Network Working Group G. Lehmann Internet-Draft Telecom Sud Paris Obsoletes: 4765 (if approved) 16 April 2023 Intended status: Standards Track Expires: 18 October 2023 The Incident Detection Message Exchange Format version 2 (IDMEFv2) draft-lehmann-idmefv2-01 Abstract The Incident Detection Message Exchange Format version 2 (IDMEFv2) defines a date representation for security incidents detected on cyber and/or physical infrastructures. The format is agnostic so it can be used in standalone or combined cyber (SIEM), physical (PSIM) and availability (NMS) monitoring systems. IDMEFv2 can also be used to represent man made or natural hazards threats. IDMEFv2 improves situational awareness by facilitating correlation of multiple types of events using the same base format thus enabling efficient detection of complex and combined cyber and physical attacks and incidents. If approved this draft will obsolete RFC4765. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 18 October 2023. Lehmann Expires 18 October 2023 [Page 1] Internet-Draft IDMEFv2 April 2023 Copyright Notice Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. IDMEFv2 deployment architecture . . . . . . . . . . . . . 4 1.2. IDMEFv1 (Intrusion Detection Message Exchange Format) - RFC 4765 - Legacy . . . . . . . . . . . . . . . . . . . . . . 5 1.3. Relationship between IDMEFv2 and other event/incident formats . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1. Keywords . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2. Normative sections . . . . . . . . . . . . . . . . . . . 6 2.3. Concepts related to event processing . . . . . . . . . . 7 2.3.1. Event . . . . . . . . . . . . . . . . . . . . . . . . 7 2.3.2. Incident . . . . . . . . . . . . . . . . . . . . . . 7 2.3.3. Alert . . . . . . . . . . . . . . . . . . . . . . . . 7 2.3.4. Manager . . . . . . . . . . . . . . . . . . . . . . . 7 2.3.5. Operator . . . . . . . . . . . . . . . . . . . . . . 7 2.3.6. Analyst . . . . . . . . . . . . . . . . . . . . . . . 7 2.3.7. Attack . . . . . . . . . . . . . . . . . . . . . . . 8 2.3.8. Correlation . . . . . . . . . . . . . . . . . . . . . 8 2.3.9. Aggregation . . . . . . . . . . . . . . . . . . . . . 8 3. The IDMEF Data Types . . . . . . . . . . . . . . . . . . . . 8 3.1. Classes . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2. Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2.1. Integers . . . . . . . . . . . . . . . . . . . . . . 8 3.2.2. Floating-point values . . . . . . . . . . . . . . . . 9 3.3. Strings . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.3.1. Enumerations . . . . . . . . . . . . . . . . . . . . 9 3.3.2. Timestamps . . . . . . . . . . . . . . . . . . . . . 9 3.3.3. Geographical Locations . . . . . . . . . . . . . . . 10 3.3.4. UNECE Location Codes (UN/LOCODE) . . . . . . . . . . 10 3.3.5. Uniform Resource Identifiers (URIs) . . . . . . . . . 10 3.3.6. IP Addresses . . . . . . . . . . . . . . . . . . . . 11 3.3.7. E-mail addresses . . . . . . . . . . . . . . . . . . 11 Lehmann Expires 18 October 2023 [Page 2] Internet-Draft IDMEFv2 April 2023 3.3.8. Attachment names . . . . . . . . . . . . . . . . . . 11 3.3.9. Media types . . . . . . . . . . . . . . . . . . . . . 12 3.3.10. Universally Unique IDentifiers (UUIDs) . . . . . . . 12 3.3.11. Protocol Names . . . . . . . . . . . . . . . . . . . 12 3.3.12. IDMEF Paths . . . . . . . . . . . . . . . . . . . . . 12 3.3.13. Hashes . . . . . . . . . . . . . . . . . . . . . . . 13 3.4. Lists . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. The IDMEF extension . . . . . . . . . . . . . . . . . . . . . 14 4.1. Extending the Enumerated Values of Attributes . . . . . . 14 4.1.1. Private Extension of Enumerated Values . . . . . . . 15 4.1.2. Public Extension of Enumerated Values . . . . . . . . 15 4.2. Private Extension of Attributes . . . . . . . . . . . . . 16 5. The IDMEF Data Model . . . . . . . . . . . . . . . . . . . . 16 5.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . 16 5.2. The Alert Class . . . . . . . . . . . . . . . . . . . . . 17 5.3. The Analyzer Class . . . . . . . . . . . . . . . . . . . 32 5.4. The Sensor Class . . . . . . . . . . . . . . . . . . . . 39 5.5. The Source Class . . . . . . . . . . . . . . . . . . . . 40 5.6. The Target Class . . . . . . . . . . . . . . . . . . . . 42 5.7. The Vector Class . . . . . . . . . . . . . . . . . . . . 44 5.8. The Attachment Class . . . . . . . . . . . . . . . . . . 48 5.9. The JavaScript Object Notation Serialization Method . . . 50 5.10. Attributes completeness . . . . . . . . . . . . . . . . . 51 6. Security Considerations . . . . . . . . . . . . . . . . . . . 58 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 59 8. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 60 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 61 9.1. Normative References . . . . . . . . . . . . . . . . . . 61 9.2. Informative References . . . . . . . . . . . . . . . . . 62 Appendix A. Examples . . . . . . . . . . . . . . . . . . . . . . 63 A.1. Physical intrusion . . . . . . . . . . . . . . . . . . . 63 A.2. Cyberattack . . . . . . . . . . . . . . . . . . . . . . . 65 A.3. Server outage . . . . . . . . . . . . . . . . . . . . . . 66 A.4. Combined incident . . . . . . . . . . . . . . . . . . . . 67 Appendix B. JSON Validation Schema (Non-normative) . . . . . . . 69 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 86 1. Introduction The Incident Detection Message Exchange Format (IDMEF) is intended to solve the problem of security monitoring compartmentalization by proposing a single format to represent any type of incident, whether cyber or physical, intentional or accidental, natural or man-made. Indeed security is often associated to the Confidentiality-Integrity- Availability triad, performance and availability management systems are still run independently from security management systems. Lehmann Expires 18 October 2023 [Page 3] Internet-Draft IDMEFv2 April 2023 Additionally, with the adoption and integration of Internet of Things (IoT) and Industrial Internet of Things (IIoT) devices, and the exponential emergence of smart systems (transport, cities, buildings, etc), an increasingly interconnected mesh of cyber-physical systems (CPS) has emerged. This expansion of the attack and incident surfaces blurs the once-clear functions of cybersecurity and physical security. Finally, as IT infrastructure moves out of data centers it becomes more exposed to external threats, including natural and man-made hazards, Incident detection systems have traditionally focused on detecting cyber incidents or physical incident or availability incidents. There is an increasing need nowadays to have a unified view and management of all those incidents and their interconnection. To achieve this goal the Incident Detection Message Exchange Format offers a unique data representation for multiple types of events: * Cyber-security events (e.g. authentication failure/success, virus/ malware detection, bruteforce/scan detection, etc.) * Physical security events (e.g. intrusion detection, object detection, face or activity recognition, fire/smoke/noise/rain detection, etc.) * Availability/observability/performance events (e.g. system failure, service malfunction, performance decrease, etc.) * Natural and man made hazards events (e.g. wildfires, avalanches, droughts, earthquakes, pollution, fire, explosion, etc.) 1.1. IDMEFv2 deployment architecture IDMEFv2 can be used to exchange incident detection information between specialized managers (SIEM, PSIM, NMS) and a universal "Cyber & Physical SIEM" (CPSIEM) or directly from specialized analyzers and a CPSIEM. Lehmann Expires 18 October 2023 [Page 4] Internet-Draft IDMEFv2 April 2023 +-----------------------------+ +---------+ | "Universal" CPSIEM |<---| Hazards | +-----------------------------+ +---------+ | | | +------+ +-----+ +------+ Managers | PSIM | | NMS | | SIEM | +------+ +-----+ +------+ | | | +--------+ +----------+ +-----+ Analyzers/Sensors |Physical| |Monitoring| |Cyber| +--------+ +----------+ +-----+ | | | +-------------------------------+ | Cyber & Physical System | +-------------------------------+ Figure 1: IDMEF Use Architecture Thanks to its universality IDMEFv2 improves situational awareness by enabling correlation of multiple types of events using the same base format. This document defines a model serialization methodes for the purpose of describing and sharing these events. 1.2. IDMEFv1 (Intrusion Detection Message Exchange Format) - RFC 4765 - Legacy IDMEFv2 (Incident Detection Message Exchange Format) is based on IDMEFv1 (Intrusion Detection Message Exchange Format) concepts. But IDMEFv1 was cyber intrusion focused as IDMFv2 perimeter is much larger. Thus retro-compatibility although partly possible has not been a priority. 1.3. Relationship between IDMEFv2 and other event/incident formats IDMEFv2 focuses essentialy on high level event/incident correlation and detection.There are many standard and proprietary formats on the incident detection market and in particular on the cybersecurity market. IDMEFv2 is complementary to most of these formats. IDMEFv1 (Intrusion Detection Message Exchange Format - RFC 4765) : IDMEFv2 (Incident Detection) replaces and obsoletes IDMEFv1 (Intrusion Detection) by covering a wider spectrum. IODEFv2 (Incident Object Definition Exchange Format - RFC 5070) : IDMEFv2 helps detect incident. When an incident is detected it will be analysed and eventually fully described and shared with other Lehmann Expires 18 October 2023 [Page 5] Internet-Draft IDMEFv2 April 2023 security teams through IODEFv2. IODEFv2. IDMEF is used upstream IODEFv2. IDMEfv2 ALerts can be “attached” to IODEFv2 object to provide technical details about incidents. Syslog (System Logging) : Syslog is a loosy format with no formal structuration. Syslog can be used by sensors to send information to analyzers. Out of those multi-format syslogs the analyzer might detect an incident or an event of interest. The analyzer will then use IDMEFv2 to notify the manager which might correlate this information with other datas to confirm the incident. SNMP (Simple Network Management Protocol) : SNMP polls information from devices which is then compared to thresholds to detect incident. IDMEFv2 can be used when incident is detected downstream of SNMP to communicate the incident to the manager. IDMEFv2 can have a similar role as SNMP Traps. STIX (Structured Threat Information Expression) : is a language and serialization format used to exchange cyber threat intelligence (CTI). IDMEFv2 can help detect incidents which might lead to the creation and sharing of STIX information. Cyber analyzer can also rely on STIX information to detect incidents that will be notified in IDMEFv2 format. SIEM proprietory formats (CEF, LEEF, ECS, CIM, ...) : By covering cyber, physical and monitoring incidents type, IDMEFv2 offers a wider spectrum than those formats. Gateways between IDMEFv2 and those formats can be developped to connect legacy cyber detection systems to an IDMEFv2 architecture. 2. Terminology 2.1. Keywords The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2.2. Normative sections Implementations of IDMEFv2 are REQUIRED to fully implement: * The data types defined in Section 3 * The data model defined in Section 5 * The JavaScript Object Notation (JSON) serialization method Section 5.9. Lehmann Expires 18 October 2023 [Page 6] Internet-Draft IDMEFv2 April 2023 2.3. Concepts related to event processing 2.3.1. Event An event is something that triggered a notice. Any incident starts off as an event or a combination of events, but not all events result in an incident. An event need not be an indication of wrongdoing. E.g. someone successfully logging in or entering a building is an event. 2.3.2. Incident An incident is an event that compromises or has a significant probability of compromising at least one of the organization's security criteria such as Confidentiality, Integrity or Availability. An incident may affect a production tool, personnel, etc. It may be logical, physical or organizational in nature. Last but not least, an incident may be caused on purpose or by accident. 2.3.3. Alert An alert is a notification/message that a particular event/incident (or series of events/incidents) has occurred. 2.3.4. Manager The manager is the central console toward which all analyzers send their alerts. The manager collects, correlates, stores and display the alerts to the operators. Example : - A SIEM (Security Information & Event Management) or a Log Manager) - A PSIM (Physical Security Information Management) - A NMS (Network Management System) - A CPSIEM (Cyber & Physical Security Information Management System) 2.3.5. Operator The level 1 operator is in charge of receiving manager notifications and identify or confirm when an event should be considered as an incident. The operator must also decide if there is a know resolution for this incident or if it needs a deeper analysys. 2.3.6. Analyst The analyst will be contacted by the operator to analyze complex incidents that can’t be easily resolved. The investigation starts with the IDMEFv2 information but the analyst might need more information like raw logs for a deeper forensics. Lehmann Expires 18 October 2023 [Page 7] Internet-Draft IDMEFv2 April 2023 2.3.7. Attack An attack is an attempt to destroy, expose, alter, disable, steal or gain unauthorized access to or make unauthorized use of a cyber or physical asset. An attack is one or many kinds of incidents. 2.3.8. Correlation Correlation is the identification of relationships between two or more events. 2.3.9. Aggregation Aggregation is the consolidation of similar events into a single event. 3. The IDMEF Data Types Each object inside the IDMEF data model has an associated data type. This type may be used to validate the content of incoming IDMEF messages. 3.1. Classes The classes are meant to group related attributes together. Some of the classes may be instanciated multiple times (e.g. Source, Target, etc.) while others may only appear once in an IDMEF message (e.g. Analyzer). 3.2. Numbers 3.2.1. Integers Integers inside the IDMEF data model are expressed using the following ABNF [RFC5234] grammar: integer = *1minus int int = zero / ( digit1-9 *DIGIT ) minus = %x2D ; - zero = %0x30 ; 0 digit1-9 = %x31-39 ; 1-9 E.g. 123. Such values are indicated with the "INT" type annotation in the model. Lehmann Expires 18 October 2023 [Page 8] Internet-Draft IDMEFv2 April 2023 3.2.2. Floating-point values Floating-point values inside the IDMEF data model are expressed using the following ABNF grammar: float = integer *1frac frac = decimal-point 1*DIGIT decimal-point = %x2E ; . This grammar reuses some of the production rules listed in Section 3.2.1. E.g. 12.34. Such values are indicated with the "FLOAT" type annotation in the model. 3.3. Strings Strings are series of characters from the [UNICODE] standard and are used to represent a text. For readability, this document uses quotes (") to delimit strings, but please note that these quotes are not syntactically part of the actual strings. E.g. "Hello world". Some of the strings used in the IDMEFv2 data model follow a stricter syntax. These are included below for completeness. Such values are indicated with the "STRING" type annotation in the model. 3.3.1. Enumerations Enumerations are special strings used when valid values for an IDMEF attribute are restricted to those present in a predefined list. Such values are indicated with the "ENUM" type annotation in the model. 3.3.2. Timestamps Timestamps are used to indicate a specific moment in time. The timestamps used in the IDMEF data model follow the syntax defined by the "date-time" production rule of the grammar in [RFC3339] ch 5.6. Lehmann Expires 18 October 2023 [Page 9] Internet-Draft IDMEFv2 April 2023 E.g. "1985-04-12T23:59:59.52Z" represents a moment just before April 5th, 1985 in Coordinated Universal Time (UTC). Such values are indicated with the "TIMESTAMP" type annotation in the model. 3.3.3. Geographical Locations Some attributes inside the IDMEF data model may refer to geographical locations using a set of coordinates. The reference system for all geographical coordinates is a geographic coordinate reference system, using the World Geodetic System 1984 [WGS84]. The reference system used is the same as for the Global Positioning System (GPS). The format for such values can be either "latitude,longitude" or "latitude,longitude,altitude". Each of these coordinates is represented as a floating-point value. The latitude and longitude are expressed in degrees while the altitude is expressed in meters. E.g. "48.8584,2.2945,276.13" matches the (3-dimensional) geographical location for the top floor or the Eiffel Tower located in Paris, France, while "48.8584,2.2945" matches the same location in two dimensions (with the altitude removed). Such values are indicated with the "GEOLOC" type annotation in the model. 3.3.4. UNECE Location Codes (UN/LOCODE) Some attributes inside the IDMEF data model may refer to geographical locations using Locations Codes. These codes can be assimilated to an enumeration, where the list of possible values is defined in the United Nations Economic Commission for Europe (UNECE) Codes for Trade [UN-LOCODE]. E.g. "FR PAR" is the Location Code for the city of Paris, France. Such values are indicated with the "UNLOCODE" type annotation in the model. 3.3.5. Uniform Resource Identifiers (URIs) The IDMEF data model uses Uniform Resource Identifiers (URIs), as defined in [RFC3986], when referring to external resources. Unless otherwise specified, either a Uniform Resource Location (URL) or a Uniform Resource Name (URN) may be used where a URI is expected. Lehmann Expires 18 October 2023 [Page 10] Internet-Draft IDMEFv2 April 2023 E.g. both "https://example.com/resource" and "urn:myapp:resource" are valid Uniform Resource Identifiers. Such values are indicated with the "URI" type annotation in the model. 3.3.6. IP Addresses IP addresses inside the IDMEF data model are expressed as strings using the traditionnal dotted-decimal notation for IPv4 addresses (defined by the "dotnum" production rule in the grammar in [RFC5321]), while IPv6 addresses are expressed using the text representation defined in [RFC4291] ch 2.2. E.g. "192.0.2.1" represents a valid IPv4 address, while "::1/128" represents a valid IPv6 address. It is RECOMMENDED that implementations follow the recommendations for IPv6 text representation stated in [RFC5952]. Such values are indicated with the "IP" type annotation in the model. 3.3.7. E-mail addresses E-mail addresses inside the IDMEF data model are expressed as strings using the address specification syntax defined in [RFC5322] ch 3.4.1. E.g. "root@example.com". Such values are indicated with the "EMAIL" type annotation in the model. 3.3.8. Attachment names Attachments inside the IDMEF data model are identified using a unique name, composed of a string whose character set is limited to the ASCII letters (A-Z a-z) and digits (0-9). E.g. "state" is a valid name for an attachment. The constraint on name unicity is enforced per class. That is, but it is not possible for two attachments to share the same name inside the same alert. Such values are indicated with the "ID" type annotation in the model. Lehmann Expires 18 October 2023 [Page 11] Internet-Draft IDMEFv2 April 2023 3.3.9. Media types Media types are used in the IDMEF data model to describe an attachment's content. The syntax for such values is defined in [RFC2046]. IANA keeps a list of all currently registered media types in the Media Types registry . E.g. "application/xml" or "text/plain; charset=utf-8". Such values are indicated with the "MEDIATYPE" type annotation in the model. 3.3.10. Universally Unique IDentifiers (UUIDs) Universally Unique Identifiers (UUIDs) are used to uniquely identify IDMEF messages. It is also possible for an IDMEF message to reference other IDMEF messages using their UUIDs. The syntax for UUIDs is defined in [RFC4122]. To limit the risk of UUID collisions, implementors SHOULD NOT generate version 4 UUIDs (randomly or pseudo-randomly generated UUIDs). E.g. "ba2e4ef4-8719-42bb-a712-d6e8871c5c5a". UUIDs are case-insensitive when used in comparisons. Such values are indicated with the "UUID" type annotation in the model. 3.3.11. Protocol Names Such values are indicated with the "PROTOCOL" type annotation in the model. 3.3.12. IDMEF Paths This document defines a way to represent the path to every possible attribute inside an IDMEF message. For conciseness, the top-level "Alert" class is omitted from the path. This representation can be used in contexts where the path to an IDMEF attribute is expected. An example of such usage can be seen in the definition of the "AggrCondition" attribute inside the Alert class (Section 5.2). Lehmann Expires 18 October 2023 [Page 12] Internet-Draft IDMEFv2 April 2023 The syntax for these IDMEF paths is expressed in the following ABNF grammar: class-name = "Analyzer" / "Sensor" / "Source" / "Target" / "Vector" / "Attachment" attribute-name = 1*ALPHA class-reference = class-name "." num = *1"-" 1*DIGIT list-index = "(" num ")" path = *1class-reference attribute-name *1list-index Valid attribute names are limited to those defined for the specified class-reference (or in the top-level "Alert" class if class-reference is omitted). For example, the following path refers to the "CeaseTime" attribute of the top-level "Alert" class: "CeaseTime". Likewise, the following path refers to the "Name" attribute of the "Analyzer" class: "Analyzer.Name". For attributes defined as lists (see Section 3.4), the path may include the (0-based) index for an entry inside the list. The index defaults to 0 if omitted. This means that several (valid) representations may be used to reference the same IDMEF attribute when list attributes are involved. For example, both of the following paths refer to the IP address of the first source associated with an IDMEF message: Source.IP Source(0).IP Compatible implementations MUST reject paths that reference an unknown class, an unknown attribute, or use a list-index for an IDMEF field which is not defined as a list. A compatible implementation MUST also normalize paths before comparing them (e.g. by stripping the text "(0)" from paths referring to list attributes). 3.3.13. Hashes Hashes are sometimes used inside the data model to protect the integrity (and optionally, authenticity) of attachments. Lehmann Expires 18 October 2023 [Page 13] Internet-Draft IDMEFv2 April 2023 The syntax for these values is "function:hash_result", where "function" refers to one of the hashing function names listed in and "hash_result" contains the hexadecimal notation for the hash result obtained by calling the specified hash function on the input value. In the context of IDMEF, either a keyless or keyed hash function may be used to process the raw input value. E.g. "sha256:a02735ed8b10ad432d557bd4849c0dac3b23d64706e0618716d6df2d ef338374" Hashes are case-insensitive when used in comparisons. Such values are indicated with the "HASH" type annotation in the model. 3.4. Lists Some attributes of the IDMEF data model accept ordered lists of values. Such ordered lists are indicated with the "X[]" type annotation in the model. where "X" refers to one of the data types defined in Section 3. For example, "ENUM[]" refers to an ordered list of enumeration values. 4. The IDMEF extension In order to support the dynamic nature of security operations and to adapt to specific needs, the IDMEFv2 data model will need to continue to evolve. This section discusses how new data elements can be incorporated into the IDMEFv2. There is support to add additional enumerated values and new attributes. These extension mechanisms are designed so that adding new data elements is possible without requiring modifications to this document. Extensions can be implemented publicly or privately. With proven value, well-documented extensions can be incorporated into future versions of the specification. 4.1. Extending the Enumerated Values of Attributes Additional enumerated values can be added to select attributes either through the use of specially marked attributes with the "ext-" prefix or through a set of corresponding IANA registries. The former approach allows for the extension to remain private. The latter approach is public. Lehmann Expires 18 October 2023 [Page 14] Internet-Draft IDMEFv2 April 2023 4.1.1. Private Extension of Enumerated Values The data model supports adding new enumerated values to an attribute without public registration. For each attribute that supports this extension technique, there is a corresponding attribute in the same element whose name is identical but with a prefix of "ext-". This special attribute is referred to as the extension attribute. The attribute being extended is referred to as an extensible attribute. For example, an extensible attribute named "foo" will have a corresponding extension attribute named "ext-foo". An element may have many extensible attributes. In addition to a corresponding extension attribute, each extensible attribute has "ext-value" as one its possible enumerated values. Selection of this particular value in an extensible attribute signals that the extension attribute contains data. Otherwise, this "ext- value" value has no meaning. In order to add a new enumerated value to an extensible attribute, the value of this attribute MUST be set to "ext-value", and the new desired value MUST be set in the corresponding extension attribute. For example, extending the Category attribute of the Analyzer class would look as follows: Analyzer: { ... "Category":["ext-value"], "ext-Category": "my-new-analyzer-category", .... } A given extension attribute MUST NOT be set unless the corresponding extensible attribute has been set to "ext-value". 4.1.2. Public Extension of Enumerated Values The data model also supports publicly extending select enumerated attributes. A new entry can be added by registering a new entry in the appropriate IANA registry. Section (Table 18) provides a mapping between the extensible attributes and their corresponding registry. Lehmann Expires 18 October 2023 [Page 15] Internet-Draft IDMEFv2 April 2023 4.2. Private Extension of Attributes Use of new attributes is possible through the use of the attachment class. New attributes and their corresponding values should be stored in the Content attribute of an Attachment and the ContentEnconding must be set to JSON. For example creating a new attribute to store the email of the operator (in charge of solving the incident) will look as follows: "Attachment" : [ { "Name": "Operator", "ContentEnconding": "JSON", "Content": "{\"OperatorMail\":\"John.Does@acme.com\"}", } [ 5. The IDMEF Data Model In this section, the individual components of the IDMEF data model will be discussed in detail. For each class, the semantics will be described. 5.1. Overview +--------+ +-----+ |Analyzer|---> |Alert| +--------+ +-----+ || +------+ |Sensor| +------+ \--------\ /\ ) Vector ) / \ /--------/ / \ +------+ +------+ |Source| |Target| +------+ +------+ Figure 2: IDMEFv2 Overview Classes An IDMEF message is composed of an instance of the Alert class (Section 5.2) representing the overall properties of the message. It also contains exactly one instance of the Analyzer class (Section 5.3) and zero or more instances of the Sensor class (Section 5.4). Lehmann Expires 18 October 2023 [Page 16] Internet-Draft IDMEFv2 April 2023 The message may also describe various aspects of an event using the Source (Section 5.5), Target (Section 5.6) and Vector (Section 5.7) classes. Last but not least, it may also include zero or more instances of the Attachment class (Section 5.8), e.g. captured files or network packets related to the event for example. The relationship between the main Alert class and other classes of the data model is shown in Figure 3 (attributes are omitted for clarity). +-------+ +------------- | Alert |<>----------| Analyzer | +-------+ +------------+ | | 0..* +------------+ | |<>----------| Sensor | | | +------------+ | | 0..* +------------+ | |<>----------| Source | | | +------------+ | | 0..* +------------+ | |<>----------| Target | | | +------------+ | | 0..* +------------+ | |<>----------| Vector | | | +------------+ | | 0..* +------------+ | |<>----------| Attachment | +-------+ +------------+ Figure 3: IDMEFv2 Classes It is important to note that the data model does not specify how an alert should be categorized or identified. For example, an attacker scanning a network for machines listening on a specific port may be identified by one analyzer as a single attack against multiple targets, while another analyzer may identify it as multiple attacks from a single source. However, once an analyzer has determined the type of alert it plans on sending, the data model dictates how that alert should be formatted. 5.2. The Alert Class The Alert class contains high level information about the event that triggered the alert. Lehmann Expires 18 October 2023 [Page 17] Internet-Draft IDMEFv2 April 2023 +---------------------------+ | Alert | +---------------------------+ | STRING Version | | UUID ID | | STRING Entity | | ENUM[] Category | | STRING ext-Category | | ENUM Cause | | STRING Description | | ENUM Status | | ENUM Priority | | FLOAT Confidence | | STRING Note | | TIMESTAMP CreateTime | | TIMESTAMP StartTime | | TIMESTAMP EndTime | | STRING[] AltNames | | STRING[] AltCategory | | URI[] Ref | | UUID[] CorrelID | | CONDITION[] AggrCondition | | UUID[] PredID | | UUID[] RelID | +---------------------------+ Figure 4: The Alert class The aggregate classes that make up Alert are: Analyzer Exactly one. An instance of the Analyzer class (Section 5.3) that describes the tool/device responsible for the analysis that resulted in the alert being created and sent. Sensor Zero or more. Instances of the Sensor class (Section 5.4) used to describe the sensor(s) that captured the information used during the analysis. Depending on the tools/devices used to detect incidents, an Analyzer may rely on the output from a single sensor or from multiple sensors to generate alerts. In addition, the Analyzer and Sensor may actually be part of the same physical device and may share some of their attributes (e.g. IP, Hostname, Model, etc.). Source Lehmann Expires 18 October 2023 [Page 18] Internet-Draft IDMEFv2 April 2023 Zero or more. Instances of the Source class (Section 5.5) used to describe the source(s) of the incident (e.g. attackers, faulty device, etc.). Target Zero or more. Instances of the Target class (Section 5.6) used to describe the target(s) of the incident, i.e. the impacted devices/users/services/locations. Vector Zero or more. Instances of the Vector class (Section 5.7) used to describe the means which were employed by the sources to disrupt the targets. E.g. to describe a drone crashing into a building and resulting in service loss or a malware email delivered opened in a mailbox and resulting in service loss. Attachment Zero or more. Instances of the Attachment class (Section 5.8) used to describe the electronic artifacts captured in relation with the event. The intent of the Attachment class is to keep track of the electronic files left as a trail during the event. This may include things like on-disk files (e.g. malware samples), network packet captures, videos or still images from a camera feed, voice recording, etc. The Alert class has the following attributes: Version Mandatory. The version of the IDMEF format in use by this alert. During the drafts tuning period the version is equal to the draft version. Therefore it is "2.D.V01" for Draft V01. ID Mandatory. Unique identifier for the alert. Entity Optional. Tenant ID to support multi-tenancy (e.g. decentralized infrastructure, local agency, subsidiary company, etc.). Should be used when there are multiple sites/locations or multiple tenants (e.g. by Managed Security Services Providers). Category Lehmann Expires 18 October 2023 [Page 19] Internet-Draft IDMEFv2 April 2023 Optional. The incident's category & subcategory as listed in [ENISA-RIST] using the format "category.subcategory" (e.g. "Attempt.Exploit"). +======+===========================+=============================+ | Rank | Keyword | Description | +======+===========================+=============================+ | 0 | Abusive.Spam | Or 'Unsolicited Bulk | | | | Email', this means that | | | | the recipient has not | | | | granted verifiable | | | | permission for the message | | | | to be sent and that the | | | | message is sent as part of | | | | a larger collection of | | | | messages, all having a | | | | functionally comparable | | | | content. This IOC refers | | | | to resources, which make | | | | up a SPAM infrastructure, | | | | be it a harvesters like | | | | address verification, URLs | | | | in spam e-mails etc. | +------+---------------------------+-----------------------------+ | 1 | Abusive.Harassment | Discretization or | | | | discrimination of | | | | somebody, e.g. cyber | | | | stalking, racism or | | | | threats against one or | | | | more individuals. | +------+---------------------------+-----------------------------+ | 2 | Abusive.Illicit | Child Sexual Exploitation | | | | (CSE), Sexual content, | | | | glorification of violence, | | | | etc. | +------+---------------------------+-----------------------------+ | 3 | Malicious.System | System infected with | | | | malware, e.g. PC, | | | | smartphone or server | | | | infected with a rootkit. | | | | Most often this refers to | | | | a connection to a | | | | sinkholed C2 server | +------+---------------------------+-----------------------------+ | 4 | Malicious.Botnet | Command-and-control server | | | | contacted by malware on | | | | infected systems. | +------+---------------------------+-----------------------------+ Lehmann Expires 18 October 2023 [Page 20] Internet-Draft IDMEFv2 April 2023 | 5 | Malicious.Distribution | URI used for malware | | | | distribution, e.g. a | | | | download URL included in | | | | fake invoice malware spam | | | | or exploit-kits (on | | | | websites). | +------+---------------------------+-----------------------------+ | 6 | Malicious.Configuration | URI hosting a malware | | | | configuration file, e.g. | | | | web-injects for a banking | | | | trojan. | +------+---------------------------+-----------------------------+ | 7 | Recon.Scanning | Attacks that send requests | | | | to a system to discover | | | | weaknesses. This also | | | | includes testing processes | | | | to gather information on | | | | hosts, services and | | | | accounts. Examples: | | | | fingerd, DNS querying, | | | | ICMP, SMTP (EXPN, RCPT, | | | | ...), port scanning. | +------+---------------------------+-----------------------------+ | 8 | Recon.Sniffing | Observing and recording of | | | | network traffic | | | | (wiretapping). | +------+---------------------------+-----------------------------+ | 9 | Recon.SocialEngineering | Gathering information from | | | | a human being in a non- | | | | technical way (e.g. lies, | | | | tricks, bribes, or | | | | threats). | +------+---------------------------+-----------------------------+ | 10 | Attempt.Exploit | An attempt to compromise a | | | | system or to disrupt any | | | | service by exploiting | | | | vulnerabilities with a | | | | standardised identifier | | | | such as CVE name (e.g. | | | | buffer overflow, backdoor, | | | | cross site scripting, | | | | etc.) | +------+---------------------------+-----------------------------+ | 11 | Attempt.Login | Multiple login attempts | | | | (Guessing / cracking of | | | | passwords, brute force). | | | | This IOC refers to a | | | | resource, which has been | Lehmann Expires 18 October 2023 [Page 21] Internet-Draft IDMEFv2 April 2023 | | | observed to perform brute- | | | | force attacks over a given | | | | application protocol. | +------+---------------------------+-----------------------------+ | 12 | Attempt.NewSignature | An attack using an unknown | | | | exploit. | +------+---------------------------+-----------------------------+ | 13 | Intrusion.AdminCompromise | Compromise of a system | | | | where the attacker gained | | | | administrative privileges. | +------+---------------------------+-----------------------------+ | 14 | Intrusion.UserCompromise | Compromise of a system | | | | using an unprivileged | | | | (user/service) account. | +------+---------------------------+-----------------------------+ | 15 | Intrusion.AppCompromise | Compromise of an | | | | application by exploiting | | | | (un-)known software | | | | vulnerabilities, e.g. SQL | | | | injection. | +------+---------------------------+-----------------------------+ | 16 | Intrusion.SysCompromise | Compromise of a system, | | | | e.g. unauthorised logins | | | | or commands. This | | | | includes compromising | | | | attempts on honeypot | | | | systems. | +------+---------------------------+-----------------------------+ | 17 | Intrusion.Burglary | Physical intrusion, e.g. | | | | into corporate building or | | | | data-centre. | +------+---------------------------+-----------------------------+ | 18 | Availability.DoS | Denial of Service attack, | | | | e.g. sending specially | | | | crafted requests to a web | | | | application which causes | | | | the application to crash | | | | or slow down. | +------+---------------------------+-----------------------------+ | 19 | Availability.DDoS | Distributed Denial of | | | | Service attack, e.g. SYN- | | | | Flood or UDP-based | | | | reflection/amplification | | | | attacks. | +------+---------------------------+-----------------------------+ | 20 | Availability.Misconf | Software misconfiguration | | | | resulting in service | | | | availability issues, e.g. | Lehmann Expires 18 October 2023 [Page 22] Internet-Draft IDMEFv2 April 2023 | | | DNS server with outdated | | | | DNSSEC Root Zone KSK. | +------+---------------------------+-----------------------------+ | 21 | Availability.Theft | Physical theft, e.g. | | | | stolen laptop computer, | | | | stolen USB key, stolen | | | | paper document, etc. | +------+---------------------------+-----------------------------+ | 22 | Availability.Sabotage | Physical sabotage, e.g | | | | cutting wires or malicious | | | | arson. | +------+---------------------------+-----------------------------+ | 23 | Availability.Outage | Outage caused e.g. by air | | | | condition failure or | | | | natural disaster. | +------+---------------------------+-----------------------------+ | 24 | Availability.Failure | Failure, malfunction (e.g. | | | | : bug, wear, faults, etc.) | +------+---------------------------+-----------------------------+ | 25 | Information. | Unauthorised access to | | | UnauthorizedAccess | information, e.g. by | | | | abusing stolen login | | | | credentials for a system | | | | or application, | | | | intercepting traffic or | | | | gaining access to physical | | | | documents. | +------+---------------------------+-----------------------------+ | 26 | Information. | Unauthorised modification | | | UnauthorizedModification | of information, e.g. by an | | | | attacker abusing stolen | | | | login credentials for a | | | | system or application or a | | | | ransomware encrypting | | | | data. Also includes | | | | defacements. | +------+---------------------------+-----------------------------+ | 27 | Information.DataLoss | Loss of data, e.g. caused | | | | by harddisk failure or | | | | physical theft. | +------+---------------------------+-----------------------------+ | 28 | Information.DataLeak | Leaked confidential | | | | information like | | | | credentials or personal | | | | data. | +------+---------------------------+-----------------------------+ | 29 | Fraud.UnauthorizedUsage | Using resources for | | | | unauthorised purposes | Lehmann Expires 18 October 2023 [Page 23] Internet-Draft IDMEFv2 April 2023 | | | including profit-making | | | | ventures, e.g. the use of | | | | e-mail to participate in | | | | illegal profit chain | | | | letters or pyramid | | | | schemes. | +------+---------------------------+-----------------------------+ | 30 | Fraud.Copyright | Offering or Installing | | | | copies of unlicensed | | | | commercial software or | | | | other copyright protected | | | | materials (Warez). | +------+---------------------------+-----------------------------+ | 31 | Fraud.Masquerade | Type of attack in which | | | | one entity illegitimately | | | | impersonates the identity | | | | of another in order to | | | | benefit from it. | +------+---------------------------+-----------------------------+ | 32 | Fraud.Phishing | Masquerading as another | | | | entity in order to | | | | persuade the user to | | | | reveal private | | | | credentials. This IOC | | | | most often refers to a | | | | URL, which is used to | | | | phish user credentials. | +------+---------------------------+-----------------------------+ | 33 | Vulnerable.Crypto | Publicly accessible | | | | services offering weak | | | | crypto, e.g. web servers | | | | susceptible to POODLE/ | | | | FREAK attacks. | +------+---------------------------+-----------------------------+ | 34 | Vulnerable.DDoS | Publicly accessible | | | | services that can be | | | | abused for conducting DDoS | | | | reflection/amplification | | | | attacks, e.g. DNS open- | | | | resolvers or NTP servers | | | | with monlist enabled. | +------+---------------------------+-----------------------------+ | 35 | Vulnerable.Surface | Potentially unwanted | | | | publicly accessible | | | | services, e.g. Telnet, | | | | RDP or VNC. | +------+---------------------------+-----------------------------+ | 36 | Vulnerable.Disclosure | Publicly accessible | Lehmann Expires 18 October 2023 [Page 24] Internet-Draft IDMEFv2 April 2023 | | | services potentially | | | | disclosing sensitive | | | | information, e.g. SNMP or | | | | Redis. | +------+---------------------------+-----------------------------+ | 37 | Vulnerable.System | A system which is | | | | vulnerable to certain | | | | attacks. Example: | | | | misconfigured client proxy | | | | settings (example: WPAD), | | | | outdated operating system | | | | version, XSS | | | | vulnerabilities, etc. | +------+---------------------------+-----------------------------+ | 38 | Geophysical.Earthquake | A hazard originating from | | | | solid earth. This term is | | | | used interchangeably with | | | | the term geological | | | | hazard. | +------+---------------------------+-----------------------------+ | 39 | Geophysical.MassMovement | A hazard originating from | | | | solid earth. This term is | | | | used interchangeably with | | | | the term geological | | | | hazard. | +------+---------------------------+-----------------------------+ | 40 | Geophysical.Volcanic | A hazard originating from | | | | solid earth. This term is | | | | used interchangeably with | | | | the term geological | | | | hazard. | +------+---------------------------+-----------------------------+ | 41 | Meteorological. | A hazard caused by short- | | | Temperature | lived, micro- to meso- | | | | scale extreme weather and | | | | atmospheric conditions | | | | that last from minutes to | | | | days. | +------+---------------------------+-----------------------------+ | 42 | Meteorological.Fog | A hazard caused by short- | | | | lived, micro- to meso- | | | | scale extreme weather and | | | | atmospheric conditions | | | | that last from minutes to | | | | days. | +------+---------------------------+-----------------------------+ | 43 | Meteorological.Storm | A hazard caused by short- | | | | lived, micro- to meso- | Lehmann Expires 18 October 2023 [Page 25] Internet-Draft IDMEFv2 April 2023 | | | scale extreme weather and | | | | atmospheric conditions | | | | that last from minutes to | | | | days. | +------+---------------------------+-----------------------------+ | 44 | Hydrological.Flood | A hazard caused by the | | | | occurrence, movement, and | | | | distribution of surface | | | | and subsurface freshwater | | | | and saltwater. | +------+---------------------------+-----------------------------+ | 45 | Hydrological.Landslide | A hazard caused by the | | | | occurrence, movement, and | | | | distribution of surface | | | | and subsurface freshwater | | | | and saltwater. | +------+---------------------------+-----------------------------+ | 46 | Hydrological.Wave | A hazard caused by the | | | | occurrence, movement, and | | | | distribution of surface | | | | and subsurface freshwater | | | | and saltwater. | +------+---------------------------+-----------------------------+ | 47 | Climatological.Drought | A hazard caused by long- | | | | lived, meso- to macro- | | | | scale atmospheric | | | | processes ranging from | | | | intra-seasonal to multi- | | | | decadal climate | | | | variability. | +------+---------------------------+-----------------------------+ | 48 | Climatological. | A hazard caused by long- | | | LakeOutburst | lived, meso- to macro- | | | | scale atmospheric | | | | processes ranging from | | | | intra-seasonal to multi- | | | | decadal climate | | | | variability. | +------+---------------------------+-----------------------------+ | 49 | Climatological.Wildfire | A hazard caused by long- | | | | lived, meso- to macro- | | | | scale atmospheric | | | | processes ranging from | | | | intra-seasonal to multi- | | | | decadal climate | | | | variability. | +------+---------------------------+-----------------------------+ | 50 | Biological.Epidemic | A hazard caused by the | Lehmann Expires 18 October 2023 [Page 26] Internet-Draft IDMEFv2 April 2023 | | | exposure to living | | | | organisms and their toxic | | | | substances (e.g. venom, | | | | mold) or vector-borne | | | | diseases that they may | | | | carry. Examples are | | | | venomous wildlife and | | | | insects, poisonous plants, | | | | and mosquitoes carrying | | | | disease-causing agents | | | | such as parasites, | | | | bacteria, or viruses (e.g. | | | | malaria). | +------+---------------------------+-----------------------------+ | 51 | Biological.Insect | A hazard caused by the | | | | exposure to living | | | | organisms and their toxic | | | | substances (e.g. venom, | | | | mold) or vector-borne | | | | diseases that they may | | | | carry. Examples are | | | | venomous wildlife and | | | | insects, poisonous plants, | | | | and mosquitoes carrying | | | | disease-causing agents | | | | such as parasites, | | | | bacteria, or viruses (e.g. | | | | malaria). | +------+---------------------------+-----------------------------+ | 52 | Biological.Animal | A hazard caused by the | | | | exposure to living | | | | organisms and their toxic | | | | substances (e.g. venom, | | | | mold) or vector-borne | | | | diseases that they may | | | | carry. Examples are | | | | venomous wildlife and | | | | insects, poisonous plants, | | | | and mosquitoes carrying | | | | disease-causing agents | | | | such as parasites, | | | | bacteria, or viruses (e.g. | | | | malaria). | +------+---------------------------+-----------------------------+ | 53 | Extraterrestrial.Impact | A hazard caused by | | | | asteroids, meteoroids, and | | | | comets as they pass near- | | | | earth, enter the Earth’s | Lehmann Expires 18 October 2023 [Page 27] Internet-Draft IDMEFv2 April 2023 | | | atmosphere, and/or strike | | | | the Earth, and by changes | | | | in interplanetary | | | | conditions that effect the | | | | Earth’s magnetosphere, | | | | ionosphere, and | | | | thermosphere. | +------+---------------------------+-----------------------------+ | 54 | Extraterrestrial. | A hazard caused by | | | SpaceWeather | asteroids, meteoroids, and | | | | comets as they pass near- | | | | earth, enter the Earth’s | | | | atmosphere, and/or strike | | | | the Earth, and by changes | | | | in interplanetary | | | | conditions that effect the | | | | Earth’s magnetosphere, | | | | ionosphere, and | | | | thermosphere. | +------+---------------------------+-----------------------------+ | 55 | Other.Uncategorised | All incidents which don't | | | | fit in one of the given | | | | categories should be put | | | | into this class or the | | | | incident is not | | | | categorised. | +------+---------------------------+-----------------------------+ | 56 | Other.Undetermined | The categorisation of the | | | | incident is unknown/ | | | | undetermined. | +------+---------------------------+-----------------------------+ | 57 | Test.Test | Meant for testing. | +------+---------------------------+-----------------------------+ | 58 | ext-value | A value used to indicate | | | | that this attribute is | | | | extended and the actual | | | | value is provided using | | | | the corresponding ext-* | | | | attribute. (see | | | | Section 4.1.1) | +------+---------------------------+-----------------------------+ Table 1: Incident taxonomy ext-Category Optional. A means by which to extend the Category attribute. (see Section 4.1.1) Lehmann Expires 18 October 2023 [Page 28] Internet-Draft IDMEFv2 April 2023 Cause Optional. Alert cause. The cause can be modified by any analyser on the way of the alert and later by the operator and/or the analyst if new investigation reveals and confirms a different cause of the event. +======+=============+=========================================+ | Rank | Keyword | Description | +======+=============+=========================================+ | 0 | Normal | The event is related to an expected | | | | phenomenon or to a phenomenon that does | | | | not qualify as out of the ordinary. | +------+-------------+-----------------------------------------+ | 1 | Error | The event is related to a human error. | +------+-------------+-----------------------------------------+ | 2 | Malicious | The event is related to malicious code | | | | or malicious actions. | +------+-------------+-----------------------------------------+ | 3 | Malfunction | The event is related to a device or | | | | service malfunction. | +------+-------------+-----------------------------------------+ | 4 | Hazard | The event is related to a hazard | | | | phenomenon. | +------+-------------+-----------------------------------------+ | 5 | Unknown | The cause of the event is unknown. | +------+-------------+-----------------------------------------+ Table 2: Incident causes Description Optional. Short free text human-readable description of the event. The description can add detail to the alert classification for easiest/faster comprehension by the operator. Example : * Cryptoware WannaCry blocked on pegasus server * Unknown person entering through east doorway Status Optional. Event state in the overall event lifecycle. Lehmann Expires 18 October 2023 [Page 29] Internet-Draft IDMEFv2 April 2023 +======+==========+===========================================+ | Rank | Keyword | Description | +======+==========+===========================================+ | 0 | Event | The event is still considered as an | | | | harmless event and should not be treated. | +------+----------+-------------------------------------------+ | 1 | Incident | The event is considered as an incident | | | | and should be taken care of. | +------+----------+-------------------------------------------+ Table 3: Incident statuses Priority Optional. Priority of the alert. Priority is defined by conbining impact and urgency. It indicates how fast the incident should be taken care of. Impact defines the enormity of the situation and mostly deals with “How Many” or “how much” question. It can be in terms of people, finances, systems, etc. How many people and/or systems impacted, how badly are they impacted (is there potential physical impact ?) , how much financial loss, severity of legal liabilities,... Impact could be considered equivalent to "Severity". Urgency is associated with time. The time it takes to have the perceived Impact. For example, a high impact incident may have low urgency if the impact will not affect the business until the end of the financial year. +======+=========+=========================================+ | Rank | Keyword | Description | +======+=========+=========================================+ | 0 | Unknown | Priority unknow | +------+---------+-----------------------------------------+ | 1 | Info | No priority, the alert is informational | +------+---------+-----------------------------------------+ | 2 | Low | Low priority | +------+---------+-----------------------------------------+ | 3 | Medium | Medium priority | +------+---------+-----------------------------------------+ | 4 | High | High priority | +------+---------+-----------------------------------------+ Table 4: Incident severities Confidence Optional. A floating-point value between 0 and 1 indicating the analyzer's confidence in its own reliability of this particular detection, where 0 means that the detection is surely incorrect while 1 means there is no doubt about the detection made. Lehmann Expires 18 October 2023 [Page 30] Internet-Draft IDMEFv2 April 2023 Note Optional. Free text human-readable additional note, possibly a longer description of the incident if is not already obvious. The Note attribute can be used to store any additional information. It can be additional information about the event and/or about the incident resolution, although the incident resolution information should in principle be stored elsewhere (with a link with the external tool in AltNames) CreateTime Mandatory. Timestamp indicating when the message was created. StartTime Optional. Timestamp indicating the deduced start of the event. StartTime can be later than CreateTime in case or Alerts created from forecast information (e.g. Snow Storm in two days staring at 10h00) EndTime Optional. Timestamp indicating the deduced end of the event. AltNames Optional. Alternative identifiers; strings which help pair the event to internal systems' information (for example ticket IDs inside a request tracking systems). AltCategory Optional. Alternate categories from a reference other than [ENISA-RIST] (e.g. MISP, MITRE ATT@CK or another proprietary/ internal reference). Ref Optional. References to sources of information related to the alert and/or vulnerability, and specific to this alert. This MAY be a URL to additional info, or a URN in a registered or unregistered ad-hoc namespace bearing reasonable information value and uniqueness, such as "urn:cve:CVE-2013-2266". CorrelID Optional. Identifiers for the messages which were used as information sources to create this message, in case the message has been created based on correlation/analysis/deduction from other messages. AggrCondition Lehmann Expires 18 October 2023 [Page 31] Internet-Draft IDMEFv2 April 2023 Optional. A list of IDMEF fields used to aggregate events. The values for these fields will be the same in all aggregated events. This attribute should mostly be set by intermediary nodes, which detect duplicates, or aggregate events, spanning multiple detection windows, into a longer one. The "StartTime" and "EndTime" attributes are used in conjunction with this attribute to describe the aggregation window. PredID Optional. A list containing the identifiers of previous messages which are obsoleted by this message. The obsoleted alerts SHOULD NOT be used anymore. This field can be used to "update" an alert. RelID Optional. A list containing the identifiers of other messages related to this message. 5.3. The Analyzer Class The Analyzer class describes the module that has analyzed the data captured by the sensors, identified an event of interest and decided to create an alert. +-----------------------+ | Analyzer | +-----------------------+ | IP IP | | STRING Name | | STRING Hostname | | STRING Model | | ENUM[] Type | | ENUM[] Category | | STRING ext-Category | | ENUM[] Data | | STRING ext-Data | | ENUM[] Method | | STRING ext-Method | | GEOLOC GeoLocation | | UNLOCODE UnLocation | | STRING Location | +-----------------------+ Figure 5: The Analyzer class Lehmann Expires 18 October 2023 [Page 32] Internet-Draft IDMEFv2 April 2023 The Analyzer class has the following attributes: IP Mandatory. Analyzer IP address. Name Mandatory. Name of the analyzer, which must be reasonably unique, however still bear some meaningful sense. This attribute usually denotes the hierarchy of organizational units the detector belongs to and its own name. It MAY also be used to distinguish multiple analyzers running with the same IP address. Hostname Optional. Hostname of this analyzer. SHOULD be a fully-qualified domain name. Model Optional. Analyzer model description (usually its generic name, brand and version). Type Optional. Analyzer type. +======+==============+======================================+ | Rank | Keyword | Description | +======+==============+======================================+ | 0 | Cyber | The analyzer specializes in the | | | | detection of cyber incidents | +------+--------------+--------------------------------------+ | 1 | Physical | The analyzer specializes in the | | | | detection of physical incidents | +------+--------------+--------------------------------------+ | 2 | Availability | The analyzer specializes in the | | | | detection of availability incidents | +------+--------------+--------------------------------------+ | 3 | Combined | The analyzer specilizes in | | | | detections that combine data from | | | | multiple domains (e.g. a combination | | | | of Cyber and Availability data) | +------+--------------+--------------------------------------+ Table 5: Analyzer types Category Optional. Analyzer categories. Lehmann Expires 18 October 2023 [Page 33] Internet-Draft IDMEFv2 April 2023 +======+===========+===========================================+ | Rank | Keyword | Description | +======+===========+===========================================+ | 0 | 1DLiS | 1D LIDAR Sensor | +------+-----------+-------------------------------------------+ | 1 | 2DLiS | 2D LIDAR Sensor | +------+-----------+-------------------------------------------+ | 2 | 3DLiS | 3D LIDAR Sensor | +------+-----------+-------------------------------------------+ | 3 | 1DLaS | 1D Laser Sensor | +------+-----------+-------------------------------------------+ | 4 | 2DLaS | 2D Laser Sensor | +------+-----------+-------------------------------------------+ | 5 | 3DLaS | 3D Laser Sensor | +------+-----------+-------------------------------------------+ | 6 | VAD | Voice Activity Detection | +------+-----------+-------------------------------------------+ | 7 | HAR | Human Activity Detection | +------+-----------+-------------------------------------------+ | 8 | FRC | Face Recognition Camera | +------+-----------+-------------------------------------------+ | 9 | VNIR | Visible and Near-InfraRed | +------+-----------+-------------------------------------------+ | 10 | SWIR | Short Wavelength InfraRed | +------+-----------+-------------------------------------------+ | 11 | MWIR | Middle Wavelength InfraRed | +------+-----------+-------------------------------------------+ | 12 | LWIR | Long Wavelength InfraRed | +------+-----------+-------------------------------------------+ | 13 | ADS | Anti-Drone System | +------+-----------+-------------------------------------------+ | 14 | ODC | Object Detection Camera | +------+-----------+-------------------------------------------+ | 15 | DDOS | Anti-DDoS (Distributed Denial of Service) | | | | protection | +------+-----------+-------------------------------------------+ | 16 | SPAM | Spam detection, phishing detection, etc. | +------+-----------+-------------------------------------------+ | 17 | AV | Signature-based virus/malware detection | +------+-----------+-------------------------------------------+ | 18 | EDR | Endpoint Detection and Response | +------+-----------+-------------------------------------------+ | 19 | FW | Firewall | +------+-----------+-------------------------------------------+ | 20 | NIDS | Network Intrusion Detection System | +------+-----------+-------------------------------------------+ | 21 | HIDS | Host Intrusion Detection System | +------+-----------+-------------------------------------------+ Lehmann Expires 18 October 2023 [Page 34] Internet-Draft IDMEFv2 April 2023 | 22 | WIDS | Wi-Fi Intrusion Detection System | +------+-----------+-------------------------------------------+ | 23 | PROX | Proxy, e.g. detection of violations to | | | | the company's security policy | +------+-----------+-------------------------------------------+ | 24 | WAF | Web Application Firewall | +------+-----------+-------------------------------------------+ | 25 | HPT | Honeypot | +------+-----------+-------------------------------------------+ | 26 | LOG | Log analyzer | +------+-----------+-------------------------------------------+ | 27 | IAM | Identity and Access Management tool | +------+-----------+-------------------------------------------+ | 28 | VPN | Devices/tools related to Virtual Private | | | | Network | +------+-----------+-------------------------------------------+ | 29 | ETL | Extract-Transform-Load tools | +------+-----------+-------------------------------------------+ | 30 | RASP | Runtime Application Self-Protection | +------+-----------+-------------------------------------------+ | 31 | BAST | Clientless Remote Desktop Gateway / | | | | administration bastions | +------+-----------+-------------------------------------------+ | 32 | NAC | Devices/tools related to Network Access | | | | Control | +------+-----------+-------------------------------------------+ | 33 | SIEM | Security Information and Event Management | | | | systems | +------+-----------+-------------------------------------------+ | 34 | NMS | Network Management Systems | +------+-----------+-------------------------------------------+ | 35 | ext-value | A value used to indicate that this | | | | attribute is extended and the actual | | | | value is provided using the corresponding | | | | ext-* attribute. (see Section 4.1.1) | +------+-----------+-------------------------------------------+ Table 6: Analyzer categories ext-Category Optional. A means by which to extend the Category attribute. (see Section 4.1.1) Data Optional. Type of data analyzed during the detection. Lehmann Expires 18 October 2023 [Page 35] Internet-Draft IDMEFv2 April 2023 +======+===============+================================+ | Rank | Keyword | Description | +======+===============+================================+ | 0 | Light | | +------+---------------+--------------------------------+ | 1 | Noise | | +------+---------------+--------------------------------+ | 2 | Touch | | +------+---------------+--------------------------------+ | 3 | Images | | +------+---------------+--------------------------------+ | 4 | Vibrations | | +------+---------------+--------------------------------+ | 5 | Lidar | | +------+---------------+--------------------------------+ | 6 | Thermic | | +------+---------------+--------------------------------+ | 7 | Seismic | | +------+---------------+--------------------------------+ | 8 | Temperature | | +------+---------------+--------------------------------+ | 9 | Rain | | +------+---------------+--------------------------------+ | 10 | Water | | +------+---------------+--------------------------------+ | 11 | Humidity | | +------+---------------+--------------------------------+ | 12 | Particles | | +------+---------------+--------------------------------+ | 13 | Contact | | +------+---------------+--------------------------------+ | 14 | MagneticField | | +------+---------------+--------------------------------+ | 15 | Acoustics | | +------+---------------+--------------------------------+ | 16 | Fog | | +------+---------------+--------------------------------+ | 17 | External | | +------+---------------+--------------------------------+ | 18 | Reporting | | +------+---------------+--------------------------------+ | 19 | Connection | | +------+---------------+--------------------------------+ | 20 | Datagram | | +------+---------------+--------------------------------+ | 21 | Content | | +------+---------------+--------------------------------+ | 22 | Data | | Lehmann Expires 18 October 2023 [Page 36] Internet-Draft IDMEFv2 April 2023 +------+---------------+--------------------------------+ | 23 | File | | +------+---------------+--------------------------------+ | 24 | Flow | | +------+---------------+--------------------------------+ | 25 | Log | | +------+---------------+--------------------------------+ | 26 | Protocol | | +------+---------------+--------------------------------+ | 27 | Host | | +------+---------------+--------------------------------+ | 28 | Network | | +------+---------------+--------------------------------+ | 29 | Alert | | +------+---------------+--------------------------------+ | 30 | Relay | | +------+---------------+--------------------------------+ | 31 | Auth | | +------+---------------+--------------------------------+ | 32 | SNMP | | +------+---------------+--------------------------------+ | 33 | ext-value | A value used to indicate that | | | | this attribute is extended and | | | | the actual value is provided | | | | using the corresponding ext-* | | | | attribute. (see Section 4.1.1) | +------+---------------+--------------------------------+ Table 7: Analyzer data ext-Data Optional. A means by which to extend the Data attribute. (see Section 4.1.1) Method Optional. Detection method. Lehmann Expires 18 October 2023 [Page 37] Internet-Draft IDMEFv2 April 2023 +======+=============+===========================================+ | Rank | Keyword | Description | +======+=============+===========================================+ | 0 | Biometric | | +------+-------------+-------------------------------------------+ | 1 | Policy | | +------+-------------+-------------------------------------------+ | 2 | Heat | | +------+-------------+-------------------------------------------+ | 3 | Movement | | +------+-------------+-------------------------------------------+ | 4 | Blackhole | | +------+-------------+-------------------------------------------+ | 5 | Signature | | +------+-------------+-------------------------------------------+ | 6 | Statistical | | +------+-------------+-------------------------------------------+ | 7 | Heuristic | | +------+-------------+-------------------------------------------+ | 8 | Integrity | | +------+-------------+-------------------------------------------+ | 9 | Honeypot | | +------+-------------+-------------------------------------------+ | 10 | Tarpit | | +------+-------------+-------------------------------------------+ | 11 | Recon | | +------+-------------+-------------------------------------------+ | 12 | Correlation | | +------+-------------+-------------------------------------------+ | 13 | Monitor | | +------+-------------+-------------------------------------------+ | 14 | AI | | +------+-------------+-------------------------------------------+ | 15 | Threshold | | +------+-------------+-------------------------------------------+ | 16 | ext-value | A value used to indicate that | | | | this attribute is extended and | | | | the actual value is provided | | | | using the corresponding ext-* | | | | attribute. (see Section 4.1.1) | +------+-------------+-------------------------------------------+ Table 8: Analyzer methods ext-Method Optional. A means by which to extend the Method attribute. (see Section 4.1.1) Lehmann Expires 18 October 2023 [Page 38] Internet-Draft IDMEFv2 April 2023 GeoLocation Optional. GPS coordinates for the analyzer. UnLocation Optional. Standard UN/Locode for the analyzer. Location Optional. Internal name for the location of the analyzer. 5.4. The Sensor Class The Sensor class describes the module that captured the data before sending it to an analyzer. The Sensor may be a subpart of the Analyzer. +----------------------+ | Sensor | +----------------------+ | IP IP | | STRING Name | | STRING Hostname | | STRING Model | | GEOLOC GeoLocation | | UNLOCODE UnLocation | | STRING Location | | STRING CaptureZone | +----------------------+ Figure 6: The Sensor class The Sensor class has the following attributes: IP Mandatory. The sensor's IP address. Name Mandatory. Name of the sensor, which must be reasonably unique, however still bear some meaningful sense. This attribute usually denotes the hierarchy of organizational units the sensor belongs to and its own name. It MAY also be used to distinguish multiple sensors running with the same IP address. Hostname Optional. The sensor's hostname. Lehmann Expires 18 October 2023 [Page 39] Internet-Draft IDMEFv2 April 2023 This SHOULD be a fully qualified domain name, but may not conform exactly because values extracted from logs, messages, DNS, etc. may themselves be malformed. An empty string MAY be used to explicitly state that this value was inquired but not found (missing DNS entry). Model Optional. The sensor model's description (usually its generic name, brand and version). GeoLocation Optional. GPS coordinates for the analyzerr. UnLocation Optional. Standard UN/Locode for the sensor. Location Optional. Internal name for the location of the sensor. CaptureZone Optional. A string that describes the "capture zone" of the sensor, as a JSON-serialized string. Depending on the type of sensor, the capture zone may for instance refer to: * A JSON object describing a camera's settings (elevation, horizontal and vertical field of view, azimuth, etc.) * A description of the IP network where packet capture is taking place. 5.5. The Source Class The Source class describes the origin(s) of the event(s) leading up to the alert. Lehmann Expires 18 October 2023 [Page 40] Internet-Draft IDMEFv2 April 2023 +------------------------+ | Source | +------------------------+ | IP IP | | STRING Hostname | | STRING Note | | STRING[] TI | | STRING User | | EMAIL Email | | PROTOCOL[] Protocol | | INT[] Port | | GEOLOC GeoLocation | | UNLOCODE UnLocation | | STRING Location | | ID[] Attachment | +------------------------+ Figure 7: The Source class The Source class has the following attributes: IP Optional. Source IP address. Hostname Optional. Hostname of this source. This SHOULD be a fully qualified domain name, but may not conform exactly because values extracted from logs, messages, DNS, etc. may themselves be malformed. An empty string MAY be used to explicitly state that this value was inquired but not found (missing DNS entry). Note Optional. Free text human-readable additional note for this source. TI Optional. Threat Intelligence data about the source. Values in this list MUST use the format "attribute:origin", where "attribute" refers to the attribute inside this source found inside a Threat Intelligence database, and "origin" contains a short identifier for the Threat Intelligence database. E.g. "IP:Dshield". Lehmann Expires 18 October 2023 [Page 41] Internet-Draft IDMEFv2 April 2023 Please note that the same attribute may appear multiple times inside the list (because a match was found in multiple Threat Intelligence databases). User Optional. User ID or login responsible for the alert. Email Optional. Email address responsible for the alert. E.g. the value of the "Reply-To" or "From" header inside a phishing e-mail. Protocol Optional. Protocols related to connections from/to this source. If several protocols are stacked, they MUST be ordered from the lowest (the closest to the medium) to the highest (the closest to the application) according to the ISO/OSI model. Port Optional. Source ports involved in the alert. Values in this list MUST be integers and MUST be in the range 1-65535. GeoLocation Optional. GPS coordinates for the source. UnLocation Optional. Standard UN/Locode for the source. Location Optional. Internal name for the location of the source. Attachment Optional. Identifiers for attachments related to this source. Each identifier listed here MUST match the "Name" attribute for one of the attachments described using the Attachment class (Section 5.8). 5.6. The Target Class The Target class describes the target(s) impacted by the event(s) leading up to the alert. Lehmann Expires 18 October 2023 [Page 42] Internet-Draft IDMEFv2 April 2023 +------------------------+ | Target | +------------------------+ | IP IP | | STRING Hostname | | STRING Note | | STRING Service | | STRING User | | EMAIL Email | | INT[] Port | | GEOLOC GeoLocation | | UNLOCODE UnLocation | | STRING Location | | ID[] Attachment | +------------------------+ Figure 8: The Target class The Target class has the following attributes: IP Optional. Target IP address. Hostname Optional. Hostname of this target. This SHOULD be a fully qualified domain name, but may not conform exactly because values extracted from logs, messages, DNS, etc. may themselves be malformed. An empty string MAY be used to explicitly state that this value was inquired but not found (missing DNS entry). Note Optional. Free text human-readable additional note for this target. Service Optional. Service or process impacted by the alert. User Optional. User ID or login targeted by the alert. Email Optional. Email address targeted by the alert. E.g. the value of the "To" header inside a phishing e-mail. Lehmann Expires 18 October 2023 [Page 43] Internet-Draft IDMEFv2 April 2023 Port Optional. Target ports involved in the alert. Values in this list MUST be integers and MUST be in the range 1-65535. GeoLocation Optional. GPS coordinates for the target. UnLocation Optional. Standard UN/Locode for the target. Location Optional. Internal name for the location of the target. Attachment Optional. Identifiers for attachments related to this target. Each identifier listed here MUST match the "Name" attribute for one of the attachments described using the Attachment class (Section 5.8). 5.7. The Vector Class The Vector class describes the vector(s) of the event(s) leading up to the alert. • Name, location, description, … +-------------------------+ | Vector | +-------------------------+ | ENUM[] Category | | STRING ext-Category | | STRING Name | | STRING Note | | STRING[] TI | | GEOLOC GeoLocation | | FLOAT GeoRadius | | UNLOCODE UnLocation | | STRING Location | | ID[] Attachment | +-------------------------+ Figure 9: The Vector class The Vector class has the following attributes: Category Mandatory. Category for the detected "vector". Lehmann Expires 18 October 2023 [Page 44] Internet-Draft IDMEFv2 April 2023 +======+=================+================================+ | Rank | Keyword | Description | +======+=================+================================+ | 0 | Unknown | | +------+-----------------+--------------------------------+ | 1 | Face | | +------+-----------------+--------------------------------+ | 2 | RunningMan | | +------+-----------------+--------------------------------+ | 3 | Human | | +------+-----------------+--------------------------------+ | 4 | Man | | +------+-----------------+--------------------------------+ | 5 | Woman | | +------+-----------------+--------------------------------+ | 6 | Children | | +------+-----------------+--------------------------------+ | 7 | Animal | | +------+-----------------+--------------------------------+ | 8 | Object | | +------+-----------------+--------------------------------+ | 9 | Blast | | +------+-----------------+--------------------------------+ | 10 | Fire | | +------+-----------------+--------------------------------+ | 11 | Wind | | +------+-----------------+--------------------------------+ | 12 | Snow | | +------+-----------------+--------------------------------+ | 13 | Rain | | +------+-----------------+--------------------------------+ | 14 | Chemical | | +------+-----------------+--------------------------------+ | 15 | Smoke | | +------+-----------------+--------------------------------+ | 16 | Vapors | | +------+-----------------+--------------------------------+ | 17 | Drug | | +------+-----------------+--------------------------------+ | 18 | Device | | +------+-----------------+--------------------------------+ | 19 | Drone | | +------+-----------------+--------------------------------+ | 20 | Car | | +------+-----------------+--------------------------------+ | 21 | Truck | | +------+-----------------+--------------------------------+ | 22 | Vehicle | | Lehmann Expires 18 October 2023 [Page 45] Internet-Draft IDMEFv2 April 2023 +------+-----------------+--------------------------------+ | 23 | Bird | | +------+-----------------+--------------------------------+ | 24 | Storm | | +------+-----------------+--------------------------------+ | 25 | HighTemperature | | +------+-----------------+--------------------------------+ | 26 | Artifact | | +------+-----------------+--------------------------------+ | 27 | Autonomous | | | | System | | +------+-----------------+--------------------------------+ | 28 | Directory | | +------+-----------------+--------------------------------+ | 29 | Domain Name | | +------+-----------------+--------------------------------+ | 30 | Email Address | | +------+-----------------+--------------------------------+ | 31 | Email Message | | +------+-----------------+--------------------------------+ | 32 | File | | +------+-----------------+--------------------------------+ | 33 | IPv4 Address | | +------+-----------------+--------------------------------+ | 34 | IPv6 Address | | +------+-----------------+--------------------------------+ | 35 | Mutex | | +------+-----------------+--------------------------------+ | 36 | Network Traffic | | +------+-----------------+--------------------------------+ | 37 | Process | | +------+-----------------+--------------------------------+ | 38 | URL | | +------+-----------------+--------------------------------+ | 39 | User Account | | +------+-----------------+--------------------------------+ | 40 | Windows | | | | Registry Key | | +------+-----------------+--------------------------------+ | 41 | X509 | | | | Certificate | | +------+-----------------+--------------------------------+ | 42 | ext-value | A value used to indicate that | | | | this attribute is extended and | | | | the actual value is provided | | | | using the corresponding ext-* | | | | attribute. (see Section 4.1.1) | +------+-----------------+--------------------------------+ Lehmann Expires 18 October 2023 [Page 46] Internet-Draft IDMEFv2 April 2023 Table 9: Vector categories ext-Category Optional. A means by which to extend the Category attribute. (see Section 4.1.1) Name Optional. Name of the detected vector or "Unknown". Please note that this name does not need to be unique across vectors. Note Optional. Free text human-readable additional note for this vector. TI Optional. Threat Intelligence data about the vector. Values in this list MUST use the format "attribute:origin", where "attribute" refers to the attribute inside this vector found inside a Threat Intelligence database, and "origin" contains a short identifier for the Threat Intelligence database. E.g. "Name:FBI-Wanted". Please note that the same attribute may appear multiple times inside the list (because a match was found in multiple Threat Intelligence databases). GeoLocation Optional. GPS coordinates for the vector. GeoRadius Optional. Estimated radius around the provided geolocation in meters. This attribute can be interpreted as an error margin related to the detection of this vector. UnLocation Optional. Standard UN/Locode for the vector. Location Optional. Internal name for the location of the vector. Attachment Optional. Identifiers for attachments related to this vector. Lehmann Expires 18 October 2023 [Page 47] Internet-Draft IDMEFv2 April 2023 Each identifier listed here MUST match the "Name" attribute for one of the attachments described using the Attachment class (Section 5.8). 5.8. The Attachment Class The Attachment class contains additional data which was captured in relation with the event. +----------------------------+ | Attachment | +----------------------------+ | ID Name | | STRING FileName | | HASH[] Hash | | INT Size | | URI[] Ref | | URI[] ExternalURI | | STRING Note | | MEDIATYPE ContentType | | STRING ContentEncoding | | STRING Content | +----------------------------+ Figure 10: The Attachment class The Attachment class has the following attributes: Name Mandatory. A unique identifier among attachments that can be used to reference this attachment from other classes using the "Attachment" attribute. FileName Optional. Attachment filename. This will usually be the original name of the captured file or the name of the file containing the captured content (e.g. a packet capture file). Hash Optional. A list of hash results for the attachment's Content. Lehmann Expires 18 October 2023 [Page 48] Internet-Draft IDMEFv2 April 2023 The values in this list are computed by taking the raw value of the attachment's "Content" attribute. The hash result is computed before any other transformation (e.g. Base64 encoding) is applied to the content, so that a receiving IDMEF system may reverse the transformation, apply the same hashing function and obtain the same hash result. See also the definition for the "ContentEncoding" attribute below. It is RECOMMENDED that compatible implementations use one of the hashing functions from the SHA-2 [RFC6234] or SHA-3 [NIST.FIPS.202] families to compute the hash results in this list. Size Optional. Length of the content (in bytes). This value MUST be a non-negative integer. Ref Optional. References to sources of information related to the alert and/or vulnerability, and specific to this attachment. ExternalURI Optional. If the attachment's content is available and/or recognizable from an external resource, this is the URI (usually a URL) to that resource. This MAY also be a URN in a registered or unregistered ad-hoc namespace bearing reasonable information value and uniqueness, such as "urn:mhr:55eaf7effadc07f866d1eaed9c64e7ee49fe081a" or "magnet:?xt=urn:sha1:YNCKHTQCWBTRNJIV4WNAE52SJUQCZO5C". Note Optional. Free text human-readable additional note for this attachment. ContentType Optional. Internet Media Type of the attachment. For compatibility reasons, implementations SHOULD prefer one of the well-known media types registered in IANA . ContentEncoding Optional. Content encoding. The following encodings are defined in this version of the specification: Lehmann Expires 18 October 2023 [Page 49] Internet-Draft IDMEFv2 April 2023 * "json": The content refers to a JSON object which has been serialized to a string using the serialization procedure defined in [RFC8259]. * "base64": The content has been serialized using the Base64 encoding defined in [RFC4648]. The "base64" encoding SHOULD be used when the content contains binary data. If omitted, the "json" encoding MUST be assumed. Content Optional. The attachment's content, in case it is directly embedded inside the message. For large attachments, it is RECOMMENDED that implementations make use of the "ExternalURI" attribute to refererence a copy of the content saved in an external storage mechanism. 5.9. The JavaScript Object Notation Serialization Method This serialization method aims to convert IDMEFv2 messages to a format that is easy to parse and process, both by software/hardware processors, as well as humans. It relies on the the JavaScript Object Notation (JSON) Data Interchange Format defined in [RFC8259]. Conforming implementations MUST implement all the requirements specified in [RFC8259]. In addition, the following rules MUST be observed when serializing an IDMEFv2 message: * The top-level Alert class (Section 4.2) is represented as a JSON object ([RFC8259]). This JSON object is returned to the calling process at the end of the serialization process. * Aggregate classes are represented as JSON objects and stored as members of the top-level JSON object, using the same name as in the IDMEF data model. E.g. the appears under the name "Analyzer" inside the top-level JSON object. * Attributes are stored as members of the JSON object representing the class they belong to, using the same name as in the IDMEF data model. E.g. the "Version" attribute from the is stored under the name "Version" inside the top-level JSON object. Lehmann Expires 18 October 2023 [Page 50] Internet-Draft IDMEFv2 April 2023 * Lists from the IDMEF data model are represented as JSON arrays ([RFC8259]). This also applies to aggregate classes where a list is expected. E.g. the "Sensor" member inside the top-level JSON object contains a list of objects, where each object represents an instance of the . * The various string-based data types listed in Section 3 are represented as JSON strings ([RFC8259]). Please note that the issues outlined in [RFC8259] regarding strings processing also apply here. * IDMEF attributes with the "NUMBER" data type are represented as JSON numbers ([RFC8259]). 5.10. Attributes completeness The next table shows when each attributes is required depending on it's Type: physical, cyber or availability. Legend: * R: REQUIRED * r: Recommanded * o: Optional * NA: Not Applicable +===============+=================+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +===============+=================+=====+=====+=======+ | Alert | | | | | +===============+=================+=====+=====+=======+ | Version | String | R | R | R | +---------------+-----------------+-----+-----+-------+ | ID | UUID | R | R | R | +---------------+-----------------+-----+-----+-------+ | Entity | String | o | o | o | +---------------+-----------------+-----+-----+-------+ | Category | Array of ENUM | r | r | r | +---------------+-----------------+-----+-----+-------+ | Cause | ENUM | r | r | r | +---------------+-----------------+-----+-----+-------+ | Description | String | r | r | r | +---------------+-----------------+-----+-----+-------+ | Status | ENUM | r | r | r | +---------------+-----------------+-----+-----+-------+ Lehmann Expires 18 October 2023 [Page 51] Internet-Draft IDMEFv2 April 2023 | Priority | ENUM | r | r | r | +---------------+-----------------+-----+-----+-------+ | Confidence | Number | o | o | o | +---------------+-----------------+-----+-----+-------+ | Note | String | o | o | o | +---------------+-----------------+-----+-----+-------+ | CreateTime | Timestamp | R | R | R | +---------------+-----------------+-----+-----+-------+ | StartTime | Timestamp | r | r | r | +---------------+-----------------+-----+-----+-------+ | CeaseTime | Timestamp | o | o | o | +---------------+-----------------+-----+-----+-------+ | DeleteTime | Timestamp | o | o | o | +---------------+-----------------+-----+-----+-------+ | AltNames | Array of String | o | o | o | +---------------+-----------------+-----+-----+-------+ | AltCategory | Array of String | o | o | o | +---------------+-----------------+-----+-----+-------+ | Ref | Array of URI | o | o | o | +---------------+-----------------+-----+-----+-------+ | CorrelID | Array of UUID | o | o | o | +---------------+-----------------+-----+-----+-------+ | AggrCondition | Array of String | o | o | o | +---------------+-----------------+-----+-----+-------+ | PredID | Array of UUID | o | o | o | +---------------+-----------------+-----+-----+-------+ | RelID | Array of UUID | o | o | o | +---------------+-----------------+-----+-----+-------+ Table 10: Attributes completness - Alert Lehmann Expires 18 October 2023 [Page 52] Internet-Draft IDMEFv2 April 2023 +=============+===============+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +=============+===============+=====+=====+=======+ | Analyzer | Class | R | R | R | +=============+===============+=====+=====+=======+ | IP | IPAddress | R | R | R | +-------------+---------------+-----+-----+-------+ | Name | String | R | R | R | +-------------+---------------+-----+-----+-------+ | Hostname | String | r | r | r | +-------------+---------------+-----+-----+-------+ | Type | ENUM | r | r | r | +-------------+---------------+-----+-----+-------+ | Model | String | R | R | R | +-------------+---------------+-----+-----+-------+ | Category | Array of ENUM | R | R | R | +-------------+---------------+-----+-----+-------+ | Data | Array of ENUM | R | R | R | +-------------+---------------+-----+-----+-------+ | Method | Array of ENUM | R | R | R | +-------------+---------------+-----+-----+-------+ | GeoLocation | GeoLocation | r | o | o | +-------------+---------------+-----+-----+-------+ | UnLocation | UN/LOCODE | o | o | o | +-------------+---------------+-----+-----+-------+ | Location | String | o | o | o | +-------------+---------------+-----+-----+-------+ Table 11: Attributes completness - Analyzer Lehmann Expires 18 October 2023 [Page 53] Internet-Draft IDMEFv2 April 2023 +=============+================+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +=============+================+=====+=====+=======+ | Sensor | Array of Class | o | o | o | +=============+================+=====+=====+=======+ | IP | IPAddress | R | R | R | +-------------+----------------+-----+-----+-------+ | Name | String | R | R | R | +-------------+----------------+-----+-----+-------+ | Hostname | String | r | r | r | +-------------+----------------+-----+-----+-------+ | Model | String | R | R | R | +-------------+----------------+-----+-----+-------+ | UnLocation | UN/LOCODE | o | o | o | +-------------+----------------+-----+-----+-------+ | Location | String | o | o | o | +-------------+----------------+-----+-----+-------+ | CaptureZone | String | o | o | o | +-------------+----------------+-----+-----+-------+ Table 12: Attributes completness - Sensor Lehmann Expires 18 October 2023 [Page 54] Internet-Draft IDMEFv2 April 2023 +=============+=========================+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +=============+=========================+=====+=====+=======+ | Source | Array of Class | o | o | o | +=============+=========================+=====+=====+=======+ | UnLocation | UN/LOCODE | o | o | NA | +-------------+-------------------------+-----+-----+-------+ | Location | String | o | o | NA | +-------------+-------------------------+-----+-----+-------+ | GeoLocation | GeoLocation | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Note | String | o | o | o | +-------------+-------------------------+-----+-----+-------+ | TI | Array of String | o | o | o | +-------------+-------------------------+-----+-----+-------+ | IP | IPAddress | NA | r | NA | +-------------+-------------------------+-----+-----+-------+ | Hostname | String | NA | r | NA | +-------------+-------------------------+-----+-----+-------+ | User | String | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Email | String | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Protocol | Array of ProtocolName | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Port | Array of Port | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Attachment | Array of AttachmentName | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ Table 13: Attributes completness - Source Lehmann Expires 18 October 2023 [Page 55] Internet-Draft IDMEFv2 April 2023 +=============+=========================+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +=============+=========================+=====+=====+=======+ | Target | Array of Class | o | R | R | +=============+=========================+=====+=====+=======+ | UnLocation | UN/LOCODE | o | o | o | +-------------+-------------------------+-----+-----+-------+ | Location | String | r | o | o | +-------------+-------------------------+-----+-----+-------+ | GeoLocation | GeoLocation | o | o | o | +-------------+-------------------------+-----+-----+-------+ | Note | String | o | o | o | +-------------+-------------------------+-----+-----+-------+ | IP | IPAddress | o | r | R | +-------------+-------------------------+-----+-----+-------+ | Hostname | String | o | r | r | +-------------+-------------------------+-----+-----+-------+ | Service | String | NA | o | r | +-------------+-------------------------+-----+-----+-------+ | User | String | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Email | String | NA | o | NA | +-------------+-------------------------+-----+-----+-------+ | Port | Array of Port | NA | o | o | +-------------+-------------------------+-----+-----+-------+ | Attachment | Array of AttachmentName | NA | o | o | +-------------+-------------------------+-----+-----+-------+ Table 14: Attributes completness - Target Lehmann Expires 18 October 2023 [Page 56] Internet-Draft IDMEFv2 April 2023 +=============+=========================+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +=============+=========================+=====+=====+=======+ | Vector | Array of Class | o | o | o | +=============+=========================+=====+=====+=======+ | Category | Array of ENUM | R | R | NA | +-------------+-------------------------+-----+-----+-------+ | TI | Array of String | o | o | NA | +-------------+-------------------------+-----+-----+-------+ | Name | String | o | NA | NA | +-------------+-------------------------+-----+-----+-------+ | Size | ENUM | o | NA | NA | +-------------+-------------------------+-----+-----+-------+ | UnLocation | UN/LOCODE | o | NA | NA | +-------------+-------------------------+-----+-----+-------+ | GeoLocation | GeoLocation | o | NA | NA | +-------------+-------------------------+-----+-----+-------+ | GeoRadius | Number | o | NA | NA | +-------------+-------------------------+-----+-----+-------+ | Location | String | r | NA | NA | +-------------+-------------------------+-----+-----+-------+ | Note | String | o | NA | NA | +-------------+-------------------------+-----+-----+-------+ | Attachment | Array of AttachmentName | o | o | o | +-------------+-------------------------+-----+-----+-------+ Table 15: Attributes completness - Vector Lehmann Expires 18 October 2023 [Page 57] Internet-Draft IDMEFv2 April 2023 +=================+=================+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +=================+=================+=====+=====+=======+ | Attachment | Array of Class | o | o | o | +=================+=================+=====+=====+=======+ | Name | String | R | R | R | +-----------------+-----------------+-----+-----+-------+ | FileName | String | o | o | o | +-----------------+-----------------+-----+-----+-------+ | Hash | Array of Hashes | r | r | r | +-----------------+-----------------+-----+-----+-------+ | Size | Number | r | r | r | +-----------------+-----------------+-----+-----+-------+ | Ref | Array of URI | o | o | o | +-----------------+-----------------+-----+-----+-------+ | ExternalURI | Array of URI | o | o | o | +-----------------+-----------------+-----+-----+-------+ | Note | String | o | o | o | +-----------------+-----------------+-----+-----+-------+ | ContentType | MediaType | o | o | o | +-----------------+-----------------+-----+-----+-------+ | ContentEncoding | String | r | r | r | +-----------------+-----------------+-----+-----+-------+ | Content | String | o | o | o | +-----------------+-----------------+-----+-----+-------+ Table 16: Attributes completness - Attachment +============+========+=====+=====+=======+ | Attributes | Type | Phy | Cyb | Avail | +============+========+=====+=====+=======+ | Name | String | R | R | R | +============+========+=====+=====+=======+ | Reference | String | r | r | r | +------------+--------+-----+-----+-------+ | Content | String | R | R | R | +------------+--------+-----+-----+-------+ Table 17: Attributes completness 6. Security Considerations This document describes a data representation for exchanging security-related information between incident detection system implementations. Although there are no security concerns directly applicable to the format of this data, the data itself may contain security-sensitive information whose confidentiality, integrity, and/ or availability may need to be protected. Lehmann Expires 18 October 2023 [Page 58] Internet-Draft IDMEFv2 April 2023 This suggests that the systems used to collect, transmit, process, and store this data should be protected against unauthorized use and that the data itself should be protected against unauthorized access. The underlying messaging format and protocol used to exchange instances of the IDMEF MUST provide appropriate guarantees of confidentiality, integrity, and authenticity. The use of a standardized security protocol is encouraged. The draft-lehmann-idmefv2-https-transport-01.txt document defines the transportation of IDMEF over HTTPs that provides such security. 7. IANA Considerations This document creates 10 identically structured registries to be managed by IANA: * Name of the parent registry: "Incident Detection Message Exchange Format v2 (IDMEF)" * URL of the registry: * Namespace format: A registry entry consists of: - Value. A value for a given IDMEF attribute. It MUST conform to the formatting specified by the IDMEF "ENUM" data type (Section 3.3.1). - Description. A short description of the enumerated value. - Reference. An optional list of URIs to further describe the value. * Allocation policy: Expert Review per [RFC8126]. This reviewer will ensure that the requested registry entry conforms to the prescribed formatting. The reviewer will also ensure that the entry is an appropriate value for the attribute per the information model (Section 5). Lehmann Expires 18 October 2023 [Page 59] Internet-Draft IDMEFv2 April 2023 The registries to be created are named in the "Registry Name" column of Table 18. Each registry is initially populated with values and descriptions that come from an attribute specified in the IDMEF model (Section 5). The initial values for the Value and Description fields of a given registry are listed in "Initial Values". The "Initial Values" column points to a table in this document that lists and describes each enumerated value. Each enumerated value in the table gets a corresponding entry in a given registry. The initial value of the Reference field of every registry entry described below should be this document. +===================+========================================+ | Registry Name | Initial Values | +===================+========================================+ | Alert-Category | Table 1 (Alert class (Section 5.2)) | +-------------------+----------------------------------------+ | Alert-Cause | Table 2 (Alert class (Section 5.2)) | +-------------------+----------------------------------------+ | Alert-Priority | Table 4 (Alert class (Section 5.2)) | +-------------------+----------------------------------------+ | Alert-Status | Table 3 (Alert class (Section 5.2)) | +-------------------+----------------------------------------+ | Analyzer-Category | Table 6 (Alert class (Section 5.2)) | +-------------------+----------------------------------------+ | Analyzer-Data | Table 7 (Analyzer class (Section 5.3)) | +-------------------+----------------------------------------+ | Analayzer-Method | Table 8 (Analyzer class (Section 5.3)) | +-------------------+----------------------------------------+ | Analyzer-Type | Table 5 (Analyzer class (Section 5.3)) | +-------------------+----------------------------------------+ | Vector-Category | Table 9 (Vector (Section 5.7)) | +-------------------+----------------------------------------+ Table 18: IANA Enumerated Value Registries 8. Acknowledgement The following groups and individuals contributed to the creation of this document and should be recognized for their efforts. * The former Prelude SIEM team : Thomas Andrejak & François Poirotte (Co-authors of the first version of this document), Antoine Luong, Song Tran, Selim Menouar and Camille Gardet * The core members of the SECEF (SECurity Exchange Format) consortium : Herve Debar (Author of RFC 4765 - IDMEFv1), Guillaume Hiet and François Dechelle Lehmann Expires 18 October 2023 [Page 60] Internet-Draft IDMEFv2 April 2023 * The H2020 7SHIELD project (Safety and Security Standards of Space Systems, ground Segments and Satellite data assets , via prevention, detection, response and mitigation of physical and cyber threats) who implemented in real scale first versions of IDMEFv2 on five pilots around Europe helping greatly to improve it. * The CESNET team for their work on the [IDEA0] format (based on IDMEFv1) which inspired multiples concepts to IDMEFv2. * The [ENISA-RIST] Reference Security Incident Taxonomy Working Group 9. References 9.1. Normative References [RFC5321] Klensin, J., "Simple Mail Transfer Protocol", RFC 5321, DOI 10.17487/RFC5321, October 2008, . [RFC2046] Freed, N. and N. Borenstein, "Multipurpose Internet Mail Extensions (MIME) Part Two: Media Types", RFC 2046, DOI 10.17487/RFC2046, November 1996, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC5322] Resnick, P., Ed., "Internet Message Format", RFC 5322, DOI 10.17487/RFC5322, October 2008, . [RFC3339] Klyne, G. and C. Newman, "Date and Time on the Internet: Timestamps", RFC 3339, DOI 10.17487/RFC3339, July 2002, . [RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986, DOI 10.17487/RFC3986, January 2005, . [RFC4122] Leach, P., Mealling, M., and R. Salz, "A Universally Unique IDentifier (UUID) URN Namespace", RFC 4122, DOI 10.17487/RFC4122, July 2005, . Lehmann Expires 18 October 2023 [Page 61] Internet-Draft IDMEFv2 April 2023 [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006, . [RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data Encodings", RFC 4648, DOI 10.17487/RFC4648, October 2006, . [RFC5234] Crocker, D., Ed. and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68, RFC 5234, DOI 10.17487/RFC5234, January 2008, . [RFC5952] Kawamura, S. and M. Kawashima, "A Recommendation for IPv6 Address Text Representation", RFC 5952, DOI 10.17487/RFC5952, August 2010, . [RFC8259] Bray, T., Ed., "The JavaScript Object Notation (JSON) Data Interchange Format", STD 90, RFC 8259, DOI 10.17487/RFC8259, December 2017, . [UNICODE] Unicode Consortium, "Unicode Standard", version 14.0.0, 14 September 2021, . [ENISA-RIST] ENISA, "Reference Incident Classification Taxonomy", 26 January 2018, . [IANA_media_types] IANA, "Media Types", 10 October 2022, . [IANA_hash_function_text_names] IANA, "Hash Function Textual Names", 21 April 2006, . [UN-LOCODE] UNECE, "UN/LOCODE Code List by Country and Territory", 6 July 2021, . 9.2. Informative References Lehmann Expires 18 October 2023 [Page 62] Internet-Draft IDMEFv2 April 2023 [RFC4765] Debar, H., Curry, D., and B. Feinstein, "The Intrusion Detection Message Exchange Format (IDMEF)", RFC 4765, DOI 10.17487/RFC4765, March 2007, . [RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017, . [RFC6234] Eastlake 3rd, D. and T. Hansen, "US Secure Hash Algorithms (SHA and SHA-based HMAC and HKDF)", RFC 6234, DOI 10.17487/RFC6234, May 2011, . [NIST.FIPS.202] Dworkin, Morris J., "SHA-3 Standard: Permutation-Based Hash and Extendable-Output Functions", NIST NIST FIPS 202, DOI 10.6028/NIST.FIPS.202, July 2015, . [WGS84] National Imagery and Mapping Agency, "Department of Defense World Geodetic System 1984: Its Definition and Relationships with Local Geodetic Systems", Third Edition, 1984, . [IDEA0] CESNET, "Intrusion Detection Extensible Alert version 0", 25 September 2015, . Appendix A. Examples This section contains several examples of events/incidents which may be described using the IDMEF Data Model defined in. For each example, the serialization method listed in Section 5 was used on the original IDMEF message to produce a JSON representation. A.1. Physical intrusion Listing 1 describes an incident where an unidentified man was detected on company premises near the building where server room A is located. Lehmann Expires 18 October 2023 [Page 63] Internet-Draft IDMEFv2 April 2023 { "Version": "2.0", "ID": "819df7bc-35ef-40d8-bbee-1901117370b1", "Description": "Potential intruder detected", "Priority": "Low", "Status": "Incident", "Cause": "Malicious", "CreateTime": "2021-05-10T16:52:13.075994+00:00", "StartTime": "2021-05-10T16:52:13+00:00", "Category": [ "Intrusion.Burglary" ], "Analyzer": { "Name": "BigBrother", "Hostname": "bb.acme.com", "Type": "Physical", "Model": "Big Brother v42", "Category": [ "HAR", "FRC" ], "Data": [ "Images" ], "Method": [ "Movement", "Biometric", "AI" ], "IP": "192.0.2.1" }, "Sensor": [ { "IP": "192.0.2.2", "Name": "Camera #23", "Model": "SuperDuper Camera v1", "Location": "Hallway to server room A1" } ], "Source": [ { "Note": "Black Organization, aka. APT 4869" } ], "Vector": [ { "Category": ["Man"], "TI": ["Name:FBI-Wanted"], Lehmann Expires 18 October 2023 [Page 64] Internet-Draft IDMEFv2 April 2023 "Name": "John Doe", "Note": "Codename Vodka, known henchman for APT 4869", "Location": "Hallway to server room A1", "Attachment": ["pic01", "wanted"] } ], "Attachment": [ { "Name": "wanted", "FileName": "fbi-wanted-poster.jpg", "Size": 1234567, "Ref": ["https://www.fbi.gov/wanted/topten"], "ContentType": "image/jpg", "ContentEncoding": "base64", "Content": "..." }, { "Name": "pic01", "Note": "Hi-res picture showing John Doe near server room A1", "ExternalURI": ["ftps://192.0.2.1/cam23/20210510165211.jpg"], "ContentType": "image/jpg" } ] } A.2. Cyberattack Listing 2 describes an incident related to a potential bruteforce attack against the "root" user account of the server at 192.0.2.2 and 2001:db8::/32. { "Version": "2.0", "ID": "819df7bc-35ef-40d8-bbee-1901117370b2", "Description": "Potential bruteforce attack on root user account", "Priority": "Medium", "CreateTime": "2021-05-10T16:55:29.196408+00:00", "StartTime": "2021-05-10T16:55:29+00:00", "Category": [ "Attempt.Login" ], "Analyzer": { "Name": "SIEM", "Hostname": "siem.acme.com", "Type": "Cyber", "Model": "Concerto SIEM 5.2", "Category": [ "SIEM", Lehmann Expires 18 October 2023 [Page 65] Internet-Draft IDMEFv2 April 2023 "LOG" ], "Data": [ "Log" ], "Method": [ "Monitor", "Signature" ], "IP": "192.0.2.1" }, "Sensor": [ { "IP": "192.0.2.5", "Name": "syslog", "Hostname": "www.acme.com", "Model": "rsyslog 8.2110", "Location": "Server room A1, rack 10" } ], "Target": [ { "IP": "192.0.2.2", "Hostname": "www.acme.com", "Location": "Server room A1, rack 10", "User": "root" }, { "IP": "2001:db8::/32", "Hostname": "www.acme.com", "Location": "Server room A1, rack 10", "User": "root" } ] } A.3. Server outage Listing 3 describes an incident where the webserver at "www.example.com" encountered some kind of failure condition resulting in an outage. Lehmann Expires 18 October 2023 [Page 66] Internet-Draft IDMEFv2 April 2023 { "Version": "2.0", "ID": "819df7bc-35ef-40d8-bbee-1901117370b3", "Description": "A server did not reply to an ICMP ping request", "Priority": "Medium", "Status": "Incident", "Cause": "Unknown", "CreateTime": "2021-05-10T16:59:11.875209+00:00", "StartTime": "2021-05-10T16:59:11.875209+00:00", "Category": [ "Availability.Outage" ], "Analyzer": { "Name": "NMS", "Hostname": "nms.example.com", "Type": "Availability", "Model": "Concerto NMS 5.2", "Category": [ "NMS" ], "Data": [ "Network" ], "Method": [ "Monitor" ], "IP": "192.0.2.1" }, "Target": [ { "IP": "192.168.1.2", "Hostname": "www.acme.com", "Service": "website", "Location": "Server room A1, rack 10" } ] } A.4. Combined incident Listing 4 describes a combined incident resulting from the correlation of the previous physical, cyber and availability incidents. Lehmann Expires 18 October 2023 [Page 67] Internet-Draft IDMEFv2 April 2023 { "Version": "2.0", "ID": "819df7bc-35ef-40d8-bbee-1901117370b4", "Description": "Intrusion and Sabotage detected", "Prioriy": "High", "Status": "Incident", "Cause": "Malicious", "CreateTime": "2021-05-10T16:59:15.075994+00:00", "StartTime": "2021-05-10T16:52:11+00:00", "Category": [ "Intrusion.Burglary", "Attempt.Login", "Intrusion.SysCompromise", "Availability.Outage", "Availability.Sabotage", "Availability.Failure" ], "CorrelID": [ "819df7bc-35ef-40d8-bbee-1901117370b1", "819df7bc-35ef-40d8-bbee-1901117370b2", "819df7bc-35ef-40d8-bbee-1901117370b3" ], "Analyzer": { "Name": "Correlator", "Hostname": "correlator.acme.com", "Type": "Combined", "Model": "Concerto Hybrid Correlator v5.2", "Category": [ ], "Data": [ "Alert" ], "Method": [ "Correlation" ], "IP": "192.0.2.1" }, "Source": [ { "Note": "Black Organization, aka. APT 4869" } ], "Vector": [ { "Category": ["Man"], "TI": ["Name:FBI-Wanted"], "Name": "John Doe", "Note": "Codename Vodka, known henchman for APT 4869", Lehmann Expires 18 October 2023 [Page 68] Internet-Draft IDMEFv2 April 2023 "Size": "Medium" } ], "Target": [ { "Location": "Server room A1" }, { "IP": "192.0.2.2", "Hostname": "www.acme.com", "User": "root" }, { "IP": "192.0.2.2", "Hostname": "www.acme.com", "Service": "website" } ] } Appendix B. JSON Validation Schema (Non-normative) Listing 5 contains a JSON Schema that can be used to validate incoming IDMEF messages prior to processing. Please note that extraneous linebreaks have been included due to formatting constraints. { "description": "JSON schema for the Intrusion Detection Message Exchange Format (IDMEF) version 2 (revision 2.D.V01)", "properties": { "Version": { "description": "The version of the IDMEF format in use by this alert. During the drafts tuning period the version is equal to the draft version. Therefore it is \"2.D.V01\" for Draft V01.", "enum": [ "2.D.V01" ] }, "ID": { "description": "Unique identifier for the alert.", "$ref": "#/definitions/uuidType" }, "Entity": { "description": "Tenant ID to support multi-tenancy (e.g. decentralized infrastructure, local agency, subsidiary company, etc.). Should be used when there are multiple sites/locations or multiple tenants (e.g. by Managed Security Services Providers).", "type": "string" }, "Category": { "description": "The incident's category & subcategory as listed in using the format \"category.subcategory\" (e.g. \"Attempt.Exploit\").", "type": "array", "items": { Lehmann Expires 18 October 2023 [Page 69] Internet-Draft IDMEFv2 April 2023 "$ref": "#/definitions/categoryEnum" } }, "ext-Category": { "description": "A means by which to extend the Category attribute. (see )", "type": "string" }, "Cause": { "description": "Alert cause. The cause can be modified by any analyser on the way of the alert and later by the operator and/or the analyst if new investigation reveals and confirms a different cause of the event.", "$ref": "#/definitions/causeEnum" }, "Description": { "description": "Short free text human-readable description of the event. The description can add detail to the alert classification for easiest/faster comprehension by the operator. Example : * Cryptoware WannaCry blocked on pegasus server * Unknown person entering through east doorway", "type": "string" }, "Status": { "description": "Event state in the overall event lifecycle.", "$ref": "#/definitions/statusEnum" }, "Priority": { "description": "Priority of the alert. Priority is defined by conbining impact and urgency. It indicates how fast the incident should be taken care of. Impact defines the enormity of the situation and mostly deals with \u201cHow Many\u201d or \u201chow much\u201d question. It can be in terms of people, finances, systems, etc. How many people and/or systems impacted, how badly are they impacted (is there potential physical impact ?) , how much financial loss, severity of legal liabilities,... Impact could be considered equivalent to \"Severity\". Urgency is associated with time. The time it takes to have the perceived Impact. For example, a high impact incident may have low urgency if the impact will not affect the business until the end of the financial year.", "$ref": "#/definitions/priorityEnum" }, "Confidence": { "description": "A floating-point value between 0 and 1 indicating the analyzer's confidence in its own reliability of this particular detection, where 0 means that the detection is surely incorrect while 1 means there is no doubt about the detection made.", "type": "number" }, "Note": { "description": "Free text human-readable additional note, possibly a longer description of the incident if is not already obvious. The Note attribute can be used to store any additional information. It can be additional information about the event and/or about the incident resolution, although the incident resolution information should in principle be stored elsewhere (with a link with the external tool in AltNames)", "type": "string" }, "CreateTime": { "description": "Timestamp indicating when the message was created.", "$ref": "#/definitions/timestampType" }, "StartTime": { "description": "Timestamp indicating the deduced start of the event. StartTime can be later than CreateTime in case or Alerts created from forecast information (e.g. Snow Storm in two days staring at 10h00)", "$ref": "#/definitions/timestampType" }, "EndTime": { "description": "Timestamp indicating the deduced end of the event.", "$ref": "#/definitions/timestampType" }, "AltNames": { "description": "Alternative identifiers; strings which help pair the event to internal systems' information (for example ticket IDs inside a request tracking systems).", "type": "array", "items": { "type": "string" Lehmann Expires 18 October 2023 [Page 70] Internet-Draft IDMEFv2 April 2023 } }, "AltCategory": { "description": "Alternate categories from a reference other than (e.g. MISP, MITRE ATT@CK or another proprietary/internal reference).", "type": "array", "items": { "type": "string" } }, "Ref": { "description": "References to sources of information related to the alert and/or vulnerability, and specific to this alert. This MAY be a URL to additional info, or a URN in a registered or unregistered ad-hoc namespace bearing reasonable information value and uniqueness, such as \"urn:cve:CVE-2013-2266\".", "type": "array", "items": { "type": "string", "format": "uri" } }, "CorrelID": { "description": "Identifiers for the messages which were used as information sources to create this message, in case the message has been created based on correlation/analysis/deduction from other messages.", "type": "array", "items": { "$ref": "#/definitions/uuidType" } }, "AggrCondition": { "description": "A list of IDMEF fields used to aggregate events. The values for these fields will be the same in all aggregated events. This attribute should mostly be set by intermediary nodes, which detect duplicates, or aggregate events, spanning multiple detection windows, into a longer one. The \"StartTime\" and \"EndTime\" attributes are used in conjunction with this attribute to describe the aggregation window.", "type": "array", "items": { "type": "string" } }, "PredID": { "description": "A list containing the identifiers of previous messages which are obsoleted by this message. The obsoleted alerts SHOULD NOT be used anymore. This field can be used to \"update\" an alert.", "type": "array", "items": { "$ref": "#/definitions/uuidType" } }, "RelID": { "description": "A list containing the identifiers of other messages related to this message.", "type": "array", "items": { "$ref": "#/definitions/uuidType" } }, "Analyzer": { "type": "object", "items": { Lehmann Expires 18 October 2023 [Page 71] Internet-Draft IDMEFv2 April 2023 "description": "The Analyzer class describes the module that has analyzed the data captured by the sensors, identified an event of interest and decided to create an alert.", "properties": { "IP": { "description": "Analyzer IP address.", "$ref": "#/definitions/ipType" }, "Name": { "description": "Name of the analyzer, which must be reasonably unique, however still bear some meaningful sense. This attribute usually denotes the hierarchy of organizational units the detector belongs to and its own name. It MAY also be used to distinguish multiple analyzers running with the same IP address.", "type": "string" }, "Hostname": { "description": "Hostname of this analyzer. SHOULD be a fully-qualified domain name.", "type": "string" }, "Model": { "description": "Analyzer model description (usually its generic name, brand and version).", "type": "string" }, "Type": { "description": "Analyzer type.", "type": "array", "items": { "$ref": "#/definitions/analyzerTypeEnum" } }, "Category": { "description": "Analyzer categories.", "type": "array", "items": { "$ref": "#/definitions/analyzerCategoryEnum" } }, "ext-Category": { "description": "A means by which to extend the Category attribute. (see )", "type": "string" }, "Data": { "description": "Type of data analyzed during the detection.", "type": "array", "items": { "$ref": "#/definitions/analyzerDataEnum" } }, "ext-Data": { "description": "A means by which to extend the Data attribute. (see )", "type": "string" }, "Method": { Lehmann Expires 18 October 2023 [Page 72] Internet-Draft IDMEFv2 April 2023 "description": "Detection method.", "type": "array", "items": { "$ref": "#/definitions/analyzerMethodEnum" } }, "ext-Method": { "description": "A means by which to extend the Method attribute. (see )", "type": "string" }, "GeoLocation": { "description": "GPS coordinates for the analyzer.", "$ref": "#/definitions/geolocType" }, "UnLocation": { "description": "Standard UN/Locode for the analyzer.", "$ref": "#/definitions/unlocodeType" }, "Location": { "description": "Internal name for the location of the analyzer.", "type": "string" } }, "additionalProperties": false, "type": "object", "required": [ "IP", "Name" ] } }, "Sensor": { "type": "array", "items": { "description": "The Sensor class describes the module that captured the data before sending it to an analyzer. The Sensor may be a subpart of the Analyzer.", "properties": { "IP": { "description": "The sensor's IP address.", "$ref": "#/definitions/ipType" }, "Name": { "description": "Name of the sensor, which must be reasonably unique, however still bear some meaningful sense. This attribute usually denotes the hierarchy of organizational units the sensor belongs to and its own name. It MAY also be used to distinguish multiple sensors running with the same IP address.", "type": "string" }, "Hostname": { "description": "The sensor's hostname. This SHOULD be a fully qualified domain name, but may not conform exactly because values extracted from logs, messages, DNS, etc. may themselves be malformed. An empty string MAY be used to explicitly state that this value was inquired but not found (missing DNS entry).", "type": "string" }, Lehmann Expires 18 October 2023 [Page 73] Internet-Draft IDMEFv2 April 2023 "Model": { "description": "The sensor model's description (usually its generic name, brand and version).", "type": "string" }, "GeoLocation": { "description": "GPS coordinates for the analyzerr.", "$ref": "#/definitions/geolocType" }, "UnLocation": { "description": "Standard UN/Locode for the sensor.", "$ref": "#/definitions/unlocodeType" }, "Location": { "description": "Internal name for the location of the sensor.", "type": "string" }, "CaptureZone": { "description": "A string that describes the \"capture zone\" of the sensor, as a JSON-serialized string. Depending on the type of sensor, the capture zone may for instance refer to: \n- A JSON object describing a camera's settings (elevation, horizontal and vertical field of view, azimuth, etc.)\n- A description of the IP network where packet capture is taking place.", "type": "string" } }, "additionalProperties": false, "type": "object", "required": [ "IP", "Name" ] } }, "Source": { "type": "array", "items": { "description": "The Source class describes the origin(s) of the event(s) leading up to the alert.", "properties": { "IP": { "description": "Source IP address.", "$ref": "#/definitions/ipType" }, "Hostname": { "description": "Hostname of this source. This SHOULD be a fully qualified domain name, but may not conform exactly because values extracted from logs, messages, DNS, etc. may themselves be malformed. An empty string MAY be used to explicitly state that this value was inquired but not found (missing DNS entry).", "type": "string" }, "Note": { "description": "Free text human-readable additional note for this source.", "type": "string" }, "TI": { "description": "Threat Intelligence data about the source. Values in this list MUST use the format \"attribute:origin\", where \"attribute\" refers to the attribute inside this source found inside a Threat Intelligence database, and \"origin\" contains a short identifier for the Threat Intelligence database. E.g. \"IP:Dshield\". Please note that the same attribute may appear multiple times inside the list (because a match was found in multiple Threat Intelligence databases).", Lehmann Expires 18 October 2023 [Page 74] Internet-Draft IDMEFv2 April 2023 "type": "array", "items": { "type": "string" } }, "User": { "description": "User ID or login responsible for the alert.", "type": "string" }, "Email": { "description": "Email address responsible for the alert. E.g. the value of the \"Reply-To\" or \"From\" header inside a phishing e-mail.", "type": "string", "format": "email" }, "Protocol": { "description": "Protocols related to connections from/to this source. If several protocols are stacked, they MUST be ordered from the lowest (the closest to the medium) to the highest (the closest to the application) according to the ISO/OSI model.", "type": "array", "items": { "$ref": "#/definitions/protocolType" } }, "Port": { "description": "Source ports involved in the alert. Values in this list MUST be integers and MUST be in the range 1-65535.", "type": "array", "items": { "type": "integer" } }, "GeoLocation": { "description": "GPS coordinates for the source.", "$ref": "#/definitions/geolocType" }, "UnLocation": { "description": "Standard UN/Locode for the source.", "$ref": "#/definitions/unlocodeType" }, "Location": { "description": "Internal name for the location of the source.", "type": "string" }, "Attachment": { "description": "Identifiers for attachments related to this source. Each identifier listed here MUST match the \"Name\" attribute for one of the attachments described using the Attachment class .", "type": "array", "items": { "$ref": "#/definitions/attachmentNameType" } } }, Lehmann Expires 18 October 2023 [Page 75] Internet-Draft IDMEFv2 April 2023 "additionalProperties": false, "type": "object" } }, "Target": { "type": "array", "items": { "description": "The Target class describes the target(s) impacted by the event(s) leading up to the alert.", "properties": { "IP": { "description": "Target IP address.", "$ref": "#/definitions/ipType" }, "Hostname": { "description": "Hostname of this target. This SHOULD be a fully qualified domain name, but may not conform exactly because values extracted from logs, messages, DNS, etc. may themselves be malformed. An empty string MAY be used to explicitly state that this value was inquired but not found (missing DNS entry).", "type": "string" }, "Note": { "description": "Free text human-readable additional note for this target.", "type": "string" }, "Service": { "description": "Service or process impacted by the alert.", "type": "string" }, "User": { "description": "User ID or login targeted by the alert.", "type": "string" }, "Email": { "description": "Email address targeted by the alert. E.g. the value of the \"To\" header inside a phishing e-mail.", "type": "string", "format": "email" }, "Port": { "description": "Target ports involved in the alert. Values in this list MUST be integers and MUST be in the range 1-65535.", "type": "array", "items": { "type": "integer" } }, "GeoLocation": { "description": "GPS coordinates for the target.", "$ref": "#/definitions/geolocType" }, "UnLocation": { "description": "Standard UN/Locode for the target.", "$ref": "#/definitions/unlocodeType" Lehmann Expires 18 October 2023 [Page 76] Internet-Draft IDMEFv2 April 2023 }, "Location": { "description": "Internal name for the location of the target.", "type": "string" }, "Attachment": { "description": "Identifiers for attachments related to this target. Each identifier listed here MUST match the \"Name\" attribute for one of the attachments described using the Attachment class .", "type": "array", "items": { "$ref": "#/definitions/attachmentNameType" } } }, "additionalProperties": false, "type": "object" } }, "Vector": { "type": "array", "items": { "description": "The Vector class describes the vector(s) of the event(s) leading up to the alert. \u2022 Name, location, description, \u2026", "properties": { "Category": { "description": "Category for the detected \"vector\".", "type": "array", "items": { "$ref": "#/definitions/vectorCategoryEnum" } }, "ext-Category": { "description": "A means by which to extend the Category attribute. (see )", "type": "string" }, "Name": { "description": "Name of the detected vector or \"Unknown\". Please note that this name does not need to be unique across vectors.", "type": "string" }, "Note": { "description": "Free text human-readable additional note for this vector.", "type": "string" }, "TI": { "description": "Threat Intelligence data about the vector. Values in this list MUST use the format \"attribute:origin\", where \"attribute\" refers to the attribute inside this vector found inside a Threat Intelligence database, and \"origin\" contains a short identifier for the Threat Intelligence database. E.g. \"Name:FBI-Wanted\". Please note that the same attribute may appear multiple times inside the list (because a match was found in multiple Threat Intelligence databases).", "type": "array", "items": { "type": "string" } }, Lehmann Expires 18 October 2023 [Page 77] Internet-Draft IDMEFv2 April 2023 "GeoLocation": { "description": "GPS coordinates for the vector.", "$ref": "#/definitions/geolocType" }, "GeoRadius": { "description": "Estimated radius around the provided geolocation in meters. This attribute can be interpreted as an error margin related to the detection of this vector.", "type": "number" }, "UnLocation": { "description": "Standard UN/Locode for the vector.", "$ref": "#/definitions/unlocodeType" }, "Location": { "description": "Internal name for the location of the vector.", "type": "string" }, "Attachment": { "description": "Identifiers for attachments related to this vector. Each identifier listed here MUST match the \"Name\" attribute for one of the attachments described using the Attachment class .", "type": "array", "items": { "$ref": "#/definitions/attachmentNameType" } } }, "additionalProperties": false, "type": "object", "required": [ "Category" ] } }, "Attachment": { "type": "array", "items": { "description": "The Attachment class contains additional data which was captured in relation with the event.", "properties": { "Name": { "description": "A unique identifier among attachments that can be used to reference this attachment from other classes using the \"Attachment\" attribute.", "$ref": "#/definitions/attachmentNameType" }, "FileName": { "description": "Attachment filename. This will usually be the original name of the captured file or the name of the file containing the captured content (e.g. a packet capture file).", "type": "string" }, "Hash": { "description": "A list of hash results for the attachment's Content. The values in this list are computed by taking the raw value of the attachment's \"Content\" attribute. The hash result is computed before any other transformation (e.g. Base64 encoding) is applied to the content, so that a receiving IDMEF system may reverse the transformation, apply the same hashing function and obtain the same hash result. See also the definition for the \"ContentEncoding\" attribute below. It is RECOMMENDED that compatible implementations use one of the hashing functions from the SHA-2 or SHA-3 families to compute the hash results in this list.", "type": "array", "items": { Lehmann Expires 18 October 2023 [Page 78] Internet-Draft IDMEFv2 April 2023 "$ref": "#/definitions/hashType" } }, "Size": { "description": "Length of the content (in bytes). This value MUST be a non-negative integer.", "type": "integer" }, "Ref": { "description": "References to sources of information related to the alert and/or vulnerability, and specific to this attachment.", "type": "array", "items": { "type": "string", "format": "uri" } }, "ExternalURI": { "description": "If the attachment's content is available and/or recognizable from an external resource, this is the URI (usually a URL) to that resource. This MAY also be a URN in a registered or unregistered ad-hoc namespace bearing reasonable information value and uniqueness, such as \"urn:mhr:55eaf7effadc07f866d1eaed9c64e7ee49fe081a\" or \"magnet:?xt=urn:sha1:YNCKHTQCWBTRNJIV4WNAE52SJUQCZO5C\".", "type": "array", "items": { "type": "string", "format": "uri" } }, "Note": { "description": "Free text human-readable additional note for this attachment.", "type": "string" }, "ContentType": { "description": "Internet Media Type of the attachment. For compatibility reasons, implementations SHOULD prefer one of the well-known media types registered in IANA .", "$ref": "#/definitions/mediatypeType" }, "ContentEncoding": { "description": "Content encoding. The following encodings are defined in this version of the specification: \n- \"json\": The content refers to a JSON object which has been serialized to a string using the serialization procedure defined in .\n- \"base64\": The content has been serialized using the Base64 encoding defined in . The \"base64\" encoding SHOULD be used when the content contains binary data. If omitted, the \"json\" encoding MUST be assumed.", "type": "string" }, "Content": { "description": "The attachment's content, in case it is directly embedded inside the message. For large attachments, it is RECOMMENDED that implementations make use of the \"ExternalURI\" attribute to refererence a copy of the content saved in an external storage mechanism.", "type": "string" } }, "additionalProperties": false, "type": "object", "required": [ "Name" ] } } }, Lehmann Expires 18 October 2023 [Page 79] Internet-Draft IDMEFv2 April 2023 "additionalProperties": false, "type": "object", "required": [ "Analyzer", "Version", "ID", "CreateTime" ], "definitions": { "categoryEnum": { "enum": [ "Abusive.Spam", "Abusive.Harassment", "Abusive.Illicit", "Malicious.System", "Malicious.Botnet", "Malicious.Distribution", "Malicious.Configuration", "Recon.Scanning", "Recon.Sniffing", "Recon.SocialEngineering", "Attempt.Exploit", "Attempt.Login", "Attempt.NewSignature", "Intrusion.AdminCompromise", "Intrusion.UserCompromise", "Intrusion.AppCompromise", "Intrusion.SysCompromise", "Intrusion.Burglary", "Availability.DoS", "Availability.DDoS", "Availability.Misconf", "Availability.Theft", "Availability.Sabotage", "Availability.Outage", "Availability.Failure", "Information. UnauthorizedAccess", "Information. UnauthorizedModification", "Information.DataLoss", "Information.DataLeak", "Fraud.UnauthorizedUsage", "Fraud.Copyright", "Fraud.Masquerade", "Fraud.Phishing", "Vulnerable.Crypto", "Vulnerable.DDoS", "Vulnerable.Surface", "Vulnerable.Disclosure", Lehmann Expires 18 October 2023 [Page 80] Internet-Draft IDMEFv2 April 2023 "Vulnerable.System", "Geophysical.Earthquake", "Geophysical.MassMovement", "Geophysical.Volcanic", "Meteorological. Temperature", "Meteorological.Fog", "Meteorological.Storm", "Hydrological.Flood", "Hydrological.Landslide", "Hydrological.Wave", "Climatological.Drought", "Climatological. LakeOutburst", "Climatological.Wildfire", "Biological.Epidemic", "Biological.Insect", "Biological.Animal", "Extraterrestrial.Impact", "Extraterrestrial. SpaceWeather", "Other.Uncategorised", "Other.Undetermined", "Test.Test", "ext-value" ], "description": "Possible alert category" }, "causeEnum": { "enum": [ "Normal", "Error", "Malicious", "Malfunction", "Hazard", "Unknown" ], "description": "Possible alert cause" }, "statusEnum": { "enum": [ "Event", "Incident" ], "description": "Possible alert status" }, "priorityEnum": { "enum": [ "Unknown", "Info", "Low", Lehmann Expires 18 October 2023 [Page 81] Internet-Draft IDMEFv2 April 2023 "Medium", "High" ], "description": "Possible alert priority" }, "analyzerTypeEnum": { "enum": [ "Cyber", "Physical", "Availability", "Combined" ], "description": "Possible analyzer type" }, "analyzerCategoryEnum": { "enum": [ "1DLiS", "2DLiS", "3DLiS", "1DLaS", "2DLaS", "3DLaS", "VAD", "HAR", "FRC", "VNIR", "SWIR", "MWIR", "LWIR", "ADS", "ODC", "DDOS", "SPAM", "AV", "EDR", "FW", "NIDS", "HIDS", "WIDS", "PROX", "WAF", "HPT", "LOG", "IAM", "VPN", "ETL", "RASP", "BAST", Lehmann Expires 18 October 2023 [Page 82] Internet-Draft IDMEFv2 April 2023 "NAC", "SIEM", "NMS", "ext-value" ], "description": "Possible analyzer category" }, "analyzerDataEnum": { "enum": [ "Light", "Noise", "Touch", "Images", "Vibrations", "Lidar", "Thermic", "Seismic", "Temperature", "Rain", "Water", "Humidity", "Particles", "Contact", "MagneticField", "Acoustics", "Fog", "External", "Reporting", "Connection", "Datagram", "Content", "Data", "File", "Flow", "Log", "Protocol", "Host", "Network", "Alert", "Relay", "Auth", "SNMP", "ext-value" ], "description": "Possible analyzer data" }, "analyzerMethodEnum": { "enum": [ Lehmann Expires 18 October 2023 [Page 83] Internet-Draft IDMEFv2 April 2023 "Biometric", "Policy", "Heat", "Movement", "Blackhole", "Signature", "Statistical", "Heuristic", "Integrity", "Honeypot", "Tarpit", "Recon", "Correlation", "Monitor", "AI", "Threshold", "ext-value" ], "description": "Possible analyzer method" }, "vectorCategoryEnum": { "enum": [ "Unknown", "Face", "RunningMan", "Human", "Man", "Woman", "Children", "Animal", "Object", "Blast", "Fire", "Wind", "Snow", "Rain", "Chemical", "Smoke", "Vapors", "Drug", "Device", "Drone", "Car", "Truck", "Vehicle", "Bird", "Storm", "HighTemperature", Lehmann Expires 18 October 2023 [Page 84] Internet-Draft IDMEFv2 April 2023 "Artifact", "Autonomous System", "Directory", "Domain Name", "Email Address", "Email Message", "File", "IPv4 Address", "IPv6 Address", "Mutex", "Network Traffic", "Process", "URL", "User Account", "Windows Registry Key", "X509 Certificate", "ext-value" ], "description": "Possible vector category" }, "attachmentNameType": { "description": "A a unique identifier among attachments.", "type": "string", "pattern": "^[a-zA-Z0-9]+$" }, "portType": { "description": "A network port number. The value 0 is excluded from the range because it never appears in an actual network connection.", "type": "integer", "minimum": 0, "maximum": 65535, "exclusiveMinimum": true }, "timestampType": { "description": "A JSON string containing a timestamp conforming to the format given in section 5.6 of RFC 3339.", "type": "string", "pattern": "^[0-9]{4}-(0[0-9]|1[012])-([0-2][0-9]|3[01])T([0-1][0-9]|2[0-3]):[0-5][0-9]:([0-5][0-9]|60)(\\.[0-9]+)?(Z|[-+]([0-1][0-9]|2[0-3]):[0-5][0-9])?$" }, "geolocType": { "description": "Geolocation coordinates. The format for this type matches the definition for locations inside ISO 6709 (eg. \"+48.75726, +2.299528, +65.1\").", "type": "string", "pattern": "^[-+]?([0-9]+(\\.[0-9]*)?)(, ?[-+]?([0-9]+(\\.[0-9]*)?)){1,2}$" }, "unlocodeType": { "description": "A valid UN/LOCODE location (e.g. \"FR PAR\"). See also the UN/LOCODE Code List 2020-2 at https://unece.org/trade/cefact/unlocode-code-list-country-and-territory.", "type": "string", "pattern": "^[A-Z]{2} ?[A-Z]{3}$" }, "ipType": { Lehmann Expires 18 October 2023 [Page 85] Internet-Draft IDMEFv2 April 2023 "description": "An Internet Protocol address, either version 4 or version 6.", "type": "string", "pattern": "^(((25[0-5]|2[0-4][0-9]|[01]?[0-9][0-9]?)\\.){3}(25[0-5]|2[0-4][0-9]|[01]?[0-9][0-9]?)|([0-9a-fA-F]{1,4}:){7,7}[0-9a-fA-F]{1,4}|([0-9a-fA-F]{1,4}:){1,7}:|([0-9a-fA-F]{1,4}:){1,6}:[0-9a-fA-F]{1,4}|([0-9a-fA-F]{1,4}:){1,5}(:[0-9a-fA-F]{1,4}){1,2}|([0-9a-fA-F]{1,4}:){1,4}(:[0-9a-fA-F]{1,4}){1,3}|([0-9a-fA-F]{1,4}:){1,3}(:[0-9a-fA-F]{1,4}){1,4}|([0-9a-fA-F]{1,4}:){1,2}(:[0-9a-fA-F]{1,4}){1,5}|[0-9a-fA-F]{1,4}:((:[0-9a-fA-F]{1,4}){1,6})|:((:[0-9a-fA-F]{1,4}){1,7}|:)|fe80:(:[0-9a-fA-F]{0,4}){0,4}%[0-9a-zA-Z]{1,}|::(ffff(:0{1,4}){0,1}:){0,1}((25[0-5]|(2[0-4]|1{0,1}[0-9]){0,1}[0-9])\\.){3,3}(25[0-5]|(2[0-4]|1{0,1}[0-9]){0,1}[0-9])|([0-9a-fA-F]{1,4}:){1,4}:((25[0-5]|(2[0-4]|1{0,1}[0-9]){0,1}[0-9])\\.){3,3}(25[0-5]|(2[0-4]|1{0,1}[0-9]){0,1}[0-9]))$" }, "mediatypeType": { "description": "A valid media type (e.g. \"text/plain\") conforming to the format defined in section 3.1.1.1 of RFC 7231. See also http://www.iana.org/assignments/media-types/media-types.xhtml.", "type": "string", "pattern": "^[-!#$%&'*+.^_`|~0-9a-zA-Z]+/[-!#$%&'*+.^_`|~0-9a-zA-Z]+([ \t]*;[ \t]*[-!#$%&'*+.^_`|~0-9a-zA-Z]+=([-!#$%&'*+.^_`|~0-9a-zA-Z]+|\"([]-~\t !#-[\\x80-\\xFF]|\\\\([\t 0-9a-zA-Z\\x80-\\xFF]))*\"))*$" }, "uuidType": { "description": "Canonical textual representation for an UUID, as defined in RFC 4122 (e.g. \"e5f9bbae-163e-42f9-a2f2-0daaf78fefb1\")", "type": "string", "pattern": "^[0-9A-Fa-f]{8}(-[0-9A-Fa-f]{4}){3}-[0-9A-Fa-f]{12}$" }, "protocolType": { "description": "A JSON string containing a service or protocol name from the set of permitted values defined in the IANA \"Service Name and Transport Protocol Port Number\" registry (http://www.iana.org/assignments/service-names-port-numbers/service-names-port-numbers.xhtml).", "type": "string", "pattern": "^[a-zA-Z0-9](-?[a-zA-Z0-9])*$" }, "hashType": { "description": "A cryptographic hash acting as a checksum for some content, using the format \"function:hex-value\" (e.g. \"md5:dc89f0b4ff9bd3b061dd66bb66c991b1\").", "type": "string", "pattern": "^[a-zA-Z0-9-]+:([a-fA-F0-9]{2})+$" } }, "$schema": "http://json-schema.org/draft-04/schema#", "title": "IDMEF 2.D.V01" } Author's Address Gilles Lehmann Telecom Sud Paris France Email: gilles.lehmann@telecom-sudparis.eu Lehmann Expires 18 October 2023 [Page 86]