BFD Working Group C. Lin Internet Draft New H3C Technologies Intended status: Informational W. Cheng Expires: October 27, 2023 W. Jiang China Mobile April 26, 2023 BFD Path Consistency over SR draft-lin-bfd-path-consistency-over-sr-01 Abstract Bidirectional Forwarding Detection (BFD) can be used to monitor paths between nodes. U-BFD defined in [I-D.ietf-bfd-unaffiliated-echo] can effectively reduce the device equipment. Seamless BFD (S-BFD) provides a simplified mechanism which is suitable for monitoring of paths that are setup dynamically and on a large scale network. In SR network, BFD can also be used to monitor SR paths. When a headend use BFD to monitor the segment list/CPath of SR Policy, the forward path of control packet is indicated by segment list, the reverse path of response control packet is via the shortest path from the reflector back to the initiator (headend) as determined by routing. The forward path and reverse path of control packet are likely inconsistent going through different intermediate nodes or links. This document describes a method to keep the forward path and reverse path consistent when using S-BFD or U-BFD to detect SR Policy Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Lin, et al. Expire October, 2023 [Page 1] Internet-Draft BFD Path Consistency April 2023 Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html This Internet-Draft will expire on October 27 2023. Copyright Notice Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction ................................................ 3 1.1. Requirements Language .................................. 4 2. Path consistency for BFD in SR network ...................... 4 2.1. S-BFD .................................................. 5 2.2. U-BFD .................................................. 6 3. Path consistency for S-BFD .................................. 6 3.1. Correlate bidirectional path using Path Segment ........ 6 3.2. Procedure of S-BFD ..................................... 8 3.2.1. S-BFD in SRv6 ..................................... 8 3.2.2. S-BFD in SR-MPLS ................................. 11 4. Path consistency for U-BFD ................................. 14 4.1. Getting reverse segment list .......................... 14 4.2. Procedure of U-BFD .................................... 15 4.2.1. U-BFD in SRv6 .................................... 15 4.2.2. U-BFD in SR-MPLS ................................. 18 Lin, et al. Expires October, 2023 [Page 2] Internet-Draft BFD Path Consistency April 2023 5. IANA Considerations ........................................ 20 6. Security Considerations .................................... 20 7. References ................................................. 20 7.1. Normative References .................................. 20 Contributors .................................................. 22 Authors' Addresses ............................................ 23 1. Introduction Segment Routing (SR) allows a headend node to steer a packet flow along any path. Per-path states of Intermediate nodes are eliminated thanks to source routing. The headend node steers a flow into an SR Policy. The packets steered into an SR Policy carry an ordered list of segments associated with that SR Policy. SR can be instantiated on the MPLS data plane (MPLS-SR) and the IPv6 data plane (SRv6). On the MPLS-SR data plane, a segment is encoded as an MPLS label, and an ordered list of segments is encoded as a stack of labels. On the SRv6 data plane, a segment is encoded as an IPv6 address (SRv6 SID) [RFC8986], and an ordered list of segments is encoded as an ordered list of SRv6 SIDs in the SR header (SRH) [RFC8754]. BFD Echo function was originally defined in [RFC5880] and [RFC5881], where the remote system is required to loop the BFD Echo packets back to the local system. To support BFD Echo Function, some negotiations between the local system and remote system are needed, and both the local and remote system need to maintain the BFD session state. Unaffiliated BFD Echo Function (U-BFD) is defined in [I-D.ietf-bfd- unaffiliated-echo].Where the destination IP address of the BFD Echo packets is set to one of the IP addresses of the local system. Therefore, the Echo packets can be automatically looped back (through normal IP forwarding) by the remote system to the local system. With U-BFD, the remote system does not need to support any BFD related functions and maintain any session states. This further simplifies the BFD Echo Function process at the remote system hence greatly increases scalability. Seamless BFD (S-BFD) defined in [RFC7880] provides a simplified mechanism which is suitable for monitoring of paths that are setup dynamically and on a large scale network. In the SR network, the headend node could use BFD(S-BFD or U-BFD) to monitor the connectivity of the SR path to implement path switching. When a headend use BFD to monitor the segment list/CPath of SR Policy, the forward path of control packet is indicated by segment Lin, et al. Expires October, 2023 [Page 3] Internet-Draft BFD Path Consistency April 2023 list, the reverse path of response control packet is via the shortest path from the reflector back to the initiator (headend) as determined by routing. The forward path and reverse path of control packet are likely inconsistent going through different intermediate nodes or links. The inconsistency impacts the detecting result. If the forward path is up and reverse path is down, then the BFD session will be down. If there are multiple path (segment list) in a SR Policy between a headend (local system) node and a tailend(remote system) node, multiple BFD session will be created for each path. Each BFD session uses corresponding path to send control packet, but the reverse path is identical for all BFD sessions. If the reverse path is down, all sessions will be down. Then the SR Policy is down. The consistency of forward and reverse path of the same BFD session should be guaranteed. This document describes how to ensure the consistency of the forward path and the reverse path when using BFD to detect SR Policy. 1.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 2. Path consistency for BFD in SR network Monitor SR Policy using BFD is usually based on segment list. BFD session is created for each segment list and associated with the segment list. Referring to the following topology, there are two paths between Node A and D, and All nodes allocate end.x Segments on SRv6 data plane or adjacency SIDs on SR-MPLS data plane. Node A and D are headend and tailend nodes of each other, and SR policy is created on A and D respectively. Lin, et al. Expires October, 2023 [Page 4] Internet-Draft BFD Path Consistency April 2023 SID-B1 SID-B2 SID-C1 SID-C2 +--------B-----------------C-----------+ SID-A1/ \ SID-D1 / \ A D \ / SID-A2\ SID-E1 SID-E2 /SID-D2 +-------------------E-------------------+ Figure 1: reference topology Assuming that the deployed SR policy has one candidate path and each path has two segment lists. For ease of description, segment lists with the same number on Node A and D are forward and reverse paths to each other. Node A: Node D: SR Policy A-D SR Policy D-A Candidate Path1 Candidate Path1 Segment list1 Segment list1 SID-A1, SID-B2, SID-C2 SID-D1, SID-C1, SID-B1 Segment list2 Segment list2 SID-A2, SID-E2 SID-D2, SID-E1 Both Node A and Node D serve as head nodes and need to detect the connectivity of the segment list of a SR Policy. Regardless of whether S-BFD or U-BFD is used, there is a requirement for BFD packet path consistency. 2.1. S-BFD When node A is the S-BFD initiator, S-BFD sessions for segment list1 and segment list2 could be created respectively. Node A will use the associated segment list to encapsulate IPv6 header and SRH of the control packet. As the S-BFD reflector, after Node D receives the S-BFD control packet, the response control packet should be able to return along the same path to avoid the false detection of the session caused by the inconsistency of the forward and reverse paths. The control packet of S-BFD session associated with the segment list1 is forwarded to node D according to the segment list1 of node A. The response control packet of node D needs to be returned to Lin, et al. Expires October, 2023 [Page 5] Internet-Draft BFD Path Consistency April 2023 node A according to the segment list1 of node D. Thus the forward and reverse paths of S-BFD packets are ensured to be consistent. 2.2. U-BFD The working mechanism of U-BFD is that the local system sends a bfd echo packet, and the destination address is the IP address of the local system. After the bfd echo packet reaches the remote system, the remote system returns the bfd echo packet to the local system in the data plane. So U-BFD usually works when there is only one hop between the local and remote systems. When deploying U-BFD in SR network, local system could creates a U- BFD session for each segment list under the SR Policy, and uses the segment list to encapsulate BFD echo packets. For SR-MPLS encapsulation is the label stack, for SRv6 it is the segment list in SRH. In this way, the U-BFD echo packet can reach the remote system through multiple hops. When the U-BFD echo packet reaches the remote system, the destination address of the packet has been updated to the IP address of the local system, so the remote system sends the U-BFD echo packet back to the local system on the data plane. The U-BFD echo packet returned from remote system to local system should follow the same path from local system to remote system. 3. Path consistency for S-BFD This draft proposes to forward S-BFD control packets and response control packets through the consistent path by path segment. 3.1. Correlate bidirectional path using Path Segment A Path Segment is defined to identify an SR path. In SR for MPLS data plane (SR-MPLS), Path Segment is defined in [draft-ietf-spring- mpls-path-segment]. In SR for IPv6 data plane (SRv6), Path Segment is defined in [I-D.ietf-spring-srv6-path-segment]. SR(SR-MPLS or SRv6) Path segments can be used to correlate the two unidirectional SR paths at both ends of the paths. [I-D.ietf-idr-sr-policy-path-segment] proposes an extension to BGP SR Policy distribute SR policies carrying Path Segment and bidirectional path information. Lin, et al. Expires October, 2023 [Page 6] Internet-Draft BFD Path Consistency April 2023 Through this extension, when distributing SR policy to the headend node, reverse path information and path segment of segment list can be carried together. Node A Node D SR Policy A-D SR Policy D-A Candidate Path1 Candidate Path1 Segment list1 Segment list1 SID-A1, SID-B2, SID-C2 SID-D1, SID-C1, SID-B1 Path Segment: SID-Path-1 Path Segment: SID-Path-2 Reverse Path Segment: Reverse Path Segment: SID-Path-2 SID-Path-1 Segment list2 Segment list2 SID-A2, SID-E2 SID-D2, SID-E1 Path Segment: SID-Path-3 Path Segment: SID-Path-4 Reverse Path Segment: Reverse Path Segment: SID-Path-4 SID-Path-3 In this way, on the headend node in both directions of the forward and reverse paths, the path segment of the paths in both directions can be obtained, and the paths in both directions use the same intermediate links. The headend node can use path segment in two directions to establish a mapping table. Using this mapping table, the headend node can get the reverse path through the path segment of the forward path. The mapping table of Node A and Node D is shown below: Node A: +-----------------+ +--------------------+ | Path Segment | |Reverse Path Segment| +-----------------+ +--------------------+ | SID-Path-1 |-+ | SID-Path-2 |--+ +-----------------+ | +--------------------+ | | SID-Path-3 | | | SID-Path-4 |--|-+ +-----------------+ | +--------------------+ | | | | | | | | +-----------------------+ | | | | | segment List | | | | | +-----------------------+ | | | +->|SID-A1, SID-B2, SID-C2 |<----+ | | +-----------------------+ | +-------------->|SID-A2, SID-E2 |<------+ +-----------------------+ Lin, et al. Expires October, 2023 [Page 7] Internet-Draft BFD Path Consistency April 2023 Node D: +-----------------+ +--------------------+ | Path Segment | |Reverse Path Segment| +-----------------+ +--------------------+ | SID-Path-2 |-+ | SID-Path-1 |--+ +-----------------+ | +--------------------+ | | SID-Path-4 | | | SID-Path-3 |--|-+ +-----------------+ | +--------------------+ | | | | | | | | +-----------------------+ | | | | | segment List | | | | | +-----------------------+ | | | +->|SID-D1, SID-C1, SID-B1 |<----+ | | +-----------------------+ | +-------------->|SID-D2, SID-E1 |<------+ +-----------------------+ Figure 2: mapping table For instance, the S-BFD initiator is Node A in Figure 1, and the S- BFD session is bounded with Segment List1 of Policy A-D. The following sub-section describes the processing of S-BFD in SR-MPLS and SRv6 networks respectively. 3.2. Procedure of S-BFD 3.2.1. S-BFD in SRv6 o S-BFD Initiator procedure Refer to [I-D.draft-liu-spring-bfd-srv6-policy-encap] for the description of how to encapsulate S-BFD packet with SRv6 Policy. When path segment is used, the encapsulation format of S-BFD control packet is as follows: Lin, et al. Expires October, 2023 [Page 8] Internet-Draft BFD Path Consistency April 2023 +-----------------------------------------------+ | IPv6 Header | . Source IP Address = Initiator's IPv6 Address . . Destination IP Address = SegmentList[SL] . . Next-Header = SRH (43) . . . +-----------------------------------------------+ | SRH as specified in RFC 8754 | . Next-Header = IPv6 . . . . . +-----------------------------------------------+ | | . sbfd-payload . | | +-----------------------------------------------+ NodeA Encapsulates the path segment of segment list1 in SRH, and set SRH.P-Flag. The S-BFD control packet is encapsulated and forwarded as follows: A------------->B------------>C---------->D +-----------------+ +-----------------+ | SA=A's Ipv6Addr | | SA=A's Ipv6Addr | +-----------------+ +-----------------+ | DA=SID-B1 | | DA=D's ipv6Addr | +-----------------+ +-----------------+ | SL=2 | P-Flag=1 | | SL=0 | P-Flag=1 | +-----------------+ +-----------------+ | D's ipv6Addr | | D's ipv6Addr | +-----------------+ +-----------------+ | SID-C2 | | SID-C2 | +-----------------+ +-----------------+ | SID-B2 | | SID-B2 | +-----------------+ +-----------------+ | SID-A1 | | SID-A1 | +-----------------+ +-----------------+ | SID-Path-1 | | SID-Path-1 | +-----------------+ +-----------------+ | sbfd-payload | | sbfd-payload | | | | | +-----------------+ +-----------------+ Figure 3: Example of S-BFD control packet Lin, et al. Expires October, 2023 [Page 9] Internet-Draft BFD Path Consistency April 2023 o S-BFD Reflector procedure S-BFD control packet is forwarded along the path A->B->C-D. While packet arrives at Node D, SRH.SL is 0 and the destination address is IPv6 address of Node D. Packet is delivered up to the S-BFD module in control plane. S-BFD module detects SRH.P-flag is set, extracts the path segment of the forward path from SRH, gets the path segment of the reverse path through the mapping table. When responding to S-BFD control packet, S-BFD module uses the segment list associated with path segment of the reverse path to encapsulate SRH. The encapsulation format of S-BFD response control packet is as follows: +-----------------------------------------------+ | IPv6 Header | . Source IP Address = Reflector's IPv6 Address . . Destination IP Address = SegmentList[SL] . . Next-Header = SRH (43) . . . +-----------------------------------------------+ | SRH as specified in RFC 8754 | . Next-Header = IPv6 . . . . . +-----------------------------------------------+ | | . sbfd-payload . | | +-----------------------------------------------+ The S-BFD response packet is encapsulated and forwarded as follows: Lin, et al. Expires October, 2023 [Page 10] Internet-Draft BFD Path Consistency April 2023 D------------->C------------>B---------->A +-----------------+ +-----------------+ | SA=D's Ipv6Addr | | SA=D's Ipv6Addr | +-----------------+ +-----------------+ | DA=SID-C1 | | DA=A's ipv6Addr | +-----------------+ +-----------------+ | SL=2 | P-Flag=0 | | SL=0 | P-Flag=0 | +-----------------+ +-----------------+ | A's ipv6Addr | | A's ipv6Addr | +-----------------+ +-----------------+ | SID-B1 | | SID-B1 | +-----------------+ +-----------------+ | SID-C1 | | SID-C1 | +-----------------+ +-----------------+ | SID-D1 | | SID-D1 | +-----------------+ +-----------------+ | sbfd-payload | | sbfd-payload | | | | | +-----------------+ +-----------------+ The S-BFD response control packet will be forward along the path D- >C->B->A. In this way, the forward and reverse paths of S-BFD are guaranteed to be consistent. 3.2.2. S-BFD in SR-MPLS o S-BFD Initiator procedure The encapsulation format using SR Policy with path segment of S-BFD control packet is as follows: Lin, et al. Expires October, 2023 [Page 11] Internet-Draft BFD Path Consistency April 2023 +--------------------+ | ... | +--------------------+ | Label 1 | +--------------------+ | Label 2 | +--------------------+ | ... | +--------------------+ | Label n | +--------------------+ | Path Segment | +--------------------+ | IPv6 Header: | | Source IP | | Destination IP | ~ ~ +--------------------+ ~ sbfd-Payload ~ +--------------------+ Node A Encapsulates the segment list1 and path segment in label stack. The source IP is the IPv6 address of Node A, and the destination IP is the IPv6 address of Node D. The S-BFD control packet is encapsulated and forwarded as follows: A------------->B------------>C---------->D +-----------------+ | SID-A1 | +-----------------+ | SID-B2 | +-----------------+ | SID-C2 | +-----------------+ +-----------------+ | SID-Path-1 | | SID-Path-1 | +-----------------+ +-----------------+ | SA=A's Ipv6Addr | | SA=A's Ipv6Addr | +-----------------+ +-----------------+ | DA=D's ipv6Addr | | DA=D's ipv6Addr | +-----------------+ +-----------------+ | sbfd-payload | | sbfd-payload | | | | | +-----------------+ +-----------------+ o S-BFD Reflector procedure Lin, et al. Expires October, 2023 [Page 12] Internet-Draft BFD Path Consistency April 2023 S-BFD control packet is forwarded along the path A->B->C-D. When the packet arrives at node D, the top-level label is path segment. Packet with path segment is delivered up to the S-BFD module in control plane. When responding to S-BFD control packet, the S-BFD module uses the mapping table to find the label stack of the reverse path through the path segment to encapsulate the response control packet. The encapsulation format of S-BFD response control packet is as follows: The source IP is the IPv6 address of Node D, and the destination IP is the IPv6 address of Node A. +--------------------+ | ... | +--------------------+ | Label 1 | +--------------------+ | Label 2 | +--------------------+ | ... | +--------------------+ | Label n | +--------------------+ | IPv6 Header: | | Source IP | | Destination IP | ~ ~ +--------------------+ ~ sbfd-Payload ~ +--------------------+ The S-BFD response packet is encapsulated and forwarded as follows: Lin, et al. Expires October, 2023 [Page 13] Internet-Draft BFD Path Consistency April 2023 D------------->C------------>B---------->A +-----------------+ | SID-D1 | +-----------------+ | SID-C1 | +-----------------+ | SID-B1 | +-----------------+ +-----------------+ | SA=D's Ipv6Addr | | SA=D's Ipv6Addr | +-----------------+ +-----------------+ | DA=A's Ipv6Addr | | DA=A's Ipv6Addr | +-----------------+ +-----------------+ | sbfd-payload | | sbfd-payload | | | | | +-----------------+ +-----------------+ 4. Path consistency for U-BFD This document proposes to encapsulate the segment list of the return path in the U-BFD echo packet to guide the packet from the remote system to the local system along the same path. 4.1. Getting reverse segment list [I-D.ietf-idr-sr-policy-path-segment] proposes an extension to BGP SR Policy distribute SR policies carrying reverse path information. The reverse path information includes reverse segment list and reverse path segment. The reverse path segment can be used for S-BFD path consistency, and the reverse segment list can be used for U-BFD path consistency. Referring to the example topology, the SR Policy on nodes A and D that contains complete reverse path information is as follows Node A Node D SR Policy A-D SR Policy D-A Candidate Path1 Candidate Path1 Segment list1 Segment list1 SID-A1, SID-B2, SID-C2 SID-D1, SID-C1, SID-B1 Path Segment: SID-Path-1 Path Segment: SID-Path-2 Reverse segment list Reverse Segment list SID-D1, SID-C1, SID-B1 SID-A1, SID-B2, SID-C2 Reverse Path Segment: Reverse Path Segment: Lin, et al. Expires October, 2023 [Page 14] Internet-Draft BFD Path Consistency April 2023 SID-Path-2 SID-Path-1 Segment list2 Segment list2 SID-A2, SID-E2 SID-D2, SID-E1 Path Segment: SID-Path-3 Path Segment: SID-Path-4 Reverse segment list Reverse segment list SID-D2, SID-E1 SID-A2, SID-E2 Reverse Path Segment: Reverse Path Segment: SID-Path-4 SID-Path-3 4.2. Procedure of U-BFD The headend node uses U-BFD to detect a segment list of SR-Policy. In order to achieve path consistency, the reverse segment list can be encapsulated in the U-BFD echo packet at the same time. When the U-BFD echo packet reaches the tailend node of SR-Policy, it will be looped back to the headend node according to the path specified by the reverse segment list. According to this method, when the segment list in the SR-Policy and its corresponding reverse segment list are planned to pass through the same intermediate link, the U-BFD echo packet's round-trip path will be consistent. 4.2.1. U-BFD in SRv6 In SRv6, the reverse segment list can be encapsulated in one SRH with the forward segment list, or it can be encapsulated in an independent SRH When the forward and reverse segment lists are in the same SRH, the encapsulation is as follows Lin, et al. Expires October, 2023 [Page 15] Internet-Draft BFD Path Consistency April 2023 +--------------------------------------------+ | IPv6 Header | . Source IP Address = Node A's IPv6 Address . . Destination IP Address = SegmentList[SL] . . Next-Header = SRH (43) . . . +--------------------------------------------+ | SRH as specified in RFC 8754 | . Next-Header = IPv6 . . Node A's IPv6 Address . . . . . . . +--------------------------------------------+ | | . ubfd-payload . | | +--------------------------------------------+ When the forward and reverse segment lists are in different SRHs, the encapsulation is as follows +--------------------------------------------+ | IPv6 Header | . Source IP Address = Node A's IPv6 Address . . Destination IP Address = SegmentList[SL] . . Next-Header = SRH (43) . . . +--------------------------------------------+ | SRH as specified in RFC 8754 | . Next-Header = SRH (43) . . . . . +--------------------------------------------+ | SRH as specified in RFC 8754 | . Next-Header = IPv6 . . Node A's IPv6 Address . . . . . +--------------------------------------------+ | | . ubfd-payload . | | +--------------------------------------------+ Lin, et al. Expires October, 2023 [Page 16] Internet-Draft BFD Path Consistency April 2023 Referring to the sample topology, take node A as the head node and D as the tail node as an example. Node A uses U-BFD to detect segment list1. The forward segment list and reverse segment list and the address of node A are encapsulated in one SRH. The U-BFD echo packet is encapsulated and forwarded as follows: A------------->B------------>C---------->D +-----------------+ +-----------------+ | SA=A's Ipv6Addr | | SA=A's Ipv6Addr | +-----------------+ +-----------------+ | DA=SID-B2 | | DA=SID-D1 | +-----------------+ +-----------------+ | SL=5 | | SL=3 | +-----------------+ +-----------------+ | A's ipv6Addr | | A's ipv6Addr | +-----------------+ +-----------------+ | SID-B1 | | SID-B1 | +-----------------+ +-----------------+ | SID-C1 | | SID-C1 | +-----------------+ +-----------------+ | SID-D1 | | SID-D1 | +-----------------+ +-----------------+ | SID-C2 | | SID-C2 | +-----------------+ +-----------------+ | SID-B2 | | SID-B2 | +-----------------+ +-----------------+ | SID-A1 | | SID-A1 | +-----------------+ +-----------------+ | ubfd-payload | | ubfd-payload | | | | | +-----------------+ +-----------------+ Figure 7: Example of U-BFD echo packet in SRv6 After the u-BFD packet reaches Node D, Node D continues to forward the u-BFD packet according to the SRH, and returns the U-BFD echo packet to Node A. Lin, et al. Expires October, 2023 [Page 17] Internet-Draft BFD Path Consistency April 2023 D------------->C------------>B---------->A +-----------------+ +-----------------+ | SA=A's Ipv6Addr | | SA=A's Ipv6Addr | +-----------------+ +-----------------+ | DA=SID-C1 | | DA=A's ipv6Addr | +-----------------+ +-----------------+ | SL=2 | | SL=0 | +-----------------+ +-----------------+ | A's ipv6Addr | | A's ipv6Addr | +-----------------+ +-----------------+ | SID-B1 | | SID-B1 | +-----------------+ +-----------------+ | SID-C1 | | SID-C1 | +-----------------+ +-----------------+ | SID-D1 | | SID-D1 | +-----------------+ +-----------------+ | SID-C2 | | SID-C2 | +-----------------+ +-----------------+ | SID-B2 | | SID-B2 | +-----------------+ +-----------------+ | SID-A1 | | SID-A1 | +-----------------+ +-----------------+ | sbfd-payload | | sbfd-payload | | | | | +-----------------+ +-----------------+ The U-BFD echo packet will be forward along the path D->C->B->A. In this way, the forward and reverse paths of U-BFD are guaranteed to be consistent. 4.2.2. U-BFD in SR-MPLS In SR-MPLS, The segment list and the reverse segment list can be encapsulated in the label stack at the same time. Lin, et al. Expires October, 2023 [Page 18] Internet-Draft BFD Path Consistency April 2023 +--------------------+ | ... | +--------------------+ | | . label stack . | | +--------------------+ | | . reverse label stack. | | +--------------------+ | IPv6 Header: | | Source IP | | Destination IP | ~ ~ +--------------------+ ~ ubfd-Payload ~ +--------------------+ Take node A as the headend node and D as the tailend node as an example, Node A uses U-BFD to detect segment list1. In order to achieve consistent paths, the encapsulation and processing of U-BFD echo packets are as follows A------------->B------------>C---------->D +-----------------+ | SID-A1 | +-----------------+ | SID-B2 | +-----------------+ | SID-C2 | +-----------------+ +-----------------+ | SID-D1 | | SID-D1 | +-----------------+ +-----------------+ | SID-C1 | | SID-C1 | +-----------------+ +-----------------+ | SID-B1 | | SID-B1 | +-----------------+ +-----------------+ | SA=A's Ipv6Addr | | SA=A's Ipv6Addr | +-----------------+ +-----------------+ | DA=A's ipv6Addr | | DA=A's ipv6Addr | +-----------------+ +-----------------+ | ubfd-payload | | ubfd-payload | | | | | +-----------------+ +-----------------+ Lin, et al. Expires October, 2023 [Page 19] Internet-Draft BFD Path Consistency April 2023 After the u-BFD packet reaches Node D, Node D continues to forward the u-BFD packet according to the label stack, and returns the U-BFD echo packet to Node A. D------------->C------------>B---------->A +-----------------+ | SID-D1 | +-----------------+ | SID-C1 | +-----------------+ | SID-B1 | +-----------------+ +-----------------+ | SA=A's Ipv6Addr | | SA=A's Ipv6Addr | +-----------------+ +-----------------+ | DA=A's Ipv6Addr | | DA=A's Ipv6Addr | +-----------------+ +-----------------+ | ubfd-payload | | ubfd-payload | | | | | +-----------------+ +-----------------+ 5. IANA Considerations This document has no IANA actions. 6. Security Considerations The security requirements and mechanisms described in [RFC8402] and [RFC8754] also apply to this document. This document does not introduce any new security consideration. 7. References 7.1. Normative References [I-D.draft-liu-spring-bfd-srv6-policy-encap] Liu, Y., Cheng, W., Lin, C., Chen, M., "Encapsulation of BFD for SRv6 Policy", draft-liu-spring-bfd-srv6-policy-encap-00(work in progress), October 2022 [I-D.ietf-bfd-unaffiliated-echo] Cheng, W., Wang, R., Min, X., Rahman, R., and R. C. Boddireddy, "Unaffiliated BFD Echo", Work in Progress, Internet-Draft, draft-ietf-bfd- unaffiliated-echo-06, 25 March 2023, . Lin, et al. Expires October, 2023 [Page 20] Internet-Draft BFD Path Consistency April 2023 [I-D.ietf-idr-segment-routing-te-policy] Previdi, S., Filsfils, C., Talaulikar, K., Mattes, P., Jain, D., and S. Lin, "Advertising Segment Routing Policies in BGP", draft-ietf- idr-segment-routing-te-policy-20 (work in progress), July 2022 [I-D.ietf-spring-mpls-path-segment] Cheng, W., Li, H., Chen, M., Gandhi, R., and R. Zigler, "Path Segment in MPLS Based Segment Routing Network",draft-ietf-spring-mpls-path- segment-08 (work in progress), September 2022. [I-D.ietf-spring-srv6-path-segment] Li, C., Cheng, W., Chen, M., Dhody, D., and Y. Zhu, "Path Segment for SRv6 (Segment Routing in IPv6)", draft-ietf-spring-srv6-path-segment-05 (work in progress),October 2022. [I-D.ietf-idr-sr-policy-path-segment] Li, C., Li, Z., Yin, Y., Cheng, W., Talaulikar, K., "SR Policy Extensions for Path Segment and Bidirectional Path", draft-ietf-idr-sr-policy- path-segment-07(work in progress), February 2023. [RFC5880] Katz, D. and D. Ward, "Bidirectional Forwarding Detection (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,. [RFC5881] Katz, D. and D. Ward, "Bidirectional Forwarding Detection (BFD) for IPv4 and IPv6 (Single Hop)", RFC 5881, DOI 10.17487/RFC5881, June 2010, . [RFC7880] Pignataro, C., Ward, D., Akiya, N., Bhatia, M., and S. Pallagatti, "Seamless Bidirectional Forwarding Detection (S-BFD)", RFC 7880, DOI 10.17487/RFC7880, July 2016, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,Decraene, B., Litkowski, S., and R. Shakir, "Segment Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,July 2018, . [RFC8754] Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J., Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header (SRH)", RFC 8754, DOI 10.17487/RFC8754, March 2020, . Lin, et al. Expires October, 2023 [Page 21] Internet-Draft BFD Path Consistency April 2023 [RFC8986] Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer, D., Matsushima, S., and Z. Li, "Segment Routing over IPv6 (SRv6) Network Programming", RFC 8986, DOI 0.17487/RFC8986, February 2021, . [RFC9252] Dawra, G., Ed., Talaulikar, K., Ed., Raszuk, R., Decraene, B., Zhuang, S., and J. Rabadan, "BGP Overlay Services Based on Segment Routing over IPv6 (SRv6)", RFC 9252, DOI 10.17487/RFC9252, July 2022, . Contributors Yisong Liu contributed to the content of this document. Lin, et al. Expires October, 2023 [Page 22] Internet-Draft BFD Path Consistency April 2023 Authors' Addresses Changwang Lin New H3C Technologies Beijing China Email: linchangwang.04414@h3c.com Weiqiang Cheng China Mobile Beijing CN Email: chengweiqiang@chinamobile.com Wenying Jiang China Mobile Beijing CN Email: jiangwenying@chinamobile.com Lin, et al. Expires October, 2023 [Page 23]