SRLG entries."; leaf named-srlg { type leafref { path "../../../../te:globals/" + "te:named-srlgs/te:named-srlg/te:name"; } Saad, et al. Expires 5 January 2024 [Page 68] Internet-Draft TE YANG Data Model July 2023 description "A named SRLG entry."; } } } } uses te-igp-flooding-bandwidth-config; list switching-capabilities { key "switching-capability"; description "List of interface capabilities for this interface."; leaf switching-capability { type identityref { base te-types:switching-capabilities; } description "Switching Capability for this interface."; } leaf encoding { type identityref { base te-types:lsp-encoding-types; } description "Encoding supported by this interface."; } } container te-advertisements-state { config false; description "TE interface advertisements state container."; leaf flood-interval { type uint32; description "The periodic flooding interval."; } leaf last-flooded-time { type uint32; units "seconds"; description "Time elapsed since last flooding in seconds."; } leaf next-flooded-time { type uint32; units "seconds"; description "Time remained for next flooding in seconds."; } leaf last-flooded-trigger { Saad, et al. Expires 5 January 2024 [Page 69] Internet-Draft TE YANG Data Model July 2023 type enumeration { enum link-up { description "Link-up flooding trigger."; } enum link-down { description "Link-down flooding trigger."; } enum threshold-up { description "Bandwidth reservation up threshold."; } enum threshold-down { description "Bandwidth reservation down threshold."; } enum bandwidth-change { description "Bandwidth capacity change."; } enum user-initiated { description "Initiated by user."; } enum srlg-change { description "SRLG property change."; } enum periodic-timer { description "Periodic timer expired."; } } default "periodic-timer"; description "Trigger for the last flood."; } list advertised-level-areas { key "level-area"; description "List of level-areas that the TE interface is advertised in."; leaf level-area { type uint32; description "The IGP area or level where the TE interface link state is advertised in."; Saad, et al. Expires 5 January 2024 [Page 70] Internet-Draft TE YANG Data Model July 2023 } } } } } } /* TE globals device augmentation */ augment "/te:te/te:globals" { description "Global TE device specific configuration parameters."; uses lsp-device-timers; } /* TE tunnels device configuration augmentation */ augment "/te:te/te:tunnels/te:tunnel" { description "Tunnel device dependent augmentation."; leaf path-invalidation-action { type identityref { base te-types:path-invalidation-action-type; } description "Tunnel path invalidation action."; } uses lsp-device-timers; } /* TE LSPs device state augmentation */ augment "/te:te/te:lsps/te:lsp" { description "TE LSP device dependent augmentation."; container lsp-timers { when "../te:origin-type = 'ingress'" { description "Applicable to ingress LSPs only."; } description "Ingress LSP timers."; leaf uptime { type uint32; units "seconds"; description "The LSP uptime."; } Saad, et al. Expires 5 January 2024 [Page 71] Internet-Draft TE YANG Data Model July 2023 leaf time-to-install { type uint32; units "seconds"; description "The time remaining for a new LSP to be instantiated in forwarding to carry traffic."; } leaf time-to-destroy { type uint32; units "seconds"; description "The time remaining for a existing LSP to be deleted from forwarding."; } } container downstream-info { when "../te:origin-type != 'egress'" { description "Downstream information of the LSP."; } description "downstream information."; leaf nhop { type te-types:te-tp-id; description "downstream next-hop address."; } leaf outgoing-interface { type if:interface-ref; description "downstream interface."; } container neighbor { uses te:te-generic-node-id; description "downstream neighbor address."; } leaf label { type rt-types:generalized-label; description "downstream label."; } } container upstream-info { when "../te:origin-type != 'ingress'" { description "Upstream information of the LSP."; } Saad, et al. Expires 5 January 2024 [Page 72] Internet-Draft TE YANG Data Model July 2023 description "upstream information."; leaf phop { type te-types:te-tp-id; description "upstream next-hop or previous-hop address."; } container neighbor { uses te:te-generic-node-id; description "upstream neighbor address."; } leaf label { type rt-types:generalized-label; description "upstream label."; } } } /* TE interfaces RPCs/execution Data */ rpc link-state-update { description "Triggers a link state update for the specific interface."; input { choice filter-type { mandatory true; description "Filter choice."; case match-all { leaf all { type empty; mandatory true; description "Match all TE interfaces."; } } case match-one-interface { leaf interface { type if:interface-ref; description "Match a specific TE interface."; } } } } } Saad, et al. Expires 5 January 2024 [Page 73] Internet-Draft TE YANG Data Model July 2023 } Figure 10: TE device data model YANG module 7. Notifications Notifications are a key component of any topology data model. [RFC8639] and [RFC8641] define a subscription mechanism and a push mechanism for YANG datastores. These mechanisms currently allow the user to: * Subscribe to notifications on a per-client basis. * Specify subtree filters or XML Path Language (XPath) filters so that only contents of interest will be sent. * Specify either periodic or on-demand notifications. 8. IANA Considerations This document registers the following URIs in the IETF XML registry [RFC3688]. Following the format in [RFC3688], the following registrations are requested to be made. URI: urn:ietf:params:xml:ns:yang:ietf-te Registrant Contact: The IESG. XML: N/A, the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-te-device Registrant Contact: The IESG. XML: N/A, the requested URI is an XML namespace. This document registers two YANG modules in the YANG Module Names registry [RFC6020]. Name: ietf-te Namespace: urn:ietf:params:xml:ns:yang:ietf-te Prefix: te Reference: RFCXXXX Name: ietf-te-device Namespace: urn:ietf:params:xml:ns:yang:ietf-te-device Prefix: te-device Reference: RFCXXXX Saad, et al. Expires 5 January 2024 [Page 74] Internet-Draft TE YANG Data Model July 2023 9. Security Considerations The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446]. The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content. There are a number of data nodes defined in this YANG module that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability: "/te/globals": This module specifies the global TE configurations on a device. Unauthorized access to this container could cause the device to ignore packets it should receive and process. "/te/tunnels": This list specifies the configuration and state of TE Tunnels present on the device or controller. Unauthorized access to this list could cause the device to ignore packets it should receive and process. An attacker may also use state to derive information about the network topology, and subsequently orchestrate further attacks. "/te/interfaces": This list specifies the configuration and state TE interfaces on a device. Unauthorized access to this list could cause the device to ignore packets it should receive and process. Some of the readable data nodes in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes. These are the subtrees and data nodes and their sensitivity/vulnerability: "/te/lsps": this list contains information state about established LSPs in the network. An attacker can use this information to derive information about the network topology, and subsequently orchestrate further attacks. Saad, et al. Expires 5 January 2024 [Page 75] Internet-Draft TE YANG Data Model July 2023 Some of the RPC operations in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control access to these operations. These are the operations and their sensitivity/vulnerability: "/te/tunnels-actions": using this RPC, an attacker can modify existing paths that may be carrying live traffic, and hence result to interruption to services carried over the network. "/te/tunnels-path-compute": using this RPC, an attacker can retrieve secured information about the network provider which can be used to orchestrate further attacks. The security considerations spelled out in the YANG 1.1 specification [RFC7950] apply for this document as well. 10. Acknowledgement The authors would like to thank the members of the multi-vendor YANG design team who are involved in the definition of this model. The authors would like to thank Tom Petch and Adrian Farrel for reviewing and providing useful feedback about the document. The authors would also like to thank Loa Andersson, Lou Berger, Sergio Belotti, Italo Busi, Carlo Perocchio, Francesco Lazzeri, Aihua Guo, Dhruv Dhody, and Raqib Jones for providing feedback on this document. 11. Contributors Himanshu Shah Ciena Email: hshah@ciena.com Xia Chen Huawei Technologies Email: jescia.chenxia@huawei.com Bin Wen Comcast Email: Bin_Wen@cable.comcast.com Saad, et al. Expires 5 January 2024 [Page 76] Internet-Draft TE YANG Data Model July 2023 12. Appendix A: Data Tree Examples This section contains examples of use of the model with RESTCONF [RFC8040] and JSON encoding. For the example we will use a 4 node MPLS network were RSVP-TE MPLS Tunnels can be setup. The loopbacks of each router are shown. The network in Figure 11 will be used in the examples described in the following sections. 192.0.2.1 192.0.2.2 192.0.2.4 +-------+ +-------+ +-------+ | | | | | | | A +--------+ B +------+ D | +---+---+ +-------+ +---+---+ | | | +-------+ | | | | | +------------+ C +----------+ | | +-------+ 192.0.2.3 Figure 11: TE network used in data tree examples 12.1. Basic Tunnel Setup This example uses the TE Tunnel YANG data model defined in this document to create an RSVP-TE signaled Tunnel of packet LSP encoding type. First, the TE Tunnel is created with no specific restrictions or constraints (e.g., protection or restoration). The TE Tunnel ingresses on router A and egresses on router D. In this case, the TE Tunnel is created without specifying additional information about the primary paths. Saad, et al. Expires 5 January 2024 [Page 77] Internet-Draft TE YANG Data Model July 2023 POST /restconf/data/ietf-te:te/tunnels HTTP/1.1 Host: example.com Accept: application/yang-data+json Content-Type: application/yang-data+json { "ietf-te:tunnel": [ { "name": "Example_LSP_Tunnel_A_2", "encoding": "te-types:lsp-encoding-packet", "admin-state": "te-types:tunnel-state-up", "source": "192.0.2.1", "destination": "192.0.2.4", "bidirectional": "false", "signaling-type": "te-types:path-setup-rsvp" } ] } 12.2. Global Named Path Constraints This example uses the YANG data model to create a 'named path constraint' that can be reference by TE Tunnels. The path constraint, in this case, limits the TE Tunnel hops for the computed path. POST /restconf/data/ietf-te:te/globals/named-path-constraints HTTP/1.1 Host: example.com Accept: application/yang-data+json Content-Type: application/yang-data+json "ietf-te:named-path-constraint": { "name": "max-hop-3", "path-metric-bounds": { "path-metric-bound": { "metric-type": "te-types:path-metric-hop", "upper-bound": "3" } } } } 12.3. Tunnel with Global Path Constraint In this example, the previously created 'named path constraint' is applied to the TE Tunnel created in Section 12.1. Saad, et al. Expires 5 January 2024 [Page 78] Internet-Draft TE YANG Data Model July 2023 POST /restconf/data/ietf-te:te/tunnels HTTP/1.1 Host: example.com Accept: application/yang-data+json Content-Type: application/yang-data+json { "ietf-te:ietf-tunnel": [ { "name": "Example_LSP_Tunnel_A_4_1", "encoding": "te-types:lsp-encoding-packet", "description": "Simple_LSP_with_named_path", "admin-state": "te-types:tunnel-state-up", "source": "192.0.2.1", "destination": "192.0.2.4", "signaling-type": "path-setup-rsvp", "primary-paths": [ { "primary-path": { "name": "Simple_LSP_1", "use-path-computation": "true", "named-path-constraint": "max-hop-3" } } ] } ] } 12.4. Tunnel with Per-tunnel Path Constraint In this example, the a per tunnel path constraint is explicitly indicated under the TE Tunnel created in Section 12.1 to constrain the computed path for the tunnel. Saad, et al. Expires 5 January 2024 [Page 79] Internet-Draft TE YANG Data Model July 2023 POST /restconf/data/ietf-te:te/tunnels HTTP/1.1 Host: example.com Accept: application/yang-data+json Content-Type: application/yang-data+json { "ietf-te:tunnel": [ { "name": "Example_LSP_Tunnel_A_4_2", "encoding": "te-types:lsp-encoding-packet", "admin-state": "te-types:tunnel-state-up", "source": "192.0.2.1", "destination": "192.0.2.4", "signaling-type": "te-types:path-setup-rsvp", "primary-paths": { "primary-path": [ { "name": "path1", "path-metric-bounds": { "path-metric-bound": [ { "metric-type": "te-types:path-metric-hop", "upper-bound": "3" } ] } } ] } } ] } 12.5. Tunnel State In this example, the 'GET' query is sent to return the state stored about the tunnel. GET /restconf/data/ietf-te:te/tunnels + /tunnel="Example_LSP_Tunnel_A_4_1" /p2p-primary-paths/ HTTP/1.1 Host: example.com Accept: application/yang-data+json The request, with status code 200 would include, for example, the following json: Saad, et al. Expires 5 January 2024 [Page 80] Internet-Draft TE YANG Data Model July 2023 { "ietf-te:primary-paths": { "primary-path": [ { "name": "path1", "path-computation-method": "te-types:path-locally-computed", "computed-paths-properties": { "computed-path-properties": [ { "k-index": "1", "path-properties": { "path-route-objects": { "path-route-object": [ { "index": "1", "numbered-node-hop": { "node-id": "192.0.2.2" } }, { "index": "2", "numbered-node-hop": { "node-id": "192.0.2.4" } } ] } } } ] }, "lsps": { "lsp": [ { "tunnel-name": "Example_LSP_Tunnel_A_4_1", "node": "192.0.2.1 ", "lsp-id": "25356" } ] } } ] } } 12.6. Example TE Tunnel with Primary and Secondary Paths Saad, et al. Expires 5 January 2024 [Page 81] Internet-Draft TE YANG Data Model July 2023 +----------+ +----------+ +-|192.0.2.9 |---+ |192.0.2.10| | +----------+ | +----------+ | | | | +----------+ +----------+ +----------+ | | |192.0.2.8 |----|192.0.2.3 |-----|192.0.2.4 |----+ | +----------+ +----------+ +----------+ | | | | | +----------+ | | | |192.0.2.1 |---------+ | +----------+ +----------+ +-----------|192.0.2.5 | | | +----------+ | | +----------+ | | | +--------------|192.0.2.2 |---------------------+ | | +----------+ | | | | | +----------+ | | +----------+ |192.0.2.6 |----------------+ +-------------------|192.0.2.7 | +----------+ +----------+ Figure 12: TE network used in data tree examples Below is the state retrieved for a TE tunnel from source 192.0.2.1 to 192.0.2.5 with primary, secondary, reverse, and secondary reverse paths as shown in Figure 12. { "ietf-te:te": { "tunnels": { "tunnel": [ { "name": "example-1", "description": "Example in slide 1", "source": "192.0.2.1", "destination": "192.0.2.5", "bidirectional": false, "primary-paths": { "primary-path": [ { "name": "primary-1 (fwd)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.2", "hop-type": "loose" } Saad, et al. Expires 5 January 2024 [Page 82] Internet-Draft TE YANG Data Model July 2023 } ] }, "primary-reverse-path": { "name": "primary-2 (rev)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.3", "hop-type": "loose" } } ] }, "candidate-secondary-reverse-paths": { "candidate-secondary-reverse-path": [ "secondary-3 (rev)", "secondary-4 (rev)", "secondary-5 (rev)" ] } }, "candidate-secondary-paths": { "candidate-secondary-path": [ "secondary-1 (fwd)", "secondary-2 (fwd)" ] } } ] }, "secondary-paths": { "secondary-path": [ { "name": "secondary-1 (fwd)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.1" } }, { "index": 2, "numbered-node-hop": { Saad, et al. Expires 5 January 2024 [Page 83] Internet-Draft TE YANG Data Model July 2023 "node-id": "192.0.2.2", "hop-type": "loose" } } ] } }, { "name": "secondary-2 (fwd)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.2" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.5", "hop-type": "loose" } } ] } } ] }, "secondary-reverse-paths": { "secondary-reverse-path": [ { "name": "secondary-3 (rev)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.5" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.4", "hop-type": "loose" } } Saad, et al. Expires 5 January 2024 [Page 84] Internet-Draft TE YANG Data Model July 2023 ] } }, { "name": "secondary-4 (rev)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.4" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.3", "hop-type": "loose" } } ] } }, { "name": "secondary-5 (rev)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.3" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.1", "hop-type":"loose" } } ] } } ] } }, { "name": "example-3", Saad, et al. Expires 5 January 2024 [Page 85] Internet-Draft TE YANG Data Model July 2023 "description": "Example in slide 3", "source": "192.0.2.1", "destination": "192.0.2.5", "bidirectional": true, "primary-paths": { "primary-path": [ { "name": "primary-1 (bidir)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.2", "hop-type": "loose" } } ] }, "candidate-secondary-paths": { "candidate-secondary-path": [ "secondary-1 (bidir)", "secondary-2 (bidir)" ] } } ] }, "secondary-paths": { "secondary-path": [ { "name": "secondary-1 (bidir)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.1" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.2", "hop-type": "loose" } } ] Saad, et al. Expires 5 January 2024 [Page 86] Internet-Draft TE YANG Data Model July 2023 } }, { "name": "secondary-2 (bidir)", "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.2" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.5", "hop-type": "loose" } } ] } } ] } }, { "name": "example-4", "description": "Example in slide 4", "source": "192.0.2.1", "destination": "192.0.2.5", "bidirectional": false, "primary-paths": { "primary-path": [ { "name": "primary-1 (fwd)", "co-routed": [null], "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.2", "hop-type": "loose" } } ] }, "primary-reverse-path": { Saad, et al. Expires 5 January 2024 [Page 87] Internet-Draft TE YANG Data Model July 2023 "name": "primary-2 (rev)", "candidate-secondary-reverse-paths": { "candidate-secondary-reverse-path": [ "secondary-3 (rev)", "secondary-4 (rev)" ] } }, "candidate-secondary-paths": { "candidate-secondary-path": [ "secondary-1 (fwd)", "secondary-2 (fwd)" ] } } ] }, "secondary-paths": { "secondary-path": [ { "name": "secondary-1 (fwd)", "co-routed": [null], "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { "node-id": "192.0.2.1" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.2", "hop-type": "loose" } } ] } }, { "name": "secondary-2 (fwd)", "co-routed": [null], "explicit-route-objects-always": { "route-object-include-exclude": [ { "index": 1, "numbered-node-hop": { Saad, et al. Expires 5 January 2024 [Page 88] Internet-Draft TE YANG Data Model July 2023 "node-id": "192.0.2.2" } }, { "index": 2, "numbered-node-hop": { "node-id": "192.0.2.5", "hop-type": "loose" } } ] } } ] }, "secondary-reverse-paths": { "secondary-reverse-path": [ { "name": "secondary-3 (rev)" }, { "name": "secondary-4 (rev)" } ] } } ] } } } 13. Appendix B: Full Model Tree Diagram Figure 13 shows the full tree diagram of the TE YANG model defined in module 'ietf-te.yang'. module: ietf-te +--rw te +--rw enable? boolean +--rw globals | +--rw named-admin-groups | | +--rw named-admin-group* [name] | | {te-types:extended-admin-groups, | | te-types:named-extended-admin-groups}? | | +--rw name string | | +--rw bit-position? uint32 | +--rw named-srlgs | | +--rw named-srlg* [name] {te-types:named-srlg-groups}? Saad, et al. Expires 5 January 2024 [Page 89] Internet-Draft TE YANG Data Model July 2023 | | +--rw name string | | +--rw value? te-types:srlg | | +--rw cost? uint32 | +--rw named-path-constraints | +--rw named-path-constraint* [name] | {te-types:named-path-constraints}? | +--rw name string | +---u path-constraints-common +--rw tunnels | +--rw tunnel* [name] | +--rw name string | +--rw alias? string | +--rw identifier? uint32 | +--rw color? uint32 | +--rw description? string | +--rw admin-state? identityref | +--ro operational-state? identityref | +---u te-types:encoding-and-switching-type | +---u tunnel-common-attributes | +--rw controller | | +--rw protocol-origin? identityref | | +--rw controller-entity-id? string | +--rw reoptimize-timer? uint16 | +---u tunnel-associations-properties | +---u protection-restoration-properties | +---u te-types:tunnel-constraints | +---u tunnel-hierarchy-properties | +--rw primary-paths | | +--rw primary-path* [name] | | +--ro active? boolean | | +---u path-common-properties | | +---u path-forward-properties | | +---u k-requested-paths | | +---u path-compute-info | | +---u path-state | | +--rw primary-reverse-path | | | +---u path-common-properties | | | +---u path-compute-info | | | +---u path-state | | | +--rw candidate-secondary-reverse-paths | | | +--rw candidate-secondary-reverse-path* | | | [secondary-reverse-path] | | | +--rw secondary-reverse-path leafref | | | +--ro active? boolean | | +--rw candidate-secondary-paths | | +--rw candidate-secondary-path* [secondary-path] | | +--rw secondary-path leafref | | +--ro active? boolean Saad, et al. Expires 5 January 2024 [Page 90] Internet-Draft TE YANG Data Model July 2023 | +--rw secondary-paths | | +--rw secondary-path* [name] | | +---u path-common-properties | | +--rw preference? uint8 | | +--rw secondary-reverse-path? leafref | | +---u path-compute-info | | +---u protection-restoration-properties | | +---u path-state | +--rw secondary-reverse-paths | | +--rw secondary-reverse-path* [name] | | +---u path-common-properties | | +--rw preference? uint8 | | +---u path-compute-info | | +---u protection-restoration-properties | | +---u path-state | +---x tunnel-action | | +---w input | | | +---w action-type? identityref | | +--ro output | | +--ro action-result? identityref | +---x protection-external-commands | +---w input | +---w protection-external-command? identityref | +---w protection-group-ingress-node? boolean | +---w protection-group-egress-node? boolean | +---w path-name? string | +---w path-type? | | te-types:path-type | +---w traffic-type? enumeration | +---w extra-traffic-tunnel-ref? tunnel-ref +--ro lsps +--ro lsp* [tunnel-name lsp-id node] +--ro tunnel-name string +--ro lsp-id uint16 +--ro node | te-types:te-node-id +--ro source? | te-types:te-node-id +--ro destination? | te-types:te-node-id +--ro tunnel-id? uint16 +--ro extended-tunnel-id? yang:dotted-quad +--ro operational-state? identityref +--ro signaling-type? identityref +--ro origin-type? enumeration +--ro lsp-resource-status? enumeration +--ro lockout-of-normal? boolean +--ro freeze? boolean Saad, et al. Expires 5 January 2024 [Page 91] Internet-Draft TE YANG Data Model July 2023 +--ro lsp-protection-role? enumeration +--ro lsp-protection-state? identityref +--ro protection-group-ingress-node-id? | te-types:te-node-id +--ro protection-group-egress-node-id? | te-types:te-node-id +--ro lsp-actual-route-information +--ro lsp-actual-route-information* [index] +---u te-types:record-route-state rpcs: +---x tunnels-path-compute | +---w input | | +---w path-compute-info | +--ro output | +--ro path-compute-result +---x tunnels-actions +---w input | +---w tunnel-info | | +---w (filter-type) | | +--:(all-tunnels) | | | +---w all empty | | +--:(one-tunnel) | | +---w tunnel? tunnel-ref | +---w action-info | +---w action? identityref | +---w disruptive? empty +--ro output +--ro action-result? identityref grouping te-generic-node-id: +-- id? te-gen-node-id +-- type? enumeration grouping path-common-properties: +-- name? string +-- path-computation-method? identityref +-- path-computation-server | +---u te-generic-node-id +-- compute-only? empty +-- use-path-computation? boolean +-- lockdown? empty +--ro path-scope? identityref grouping path-compute-info: +---u tunnel-associations-properties +---u te-types:generic-path-optimization +-- named-path-constraint? leafref | {te-types:named-path-constraints}? +---u path-constraints-common Saad, et al. Expires 5 January 2024 [Page 92] Internet-Draft TE YANG Data Model July 2023 grouping path-forward-properties: +-- preference? uint8 +-- co-routed? boolean grouping k-requested-paths: +-- k-requested-paths? uint8 grouping path-state: +---u path-computation-response +--ro lsp-provisioning-error-infos | +--ro lsp-provisioning-error-info* [] | +--ro error-reason? identityref | +--ro error-description? string | +--ro error-timestamp? yang:date-and-time | +--ro error-node-id? te-types:te-node-id | +--ro error-link-id? te-types:te-tp-id | +--ro lsp-id? uint16 +--ro lsps +--ro lsp* [node lsp-id] +--ro tunnel-name? -> /te/lsps/lsp/tunnel-name +--ro node? leafref +--ro lsp-id? leafref grouping path-computation-response: +--ro computed-paths-properties | +--ro computed-path-properties* [k-index] | +--ro k-index? uint8 | +---u te-types:generic-path-properties +--ro computed-path-error-infos +--ro computed-path-error-info* [] +--ro error-description? string +--ro error-timestamp? yang:date-and-time +--ro error-reason? identityref grouping protection-restoration-properties: +-- protection | +-- protection-type? identityref | +-- protection-reversion-disable? boolean | +-- hold-off-time? uint32 | +-- wait-to-revert? uint16 | +-- aps-signal-id? uint8 +-- restoration +-- restoration-type? identityref +-- restoration-scheme? identityref +-- restoration-reversion-disable? boolean +-- hold-off-time? uint32 +-- wait-to-restore? uint16 +-- wait-to-revert? uint16 grouping tunnel-associations-properties: +-- association-objects +-- association-object* [association-key] | +-- association-key? string Saad, et al. Expires 5 January 2024 [Page 93] Internet-Draft TE YANG Data Model July 2023 | +-- type? identityref | +-- id? uint16 | +-- source | +---u te-generic-node-id +-- association-object-extended* [association-key] +-- association-key? string +-- type? identityref +-- id? uint16 +-- source | +---u te-generic-node-id +-- global-source? uint32 +-- extended-id? yang:hex-string grouping tunnel-end-point: +-- node-id? nw:node-id +-- te-node-id? te-types:te-node-id +-- tunnel-tp-id? binary grouping tunnel-common-attributes: +-- source | +---u tunnel-end-point +-- destination | +---u tunnel-end-point +-- bidirectional? boolean grouping tunnel-hierarchy-properties: +-- hierarchy +-- dependency-tunnels | +-- dependency-tunnel* [name] | +-- name? | | -> /te/tunnels/tunnel/name | +---u te-types:encoding-and-switching-type +-- hierarchical-link +-- enable? boolean +-- local-node-id? nw:node-id +-- local-te-node-id? te-types:te-node-id +-- local-link-tp-id? nt:tp-id +-- local-te-link-tp-id? te-types:te-tp-id +-- remote-link-tp-id? nt:tp-id +-- remote-te-node-id? te-types:te-node-id +-- network-id? nw:network-id +---u te-types:te-topology-identifier grouping path-constraints-common: +---u te-types:common-path-constraints-attributes +---u te-types:generic-path-disjointness +---u te-types:path-constraints-route-objects +-- path-in-segment! | +---u te-types:label-set-info +-- path-out-segment! +---u te-types:label-set-info Saad, et al. Expires 5 January 2024 [Page 94] Internet-Draft TE YANG Data Model July 2023 Figure 13: Full tree diagram of TE Tunnel YANG data model 14. References 14.1. Normative References [ITU_G.808.1] ITU-T Recommendation G.808.1, "Generic protection switching - Linear trail and subnetwork protection", ITU-T G.808.1 , May 2014. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001, . [RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol- Traffic Engineering (RSVP-TE) Extensions", RFC 3473, DOI 10.17487/RFC3473, January 2003, . [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004, . [RFC4206] Kompella, K. and Y. Rekhter, "Label Switched Paths (LSP) Hierarchy with Generalized Multi-Protocol Label Switching (GMPLS) Traffic Engineering (TE)", RFC 4206, DOI 10.17487/RFC4206, October 2005, . [RFC4427] Mannie, E., Ed. and D. Papadimitriou, Ed., "Recovery (Protection and Restoration) Terminology for Generalized Multi-Protocol Label Switching (GMPLS)", RFC 4427, DOI 10.17487/RFC4427, March 2006, . [RFC4872] Lang, J.P., Ed., Rekhter, Y., Ed., and D. Papadimitriou, Ed., "RSVP-TE Extensions in Support of End-to-End Generalized Multi-Protocol Label Switching (GMPLS) Recovery", RFC 4872, DOI 10.17487/RFC4872, May 2007, . Saad, et al. Expires 5 January 2024 [Page 95] Internet-Draft TE YANG Data Model July 2023 [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010, . [RFC6107] Shiomoto, K., Ed. and A. Farrel, Ed., "Procedures for Dynamically Signaled Hierarchical Label Switched Paths", RFC 6107, DOI 10.17487/RFC6107, February 2011, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011, . [RFC6780] Berger, L., Le Faucheur, F., and A. Narayanan, "RSVP ASSOCIATION Object Extensions", RFC 6780, DOI 10.17487/RFC6780, October 2012, . [RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013, . [RFC7271] Ryoo, J., Ed., Gray, E., Ed., van Helvoort, H., D'Alessandro, A., Cheung, T., and E. Osborne, "MPLS Transport Profile (MPLS-TP) Linear Protection to Match the Operational Expectations of Synchronous Digital Hierarchy, Optical Transport Network, and Ethernet Transport Network Operators", RFC 7271, DOI 10.17487/RFC7271, June 2014, . [RFC7308] Osborne, E., "Extended Administrative Groups in MPLS Traffic Engineering (MPLS-TE)", RFC 7308, DOI 10.17487/RFC7308, July 2014, . [RFC7471] Giacalone, S., Ward, D., Drake, J., Atlas, A., and S. Previdi, "OSPF Traffic Engineering (TE) Metric Extensions", RFC 7471, DOI 10.17487/RFC7471, March 2015, . Saad, et al. Expires 5 January 2024 [Page 96] Internet-Draft TE YANG Data Model July 2023 [RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016, . [RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8232] Crabbe, E., Minei, I., Medved, J., Varga, R., Zhang, X., and D. Dhody, "Optimizations of Label Switched Path State Synchronization Procedures for a Stateful PCE", RFC 8232, DOI 10.17487/RFC8232, September 2017, . [RFC8234] Ryoo, J., Cheung, T., van Helvoort, H., Busi, I., and G. Wen, "Updates to MPLS Transport Profile (MPLS-TP) Linear Protection in Automatic Protection Switching (APS) Mode", RFC 8234, DOI 10.17487/RFC8234, August 2017, . [RFC8294] Liu, X., Qu, Y., Lindem, A., Hopps, C., and L. Berger, "Common YANG Data Types for the Routing Area", RFC 8294, DOI 10.17487/RFC8294, December 2017, . [RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018, . [RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, March 2018, . [RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018, . [RFC8343] Bjorklund, M., "A YANG Data Model for Interface Management", RFC 8343, DOI 10.17487/RFC8343, March 2018, . Saad, et al. Expires 5 January 2024 [Page 97] Internet-Draft TE YANG Data Model July 2023 [RFC8345] Clemm, A., Medved, J., Varga, R., Bahadur, N., Ananthakrishnan, H., and X. Liu, "A YANG Data Model for Network Topologies", RFC 8345, DOI 10.17487/RFC8345, March 2018, . [RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018, . [RFC8570] Ginsberg, L., Ed., Previdi, S., Ed., Giacalone, S., Ward, D., Drake, J., and Q. Wu, "IS-IS Traffic Engineering (TE) Metric Extensions", RFC 8570, DOI 10.17487/RFC8570, March 2019, . [RFC8639] Voit, E., Clemm, A., Gonzalez Prieto, A., Nilsen-Nygaard, E., and A. Tripathy, "Subscription to YANG Notifications", RFC 8639, DOI 10.17487/RFC8639, September 2019, . [RFC8641] Clemm, A. and E. Voit, "Subscription to YANG Notifications for Datastore Updates", RFC 8641, DOI 10.17487/RFC8641, September 2019, . [RFC8776] Saad, T., Gandhi, R., Liu, X., Beeram, V., and I. Bryskin, "Common YANG Data Types for Traffic Engineering", RFC 8776, DOI 10.17487/RFC8776, June 2020, . [RFC8795] Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H., and O. Gonzalez de Dios, "YANG Data Model for Traffic Engineering (TE) Topologies", RFC 8795, DOI 10.17487/RFC8795, August 2020, . [RFC9012] Patel, K., Van de Velde, G., Sangli, S., and J. Scudder, "The BGP Tunnel Encapsulation Attribute", RFC 9012, DOI 10.17487/RFC9012, April 2021, . 14.2. Informative References [rfc3473] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol- Traffic Engineering (RSVP-TE) Extensions", RFC 3473, DOI 10.17487/RFC3473, January 2003, . Saad, et al. Expires 5 January 2024 [Page 98] Internet-Draft TE YANG Data Model July 2023 [RFC3945] Mannie, E., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Architecture", RFC 3945, DOI 10.17487/RFC3945, October 2004, . [RFC9256] Filsfils, C., Talaulikar, K., Ed., Voyer, D., Bogdanov, A., and P. Mattes, "Segment Routing Policy Architecture", RFC 9256, DOI 10.17487/RFC9256, July 2022, . Authors' Addresses Tarek Saad Cisco Systems Inc Email: tsaad.net@gmail.com Rakesh Gandhi Cisco Systems Inc Email: rgandhi@cisco.com Xufeng Liu Alef Edge Email: xufeng.liu.ietf@gmail.com Vishnu Pavan Beeram Juniper Networks Email: vbeeram@juniper.net Igor Bryskin Individual Email: i_bryskin@yahoo.com Oscar Gonzalez de Dios Telefonica Email: oscar.gonzalezdedios@telefonica.com Saad, et al. Expires 5 January 2024 [Page 99]